Dynojet Power commander V Installation Instructions
  1. Manuals
  2. Brands
  3. Dynojet Manuals
  4. Power Supply
  5. Power commander V
  6. Installation instructions
Dynojet Power commander V Installation Instructions

Dynojet Power commander V Installation Instructions

2018 triumph street triple 765
Hide thumbs Also See for Power commander V:
1
2
3
4
5

Quick Links

2018 Triumph Street Triple 765
I n s t a l l a t i o n I n s t r u c t i o n s
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
21-024
www.powercommander.com
2191 Mendenhall Drive North Las Vegas, NV 89081 (800) 992-4993 www.powercommander.com
PARTS LIST
1
Power Commander
1
USB Cable
1
Installation Guide
2
Power Commander Decals
2
Dynojet Decals
2
Velcro strips
1
Alcohol swab
THE IGNITION MUST BE TURNED
OFF BEFORE INSTALLATION!
THE LATEST POWER COMMANDER
SOFTWARE AND MAP FILES CAN BE
DOWNLOADED FROM OUR WEB SITE AT:
www.powercommander.com
2018 Triumph Street Triple 765 - PCV - 1
loading

Related Manuals for Dynojet Power commander V

Summary of Contents for Dynojet Power commander V

  • Page 1 USB Cable Installation Guide Power Commander Decals 2018 Triumph Street Triple 765 Dynojet Decals Velcro strips I n s t a l l a t i o n I n s t r u c t i o n s Alcohol swab THE IGNITION MUST BE TURNED...

  • Page 2: Usb Connection

    POWER COMMANDER V INPUT ACCESSORY GUIDE ACCESSORY INPUTS Map - (Input 1 or 2) The PCV has the ability to hold 2 different base maps. You can switch on the fly between these two base maps when you hook up a switch to the MAP inputs. You can USB CONNECTION use any open/close type switch. The polarity of the wires is not important. When using the Autotune kit one position will hold a base map and the other position will let you activate the learning mode. When the switch is “CLOSED” Autotune will be activated. (Set to Switch Input #1 by default.) Shifter- (Input 1 or 2) These inputs are for use with the Dynojet quickshifter. Insert the wires from the CRANK Dynojet quickshifter into the SHIFTER inputs. ANALOG The polarity of the wires is not important. (Set to Switch Input #2 by default.) SPEED EXPANSION PORTS 1 & 2 INPUT 2 (Grnd)
  • Page 3 FIG.A Remove the seat. Remove the fuel tank. Remove the airbox. Disassemble the body work surrounding the tail section. Remove the side Remove panels and the cross-member bracket above the charcoal canister (Fig. A). FIG.B Secure the PCV module in the tail section rear of the charcoal canister with the supplied Velcro. Use the supplied alcohol swab to clean surfaces before attaching the Velcro (Fig. B). Route the PCV wiring harness forward towards the engine long the right side of the frame. FIG.C Secure the PCV ground wire with the small ring terminal to the stock common ground bolt at the top of the engine case (Fig. C). 21-024 www.powercommander.com 2018 Triumph Street Triple 765 - PCV - 3...
  • Page 4 FIG.D Unplug Unplug the stock Crank Position Sensor connectors (Fig. D). This is a BLACK 6-pin connector pair located at the top of the engine case. FIG.E Plug the PCV wiring harness in-line of the stock Crank Position Sensor connectors (Fig. E). FIG.F Unplug all three Fuel Injectors. Plug the PCV wiring harness in-line of each Fuel Injector and the stock wiring harness (Fig. F). PCV ORANGE wires go to Cylinder #1. PCV YELLOW wires go to Cylinder #2. PCV GREEN wires go to Cylinder #3. 21-024 www.powercommander.com 2018 Triumph Street Triple 765 - PCV - 4...
  • Page 5 FIG.G Unplug 10 Unplug the stock wiring harness from the Throttle Position Sensor on the right hand side of the throttle bodies (Fig. G). FIG.H 11 Plug the PCV wiring harness in-line of the Throttle Position Sensor and the stock wiring harness (Fig. H). 12 Reassemble the tail. Reinstall the airbox. Reinstall the fuel tank and the seat. 21-024 www.powercommander.com 2018 Triumph Street Triple 765 - PCV - 5...