Dynojet Power Commander V Installation Instructions Manual
  1. Manuals
  2. Brands
  3. Dynojet Manuals
  4. Motorcycle Accessories
  5. Power commander V
  6. Installation instructions manual
Dynojet Power Commander V Installation Instructions Manual

Dynojet Power Commander V Installation Instructions Manual

2009-2010 ktm adventurer
Hide thumbs Also See for Power Commander V:
1
2
3
4
5
6
7

Quick Links

2009-2010 KTM Adventurer
I n s t a l l a t i o n I n s t r u c t i o n s
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
18-003
www.powercommander.com
2191 Mendenhall Drive North Las Vegas, NV 89081 (800) 992-4993 www.powercommander.com
PARTS LIST
1
Power Commander
1
USB Cable
1
CD-ROM
1
Installation Guide
2
Power Commander Decals
2
Dynojet Decals
2
Velcro
1
Alcohol swab
2
O2 Optimizer
THE IGNITION MUST BE TURNED
OFF BEFORE INSTALLATION!
YOU CAN ALSO DOWNLOAD THE
POWER COMMANDER SOFTWARE AND
LATEST MAPS FROM OUR WEB SITE AT:
www.powercommander.com
KTM Adventurer PCV - 1
loading

Related Manuals for Dynojet Power Commander V

Summary of Contents for Dynojet Power Commander V

  • Page 1 CD-ROM 2009-2010 KTM Adventurer Installation Guide Power Commander Decals I n s t a l l a t i o n I n s t r u c t i o n s Dynojet Decals Velcro Alcohol swab O2 Optimizer THE IGNITION MUST BE TURNED...

  • Page 2: Usb Connection

    POWER COMMANDER V ACCESSORY INPUTS INPUT ACCESSORY GUIDE Map - The PCV has the ability to hold 2 different base maps. You can switch on the fly between these two base maps when you hook up a switch to the MAP inputs. You can use any open/close type switch. The polarity of the wires is not important. When using the USB CONNECTION Autotune kit one position will hold a base map and the other position will let you activate the learning mode. When the switch is “CLOSED” Autotune will be activated. Shifter- These inputs are for use with the Dynojet quickshifter. Insert the wires from the Dynojet quickshifter into the SHIFTER inputs. The polarity of the wires is not important. CRANK Speed- If your application has a speed sensor then you can ANALOG tap into the signal side of the sensor and run a wire SPEED into this input. This will allow you to calculate gear position in the Control Center Software. Once gear EXPANSION PORTS 1 & 2 INPUT 2...
  • Page 3 FIG.A Remove the main seat. Remove the storage cover and storage shell (Fig. A) FIG.B Remove the right and left hand side panels and fuel tanks (Fig. B). Ground wire FIG.C Remove the 3 bolts for the tail section on the right hand side (Fig. C). Secure the PCV in tail section using the supplied velcro. Route the PCV harness under the tail section and go towards the front of the bike (Fig. C). 18-003 www.powercommander.com KTM Adventurer PCV - 3...
  • Page 4 FIG.D Route the PCV harness inside of the frame rails and go towards the front of the engine (Fig. D). FIG.E Unplug the stock throttle body sub-connector (Fig. E). This is a GREY 16 pin connector on the right side of the frame. FIG.F Plug the PCV main connectors in-line of the stock wiring harness (Fig. F). 18-003 www.powercommander.com KTM Adventurer PCV - 4...
  • Page 5 FIG.G 10 Locate the stock Crank Pickup Coil Sensor on the right side of the motorcycle. Unplug this connection (Fig. G). This is a WHITE 2 pin connector near the bottom of the oil reservoir tank. FIG.H 11 Plug the WHITE connectors from the PCV in-line of the crank sensor connectors (Fig. H). FIG.I 12 Attach the ground wire from the PCV to the stock ground location on the right side of the frame (Fig. I). This is located near the crank sensor connector. 18-003 www.powercommander.com KTM Adventurer PCV - 5...
  • Page 6 FIG.J 13 Unplug the stock wiring harness from the front coil stick (Fig. J). FIG.K 14 Plug the PCV GREEN wires in-line of the stock coil stick and stock wiring harness (Fig. K). FIG.L 15 Unplug the stock wiring harness from the rear coil stick (Fig. L) 18-003 www.powercommander.com KTM Adventurer PCV - 6...
  • Page 7 17 Locate the front cylinder O2 sensor connection. This connection is on the right side of the frame above the ground location from step 12. It is a BLACK 4 pin connector. 18 Unplug this connection and plug one of the Dynojet O2 Optimizers into the stock wiring harness (Fig. N). The stock O2 sensor will no longer be connected to anything.