Dynojet Power Commander V Installation Instructions
For yamaha yz450f 2014
Hide thumbs
Also See for Power Commander V:
- Installation instructions manual (9 pages) ,
- Installation manual (9 pages) ,
- Installation instructions and owner's manuals (8 pages)
Quick Links
FUEL AND IGNITION
2014 Yamaha YZ450F
I n s t a l l a t i o n I n s t r u c t i o n s
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
22-063
www.powercommander.com
2191 Mendenhall Drive North Las Vegas, NV 89081 (800) 992-4993 www.powercommander.com
PARTS LIST
1
Power Commander
1
USB Cable
1
CD-ROM
1
Installation Guide
2
Power Commander Decals
2
Dynojet Decals
2
Velcro
1
Alcohol swab
1
Posi-tap
1
Zip tie
THE IGNITION MUST BE TURNED
OFF BEFORE INSTALLATION!
YOU CAN ALSO DOWNLOAD THE
POWER COMMANDER SOFTWARE AND
LATEST MAPS FROM OUR WEB SITE AT:
www.powercommander.com
2014 Yamaha YZ450F F/I PCV - 1
Related Manuals for Dynojet Power Commander V
Summary of Contents for Dynojet Power Commander V
- Page 1 USB Cable CD-ROM FUEL AND IGNITION Installation Guide 2014 Yamaha YZ450F Power Commander Decals Dynojet Decals I n s t a l l a t i o n I n s t r u c t i o n s Velcro Alcohol swab Posi-tap Zip tie THE IGNITION MUST BE TURNED...
-
Page 2: Usb Connection
POWER COMMANDER V INPUT ACCESSORY GUIDE ACCESSORY INPUTS Map - (Input 1 or 2) The PCV has the ability to hold 2 different base maps. You can switch on the fly between these two base maps when you hook up a switch to the MAP inputs. You can USB CONNECTION use any open/close type switch. The polarity of the wires is not important. When using the Autotune kit one position will hold a base map and the other position will let you activate the learning mode. When the switch is “CLOSED” Autotune will be activated. (Set to Input 1 by default.) Shifter- (Input 1 or 2) These inputs are for use with the Dynojet quickshifter. Insert the wires from the CRANK Dynojet quickshifter into the SHIFTER inputs. ANALOG The polarity of the wires is not important. (Set to Input 2 by default.) SPEED EXPANSION PORTS 1 & 2 INPUT 2 (Grnd) - Page 3 FIG.A Remove the seat. Remove the radiator shrouds on both sides (Fig. A). Remove the fuel tank. The fuel tank does not need to be completely removed; but it does need to be loosened and lifted out place to access the ECU and throttle body. FIG.B Remove the right ECU bolt, and pull the ECU loose from its mounting location (Fig. B). FIG.C Install the PCV module to the right hand side of the frame using the supplied Velcro and/or the zip tie (Fig. C). Route the PCV harness to the inside of the frame and go towards the throttle body. The shorter harness branch with the pair of WHITE 2-pin connectors and BROWN colored wires will need to go towards the left radiator.
- Page 4 FIG.D Secure the PCV ground wire with the ring lug to the common ground located on the frame just below the PCV module mounting location (Fig. D). PCV ground FIG.E Loosen the rubber boot surrounding the stock ECU connector. Feed the single unterminated GREY wire of the PCV wiring harness through the rubber boot. 10 Use the supplied Posi-tap to attach the PCV GREY wire to the stock YELLOW wire on the ECU connector (Fig. E). 11 Pull the rubber boot back over the ECU connector. FIG.F 12 Unplug the BLACK 2-pin connector for the Ignition Coil. 13 Unplug the GREY 2-pin connector for the Fuel Injector (Fig. F). 22-063 www.powercommander.com 2014 Yamaha YZ450F F/I PCV - 4...
- Page 5 FIG.G 14 Plug the PCV wiring harness in-line of the Fuel Injector and stock wiring harness. 15 Plug the PCV wiring harness in-line of the Ignition Coil and stock wiring harness (Fig. G). 16 Secure the ECU back to its original mounting location. FIG.H 17 Remove the 2 bolts that secure the left radiator to the frame. This helps to access the stock Crank Position Sensor connectors just behind the radiator next to the frame. Unplug 18 Locate and unplug the stock Crank Position Sensor connectors (Fig. H). This is a pair of GREY 2-pin connectors. They are on the frame inside a BLACK rubber boot.