Dynojet Power Commander V Installation Instructions
For triumph street triple 675
Hide thumbs
Also See for Power Commander V:
- Installation instructions manual (9 pages) ,
- Installation manual (9 pages) ,
- Installation instructions and owner's manuals (8 pages)
Quick Links
2008-2012 Triumph Street Triple 675
I n s t a l l a t i o n I n s t r u c t i o n s
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
I21-004
www.powercommander.com
2191 Mendenhall Drive North Las Vegas, NV 89081 (800) 992-4993 www.powercommander.com
PARTS LIST
1
Power Commander
1
USB Cable
1
Installation Guide
2
Power Commander Decals
2
Dynojet Decals
2
Velcro strips
1
Alcohol swab
THE IGNITION MUST BE TURNED
OFF BEFORE INSTALLATION!
THE LATEST POWER COMMANDER
SOFTWARE AND MAP FILES CAN BE
DOWNLOADED FROM OUR WEB SITE AT:
www.powercommander.com
2008-2012 Triumph Street Triple 675 - PCV - 1
Related Manuals for Dynojet Power Commander V
Summary of Contents for Dynojet Power Commander V
- Page 1 USB Cable Installation Guide 2008-2012 Triumph Street Triple 675 Power Commander Decals Dynojet Decals I n s t a l l a t i o n I n s t r u c t i o n s Velcro strips Alcohol swab THE IGNITION MUST BE TURNED...
- Page 2 POWER COMMANDER V INPUT ACCESSORY GUIDE ACCESSORY INPUTS Map - (Input 1 or 2) The PCV has the ability to hold 2 different base maps. You can switch on the fly between these two base maps when you hook up a switch to the MAP inputs. You can USB CONNECTION use any open/close type switch. The polarity of the wires is not important. When using the Autotune kit one position will hold a base map and the other position will let you activate the learning mode. When the switch is “CLOSED” Autotune will be activated. (Set to Switch Input #1 by default.) Shifter- (Input 1 or 2) These inputs are for use with the Dynojet quickshifter. Insert the wires from the CRANK Dynojet quickshifter into the SHIFTER inputs. ANALOG The polarity of the wires is not important. (Set to Switch Input #2 by default.) SPEED EXPANSION PORTS 1 & 2 INPUT 2 (Grnd)
- Page 3 FIG.A Remove the seat. Remove the fuel tank. Secure the PCV to the rear of the battery (Fig. A). Route the PCV harness to the left side of the battery and go towards the throttle bodies. Attach the ground wire of the PCV to the negative side of the battery (Fig. A). FIG.B Unplug the stock wiring harness from each fuel injector (Fig. B). Squeeze the sides of the connector to remove. Unplug the crank position sensor connectors (Fig. B). This is a WHITE 2-pin connector pair. Unplug FIG.C Plug the PCV harness in-line of the stock wiring harness and each fuel injector. PCV harness: ORANGE - cylinder #1 (left) YELLOW - cylinder #2 GREEN - cylinder #3 (right) I21-004 www.powercommander.com 2008-2012 Triumph Street Triple 675 - PCV - 3...
- Page 4 FIG.D Plug the PCV harness in-line of the stock wiring harness and crank position sensor harness (Fig. D). FIG.E 10 Locate the Throttle Position Sensor connector. Unplug this connector (Fig. E). Unplug This is a BLACK 3-pin connector pair located to the right and rear of the throttle bodies just inside the frame rail. FIG.F Stock 11 Plug the PCV wiring harness in-line of the stock TPS connectors (Fig. F). 12 Reinstall the fuel tank and the seat. Stock I21-004 www.powercommander.com 2008-2012 Triumph Street Triple 675 - PCV - 4...