Dynojet Power Commander V Installation Instructions Manual
Fuel and ignition; 2016 yamaha kodiak 700
Hide thumbs
Also See for Power Commander V:
- Installation instructions manual (9 pages) ,
- Installation manual (9 pages) ,
- Installation instructions and owner's manuals (8 pages)
Quick Links
FUEL AND IGNITION
2016 Yamaha Kodiak 700
I n s t a l l a t i o n I n s t r u c t i o n s
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
22-076
www.powercommander.com
2191 Mendenhall Drive North Las Vegas, NV 89081 (800) 992-4993 www.powercommander.com
PARTS LIST
1
Power Commander
1
USB Cable
1
Installation Guide
2
Power Commander Decals
2
Dynojet Decals
2
Velcro strips
1
Alcohol swab
THE IGNITION MUST BE TURNED
OFF BEFORE INSTALLATION!
THE LATEST POWER COMMANDER
SOFTWARE AND MAP FILES CAN BE
DOWNLOADED FROM OUR WEB SITE AT:
www.powercommander.com
2016 Yamaha Kodiak 700 - PCV F/I - 1
Related Manuals for Dynojet Power Commander V
Summary of Contents for Dynojet Power Commander V
- Page 1 FUEL AND IGNITION Installation Guide Power Commander Decals 2016 Yamaha Kodiak 700 Dynojet Decals I n s t a l l a t i o n I n s t r u c t i o n s Velcro strips Alcohol swab THE IGNITION MUST BE TURNED...
-
Page 2: Usb Connection
POWER COMMANDER V INPUT ACCESSORY GUIDE ACCESSORY INPUTS Map - (Input 1 or 2) The PCV has the ability to hold 2 different base maps. You can switch on the fly between these two base maps when you hook up a switch to the MAP inputs. You can USB CONNECTION use any open/close type switch. The polarity of the wires is not important. When using the Autotune kit one position will hold a base map and the other position will let you activate the learning mode. When the switch is “CLOSED” Autotune will be activated. (Set to Switch Input #1 by default.) Shifter- (Input 1 or 2) These inputs are for use with the Dynojet quickshifter. Insert the wires from the CRANK Dynojet quickshifter into the SHIFTER inputs. ANALOG The polarity of the wires is not important. (Set to Switch Input #2 by default.) SPEED EXPANSION PORTS 1 & 2 INPUT 2 (Grnd) - Page 3 FIG.A Remove the seat. Remove the front covers (Fig. A). Remove this cover FIG.B Remove Remove the right, top, and left side covers around the engine (Fig. B). Remove the cargo box. FIG.C Remove the intake tube for the CVT clutch on the right hand side of the quad (Fig. C). Remove This allows access to the Crank Position Sensor connectors. Place the PCV in the battery area temporarily. Route the PCV harness down the right hand side of the quad towards the throttle body. 22-076 www.powercommander.com 2016 Yamaha Kodiak 700 - PCV F/I - 3...
- Page 4 FIG.D Unplug the stock wiring harness from the Fuel Injector (Fig. D). The Fuel Injector is directly on top of the throttle body. FIG.E Plug the pair of PCV connectors with ORANGE colored wires in-line of the stock wiring harness and the Fuel Injector (Fig. E). FIG.F 10 Locate and unplug the stock wiring harness from the Throttle Position Sensor (Fig. F). The TPS is located on the left side of the throttle body. 22-076 www.powercommander.com 2016 Yamaha Kodiak 700 - PCV F/I - 4...
- Page 5 FIG.G 11 Plug the pair of 3-pin connectors of the PCV in-line of the Throttle Position Sensor and the stock wiring harness (Fig. G). FIG.H 12 Locate and unplug the stock connectors from the Crank Position Sensor (Fig. H). This is a pair of WHITE 2-pin connectors on the right side of the engine, just Unplug above the CVT clutch belt housing. FIG.J 13 Plug the WHITE 2-pin connectors from the PCV wiring harness in-line of the stock Crank Position Sensor connectors (Fig. J). 22-076 www.powercommander.com 2016 Yamaha Kodiak 700 - PCV F/I - 5...
- Page 6 FIG.K Unplug 14 Locate the Ignition Coil on the right side of the quad forward of the engine and unplug the 2 stock coil wires (Fig. K). The coil has 1 RED/BLACK wire and 1 ORANGE wire. FIG.L 15 Plug the GREEN and WHITE/GREEN wires of the PCV wiring harness in-line of the coil and the stock ORANGE wire. 16 Plug the RED/WHITE wires of the PCV wiring harness in-line of the coil and the stock RED/BLACK wire (Fig. L). FIG.M 17 Attach the ground wire from the PCV to the negative side of the battery. 18 Install the included port covers onto your PCV. 19 Secure the PCV near the battery using the supplied Velcro (Fig. M). Make sure to use the alcohol swab to clean both surfaces before attaching. Ground 20 Reinstall the intake tube for the CVT clutch, the cargo box, the bodywork, the and the seat. 22-076 www.powercommander.com 2016 Yamaha Kodiak 700 - PCV F/I - 6...