Dynojet Power Commander V Installation Instructions
  1. Manuals
  2. Brands
  3. Dynojet Manuals
  4. Automobile Electronics
  5. Power commander V
  6. Installation instructions
Dynojet Power Commander V Installation Instructions

Dynojet Power Commander V Installation Instructions

2004-2009 aprilia rsv mille
Hide thumbs Also See for Power Commander V:
1
2
3
4
5

Quick Links

2004-2009 Aprilia RSV Mille
I n s t a l l a t i o n I n s t r u c t i o n s
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
10-003
www.powercommander.com
2191 Mendenhall Drive North Las Vegas, NV 89081 (800) 992-4993 www.powercommander.com
PARTS LIST
1
Power Commander
1
USB Cable
1
Installation Guide
2
Power Commander Decals
2
Dynojet Decals
4
Velcro strips
1
Alcohol swab
1
Posi-tap
THE IGNITION MUST BE TURNED
OFF BEFORE INSTALLATION!
THE LATEST POWER COMMANDER
SOFTWARE AND MAP FILES CAN BE
DOWNLOADED FROM OUR WEB SITE AT:
www.powercommander.com
2004-2009 Aprilia RSV Mille - PCV - 1
loading

Related Manuals for Dynojet Power Commander V

Summary of Contents for Dynojet Power Commander V

  • Page 1 USB Cable Installation Guide 2004-2009 Aprilia RSV Mille Power Commander Decals I n s t a l l a t i o n I n s t r u c t i o n s Dynojet Decals Velcro strips Alcohol swab Posi-tap THE IGNITION MUST BE TURNED...

  • Page 2: Usb Connection

    POWER COMMANDER V INPUT ACCESSORY GUIDE ACCESSORY INPUTS Map - (Input 1 or 2) The PCV has the ability to hold 2 different base maps. You can switch on the fly between these two base maps when you hook up a switch to the MAP inputs. You can USB CONNECTION use any open/close type switch. The polarity of the wires is not important. When using the Autotune kit one position will hold a base map and the other position will let you activate the learning mode. When the switch is “CLOSED” Autotune will be activated. (Set to Switch Input #1 by default.) Shifter- (Input 1 or 2) These inputs are for use with the Dynojet quickshifter. Insert the wires from the CRANK Dynojet quickshifter into the SHIFTER inputs. ANALOG The polarity of the wires is not important. (Set to Switch Input #2 by default.) SPEED EXPANSION PORTS 1 & 2 INPUT 2 (Grnd)
  • Page 3 FIG.A Remove the seats. Prop the front of the fuel tank up. Lay the PCV in the tail section and route the PCV wiring harness forward along the right side of the frame and towards the engine. PCV Harness Attach the PCV ground wire with the small ring lug to the negative (-) terminal of the bike’s battery (Fig. A). FIG.B Unplug Unplug the stock wiring harness from the rear fuel injector (Fig. B). This connection is on the left side of the throttle body. FIG.C Plug the pair of PCV leads with YELLOW colored wires in-line of the stock wiring harness and the rear fuel injector (Fig. C). 10-003 www.powercommander.com 2004-2009 Aprilia RSV Mille - PCV - 3...
  • Page 4 FIG.D Use the supplied Posi-tap to attach the single GREY wire of the PCV to the stock BROWN/WHITE wire of the bike’s Throttle Position Sensor wiring harness (Fig. D). The TPS is located to the left, rear of the throttle body. FIG.E Route the ORANGE colored wires from the PCV to the right side of the throttle body. Unplug Unplug the stock wiring harness from the front fuel injector (Fig. E). This connection is on the right side of the throttle body. FIG.F 10 Plug the pair of PCV leads with ORANGE colored wires in-line of the stock wiring harness and the front fuel injector (Fig. F). 10-003 www.powercommander.com 2004-2009 Aprilia RSV Mille - PCV - 4...
  • Page 5 FIG.G 11 Secure the PCV module in the tail section using the remaining Velcro (Fig. G). Clean all surfaces with the supplied alcohol swab prior to applying the Velcro adhesive. PCV Module 12 Reinstall all of the removed bodywork, the fuel tank, and the seats. 10-003 www.powercommander.com 2004-2009 Aprilia RSV Mille - PCV - 5...