Dynojet Power Commander V Installation Instructions Manual
  1. Manuals
  2. Brands
  3. Dynojet Manuals
  4. Automobile Accessories
  5. Power commander V
  6. Installation instructions manual

Dynojet Power Commander V Installation Instructions Manual

Fuel and ignition 2012-2013 kawasaki teryx 4
Hide thumbs Also See for Power Commander V:
1
2
3
4
5
6

Quick Links

See also: Installation Instructions & Owner's Manual, Instruction and Installation Manual
FUEL AND IGNITION
2012-2013 Kawasaki Teryx 4
I n s t a l l a t i o n I n s t r u c t i o n s
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
17-044
www.powercommander.com
2191 Mendenhall Drive North Las Vegas, NV 89081 (800) 992-4993 www.powercommander.com
PARTS LIST
1
Power Commander
1
USB Cable
1
CD-ROM
1
Installation Guide
2
Power Commander Decals
2
Dynojet Decals
2
Velcro
1
Alcohol swab
THE IGNITION MUST BE TURNED
OFF BEFORE INSTALLATION!
YOU CAN ALSO DOWNLOAD THE
POWER COMMANDER SOFTWARE AND
LATEST MAPS FROM OUR WEB SITE AT:
www.powercommander.com
2012-2013 Kawasaki Teryx 4 PCV F/I - 1
loading

Related Manuals for Dynojet Power Commander V

Summary of Contents for Dynojet Power Commander V

  • Page 1 FUEL AND IGNITION Installation Guide 2012-2013 Kawasaki Teryx 4 Power Commander Decals Dynojet Decals I n s t a l l a t i o n I n s t r u c t i o n s Velcro Alcohol swab THE IGNITION MUST BE TURNED...
  • Page 2 POWER COMMANDER V INPUT ACCESSORY GUIDE ACCESSORY INPUTS Map - (Input 1 or 2) The PCV has the ability to hold 2 different base maps. You can switch on the fly between these two base maps when you hook up a switch to the MAP inputs. You can USB CONNECTION use any open/close type switch. The polarity of the wires is not important. When using the Autotune kit one position will hold a base map and the other position will let you activate the learning mode. When the switch is “CLOSED” Autotune will be activated. (Input 1 or 2) These inputs are for use with the Shifter- Dynojet quickshifter. Insert the wires from the Dynojet quickshifter into the SHIFTER inputs. CRANK The polarity of the wires is not important. ANALOG Speed- If your application has a speed sensor then SPEED you can tap into the signal side of the sensor EXPANSION PORTS 1 & 2 INPUT 2 and run a wire into this input. This will allow...
  • Page 3 FIG.A Remove Remove both of the front seats and the engine cover (Fig. A). FIG.B Locate and unplug the BLACK 2-pin connectors for the vehicle’s Crank Position Sensor under the passenger seat just in front of the fuel tank (Fig. B). The plastic kick panel under the seats was removed in this picture for demonstration purposes, but does not need to be removed for the purpose of this installation. FIG.C Secure the module under the front passenger seat in the location shown in Figure C. Use the supplied Velcro to secure the module. Clean both surfaces with the supplied alcohol swab prior to applying the Velcro.
  • Page 4 FIG.D Locate and unplug the stock wiring harness from the throttle bodies (Fig. D). Unplug This is a BLACK 6-pin connector located at the right side of the engine. FIG.E Plug the PCV connectors in-line of the stock wiring harness and throttle body harness (Fig. E). FIG.F Route the PCV wiring harness leads with the GREEN colored wires towards the Front Ignition Coil. Unplug The Front Ignition Coil is located at the front of the airbox. Unplug the GREEN Ignition Coil wire with the CLEAR insulator towards the front of the Ignition Coil. This is the forward wire originally going to the GREEN pin of the coil. 17-044 www.powercommander.com 2012-2013 Kawasaki Teryx 4 PCV F/I - 4...
  • Page 5 FIG.G 10 Plug the GREEN colored wires of the PCV wiring harness in-line of the GREEN Front Ignition Coil pin and the stock GREEN Front Ignition Coil wire with the CLEAR insulator (Fig. G). FIG.H 11 Route the PCV wiring harness leads with the RED and BLUE colored wires towards the Rear Ignition Coil. The Rear Ignition Coil is located at the rear of the airbox. 12 Unplug the WHITE coil wire with the CLEAR insulator from the upper coil pin. This is the upper wire originally going to the GREEN pin of the coil. 13 Unplug the BROWN coil wire with the BLACK insulator from the lower coil pin (Fig. H). This is the lower wire originally going to the BLACK pin of the coil.
  • Page 6 FIG.J 16 Secure the ground wire of the PCV wiring harness with the eyelet to the bolt Ground that holds the Rear Ignition Coil to its bracket (Fig. J). 17 Reinstall the engine cover and seats. 17-044 www.powercommander.com 2012-2013 Kawasaki Teryx 4 PCV F/I - 6...