Dynojet Power Commander V Installation Instructions Manual
2009-2013 honda vt750c2
Hide thumbs
Also See for Power Commander V:
- Installation manual (9 pages) ,
- Installation instructions manual (9 pages) ,
- Installation instructions and owner's manuals (8 pages)
Quick Links
FUEL AND IGNITION
2009-2013 Honda VT750C2
I n s t a l l a t i o n I n s t r u c t i o n s
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
I16-017
www.powercommander.com
2191 Mendenhall Drive North Las Vegas, NV 89081 (800) 992-4993 www.powercommander.com
PARTS LIST
1
Power Commander
1
USB Cable
1
CD-ROM
1
Installation Guide
2
Power Commander Decals
2
Dynojet Decals
2
Velcro
1
Alcohol swab
1
Posi-tap
THE IGNITION MUST BE TURNED
OFF BEFORE INSTALLATION!
YOU CAN ALSO DOWNLOAD THE
POWER COMMANDER SOFTWARE AND
LATEST MAPS FROM OUR WEB SITE AT:
www.powercommander.com
2009-2013 Honda VT750 PCV-F/I - 1
Related Manuals for Dynojet Power Commander V
Summary of Contents for Dynojet Power Commander V
- Page 1 CD-ROM Installation Guide 2009-2013 Honda VT750C2 Power Commander Decals I n s t a l l a t i o n I n s t r u c t i o n s Dynojet Decals Velcro Alcohol swab Posi-tap THE IGNITION MUST BE TURNED OFF BEFORE INSTALLATION!
-
Page 2: Usb Connection
POWER COMMANDER V INPUT ACCESSORY GUIDE ACCESSORY INPUTS Map - The PCV has the ability to hold 2 different base maps. You can switch on the fly between these two base maps when you hook up a switch to the MAP inputs. You can use USB CONNECTION any open/close type switch. The polarity of the wires is not important. When using the Autotune kit one position will hold a base map and the other position will let you activate the learning mode. When the switch is “CLOSED” Autotune will be activated. (Set to Input 1 by default.) Shifter- These inputs are for use with the Dynojet quickshifter. Insert the wires from the Dynojet CRANK quickshifter into the SHIFTER inputs. The ANALOG polarity of the wires is not important. (Set to Input 2 by default.) SPEED EXPANSION PORTS 1 & 2 INPUT 2 Speed-... - Page 3 FIG.A Remove the seat and fuel tank. Removing the fuel tank is tricky since there is not a dry-break on the fuel line to the fuel pump. Either drain the fuel or have someone hold the fuel tank up while performing the install Lay the PCV in the battery area and route the harness up the right side of the Unplug frame following the stock wiring harness.
- Page 4 FIG.D Locate the rear ignition coil behind the right hand side cover (Fig. D). Unbolt this coil so that the bottom wires can be accessed. Unplug the BLACK/WHITE and YELLOW/BLUE wires from the coil. BLK/WHT YEL/BLU FIG.E 10 Plug the set of RED colored wires of the PCV in-line with the BLACK/WHITE coil wire and the coil. 11 Plug the set of BLUE colored wires of the PCV in-line with the YELLOW/BLUE coil wire and the coil. 12 Bolt the rear coil back to its mounting bracket. FIG.F 13 Locate and unplug the Crank Position Sensor connectors on the right hand side of the bike, up by the steering stem (Fig. F). This is the set of RED, 2-pin connectors. I16-017 www.powercommander.com 2009-2013 Honda VT750 PCV-F/I - 4...
- Page 5 FIG.G 14 Plug the set of RED, 2-pin connectors of the PCV wiring harness in-line with the bike’s Crank Position Sensor connectors (Fig. G). FIG.H 15 Locate the front ignition coil on the left hand side of the bike above the front cylinder head (Fig. H). BLU/YEL 16 Unplug the BLUE/YELLOW wire from the coil. FIG.I 17 Plug the set of GREEN colored wires of the PCV in-line with the BLUE/ YELLOW wire and the coil. I16-017 www.powercommander.com 2009-2013 Honda VT750 PCV-F/I - 5...
- Page 6 FIG.J 18 Remove the battery tray lid. 19 Attach the ground wire from the PCV to the negative side of the battery (Fig. J). Ground 20 Reinstall battery tray lid making sure it does not pinch the ground wire. FIG.K 21 Secure the PCV to the top of the battery tray lid using the supplied velcro. (Fig. K). 22 Reinstall fuel tank and seat. I16-017 www.powercommander.com 2009-2013 Honda VT750 PCV-F/I - 6...