Dynojet Power Commander V Installation Instructions
  1. Manuals
  2. Brands
  3. Dynojet Manuals
  4. Motorcycle Accessories
  5. Power commander V
  6. Installation instructions

Dynojet Power Commander V Installation Instructions

For ducati m1200
Hide thumbs Also See for Power Commander V:
1
2
3
4
5

Quick Links

FUEL AND IGNITION
2014-2016 Ducati M1200
I n s t a l l a t i o n I n s t r u c t i o n s
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
I14-033
www.powercommander.com
2191 Mendenhall Drive North Las Vegas, NV 89081 (800) 992-4993 www.powercommander.com
PARTS LIST
1
Power Commander
1
USB Cable
1
Installation Guide
2
Power Commander Decals
2
Dynojet Decals
2
Velcro strips
1
Alcohol swab
THE IGNITION MUST BE TURNED
OFF BEFORE INSTALLATION!
YOU CAN ALSO DOWNLOAD THE
POWER COMMANDER SOFTWARE AND
LATEST MAPS FROM OUR WEB SITE AT:
www.powercommander.com
2014-2016 Ducati M1200 - PCV F/I - 1
loading

Related Manuals for Dynojet Power Commander V

Summary of Contents for Dynojet Power Commander V

  • Page 1 FUEL AND IGNITION Installation Guide Power Commander Decals 2014-2016 Ducati M1200 Dynojet Decals I n s t a l l a t i o n I n s t r u c t i o n s Velcro strips Alcohol swab THE IGNITION MUST BE TURNED...

  • Page 2: Usb Connection

    POWER COMMANDER V INPUT ACCESSORY GUIDE ACCESSORY INPUTS Map - (Input 1 or 2) The PCV has the ability to hold 2 different base maps. You can switch on the fly between these two base maps when you hook up a switch to the MAP inputs. You can USB CONNECTION use any open/close type switch. The polarity of the wires is not important. When using the Autotune kit one position will hold a base map and the other position will let you activate the learning mode. When the switch is “CLOSED” Autotune will be activated. (Set to Switch Input #1 by default.) Shifter- (Input 1 or 2) These inputs are for use with the Dynojet quickshifter. Insert the wires from the CRANK Dynojet quickshifter into the SHIFTER inputs. ANALOG The polarity of the wires is not important. (Set to Switch Input #2 by default.) SPEED EXPANSION PORTS 1 & 2 INPUT 2 (Grnd)
  • Page 3 FIG.A Remove the seat and lift the fuel tank up. Lay the PCV in the tail section as shown in Figure A. Route the PCV harness down the left side of the frame and go towards the airbox. FIG.B Unplug the 6-pin connector on the left shown in Figure B. Unplug the 3-pin connector on the right shown in Figure B. FIG.C Attach the connectors from the PCV to the stock wiring harness as shown in Figure C. I14-033 www.powercommander.com 2014-2016 Ducati M1200 - PCV F/I - 3...
  • Page 4 FIG.D Unplug the stock crank position sensor connector as shown in Figure D. This is a black 3-pin connector pair located on the right side of the engine near the coolant overflow reservoir. FIG.E Attach the connectors from the PCV to the crank position sensor and stock wiring harness as shown in Figure E. FIG.F Locate and unplug the stock ignition coil connectors on the left side of the engine shown in Figure F. I14-033 www.powercommander.com 2014-2016 Ducati M1200 - PCV F/I - 4...
  • Page 5 FIG.G 10 Attach the connectors with the green wires from the PCV to the front cylinder ignition coil and stock wiring harness connector as shown in Figure G. 11 Attach the connectors with the blue wires from the PCV to the rear cylinder ignition coil and stock wiring harness connector as shown in Figure G. FIG.H 12 Attach the ground wire from the PCV harness to the case bolt on the left side of the engine as shown in Figure H. Ground 13 Reinstall the fuel tank and seat. I14-033 www.powercommander.com 2014-2016 Ducati M1200 - PCV F/I - 5...