Dynojet Power Commander V Installation Instructions Manual
  1. Manuals
  2. Brands
  3. Dynojet Manuals
  4. Motorcycle Accessories
  5. Power commander V
  6. Installation instructions manual

Dynojet Power Commander V Installation Instructions Manual

2010-2013 honda vt1300 models, fuel and ignition
Hide thumbs Also See for Power Commander V:
1
2
3
4
5
6

Quick Links

See also: Installation Instructions & Owner's Manual, Instruction and Installation Manual
FUEL AND IGNITION
2010-2013 Honda VT1300 models
I n s t a l l a t i o n I n s t r u c t i o n s
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
I16-025
www.powercommander.com
2191 Mendenhall Drive North Las Vegas, NV 89081 (800) 992-4993 www.powercommander.com
PARTS LIST
1
Power Commander
1
USB Cable
1
CD-ROM
1
Installation Guide
2
Power Commander Decals
2
Dynojet Decals
2
Velcro
1
Alcohol swab
1
Posi-tap
THE IGNITION MUST BE TURNED
OFF BEFORE INSTALLATION!
YOU CAN ALSO DOWNLOAD THE
POWER COMMANDER SOFTWARE AND
LATEST MAPS FROM OUR WEB SITE AT:
www.powercommander.com
10-13 Honda VT1300 Models - PCV F/I - 1
loading

Related Manuals for Dynojet Power Commander V

Summary of Contents for Dynojet Power Commander V

  • Page 1 CD-ROM Installation Guide 2010-2013 Honda VT1300 models Power Commander Decals I n s t a l l a t i o n I n s t r u c t i o n s Dynojet Decals Velcro Alcohol swab Posi-tap THE IGNITION MUST BE TURNED...

  • Page 2: Usb Connection

    POWER COMMANDER V INPUT ACCESSORY GUIDE ACCESSORY INPUTS Map - (Input 1 or 2) The PCV has the ability to hold 2 different base maps. You can switch on the fly between these two base maps when you hook up a switch to the MAP inputs. You can USB CONNECTION use any open/close type switch. The polarity of the wires is not important. When using the Autotune kit one position will hold a base map and the other position will let you activate the learning mode. When the switch is “CLOSED” Autotune will be activated. (Input 1 or 2) These inputs are for use with the Shifter- Dynojet quickshifter. Insert the wires from the Dynojet quickshifter into the SHIFTER inputs. CRANK The polarity of the wires is not important. ANALOG Speed- If your application has a speed sensor then SPEED you can tap into the signal side of the sensor EXPANSION PORTS 1 & 2 INPUT 2 and run a wire into this input. This will allow...
  • Page 3 FIG.A Remove the seat. Remove the left side panel below the drivers seat. Remove the fuel tank up. Install the PCV to the front side of the battery using the stock rubber strap to secure the unit (Fig. A). Route the PCV harness along the main wiring harness on the left side of the bike. FIG.B Unplug the stock wiring harness from each injector (Fig. B). Pay attention to the orientation of the connectors. “F” is front. FIG.C Connect the PCV harness in-line of the stock wiring harness and injectors (Fig. C). The ORANGE wires from the PCV go to the front cylinder. I16-025 www.powercommander.com 10-13 Honda VT1300 Models - PCV F/I - 3...
  • Page 4 FIG.D Using the supplied posi-tap connect the GREY Posi-tap wire of the PCV to the RED/YELLOW wire of the stock Throttle Position Sensor (Fig. D). The TPS connector is located near the injector connectors FIG.E Locate the Ignition coil under the fuel tank. Unplug the stock wiring harness Black Green from the ignition coil paying attention to the wire colors. The spade terminals on the ignition coil are marked with a GREEN indicator and a BLACK indicator. FIG.F 10 Plug the PCV in-line of the ignition coil and stock wiring harness. The GREEN wires of the PCV go to the GREEN spade terminal. The RED wires of the PCV go to the BLACK terminal I16-025 www.powercommander.com...
  • Page 5 FIG.G 11 Locate the Ignition coil on the bottom side of the plastic tray that holds the upper coil from Figure E. Green 12 Unplug the stock wiring harness from the ignition coils GREEN spade terminal (Fig. G). FIG.H 13 Plug the PCV in-line of the ignition coil and stock wiring harness. The BLUE wires of the PCV go to the GREEN spade terminal. FIG.I 14 Locate the RED, 2 pin crank position sensor connector under the left hand cosmetic engine cover on the left side of the bike (Fig. I). 15 Unplug the crank position sensor connector. I16-025 www.powercommander.com 10-13 Honda VT1300 Models - PCV F/I - 5...
  • Page 6 FIG.J 16 Plug the connectors from the PCV in-line of the stock crank position sensor and wiring harness (Fig. J). 17 Reinstall engine cover making sure the PCV wires do not get damaged. FIG.K 18 Attach the ground wire of the PCV to the negative side of the battery (Fig. K). 19 Reinstall bodywork and fuel tank. Speed input - GRN/YEL wire from speed sensor - behind RH mud flap. Need to remove rear fender I16-025 www.powercommander.com 10-13 Honda VT1300 Models - PCV F/I - 6...