Dynojet Power Commander V Installation Instructions And Owner's Manuals
  1. Manuals
  2. Brands
  3. Dynojet Manuals
  4. Automobile Accessories
  5. Power commander V
  6. Installation instructions and owner's manuals

Dynojet Power Commander V Installation Instructions And Owner's Manuals

Hide thumbs Also See for Power Commander V:
1
2
3
4
5
6

Quick Links

See also: Installation Instructions & Owner's Manual, Instruction and Installation Manual
2009-2010 Ducati Hypermotard
I n s t a l l a t i o n I n s t r u c t i o n s
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
14-003 w ww.powercommander.com
2191 Mendenhall Drive North Las Vegas, NV 89081 (800) 992-4993 www.powercommander.com
PARTS LIST
1
Power Commander
1
USB Cable
1
CD-ROM
1
Installation Guide
2
Power Commander Decals
2
Dynojet Decals
2
Velcro
1
Alcohol swab
1
Posi-tap
4
Zip ties
1
Optimizer
THE IGNITION MUST BE TURNED
OFF BEFORE INSTALLATION!
YOU CAN ALSO DOWNLOAD THE
POWER COMMANDER SOFTWARE AND
LATEST MAPS FROM OUR WEB SITE AT:
www.powercommander.com
2009-2010 Ducati Hypermotard PCV - 1
loading

Related Manuals for Dynojet Power Commander V

Summary of Contents for Dynojet Power Commander V

  • Page 1 USB Cable CD-ROM Installation Guide 2009-2010 Ducati Hypermotard Power Commander Decals I n s t a l l a t i o n I n s t r u c t i o n s Dynojet Decals Velcro Alcohol swab Posi-tap Zip ties Optimizer THE IGNITION MUST BE TURNED...

  • Page 2: Usb Connection

    POWER COMMANDER V INPUT ACCESSORY GUIDE ACCESSORY INPUTS Map - The PCV has the ability to hold 2 different base maps. You can switch on the fly between these two base maps when you hook up a switch to the INPUT 1. You can USB CONNECTION use any open/close type switch. The polarity of the wires is not important. When using the Autotune kit one position will hold a base map and the other position will let you activate the learning mode. When the switch is “CLOSED” Autotune will be activated. These inputs are for use with the Dynojet Shifter- quickshifter. Insert the wires from the Dynojet quickshifter into the INPUT 2. The polarity of CRANK the wires is not important. ANALOG Speed- If your application has a speed sensor then SPEED you can tap into the signal side of the sensor EXPANSION PORTS 1 & 2 INPUT 2 and run a wire into this input. This will allow...
  • Page 3 FIG.A Remove the seat. Remove the fuel side panels. Lay the PCV near the battery and route the harness down the left hand side of the bike (Fig. A). FIG.B Continue routing the PCV harness along left hand frame rail. Route the ORANGE colored wires to the right side of the bike following the frame cross member (Fig. B). Ground wire FIG.C Unplug Unplug the stock wiring harness from the rear injector (Fig. C). This injector is located on the left hand side of the bike. 14-003 w ww.powercommander.com 2009-2010 Ducati Hypermotard PCV - 3...
  • Page 4 FIG.D PCV connector Stk connector Plug the YELLOW colored wires from the PCV in-line of the rear injector and stock wiring harness (Fig. D). PCV connector FIG.E Unplug the stock wiring harness from the front injector (Fig. E). Unplug This injector is located on the right hand side of the bike FIG.F PCV connector Plug the ORANGE colored wires from the PCV in-line of the front injector and stock wiring harness (Fig. F). PCV connector 14-003 w ww.powercommander.com 2009-2010 Ducati Hypermotard PCV - 4...
  • Page 5 FIG.G Locate the stock Throttle Position Sensor. This sensor Wire tap is located on the left side of the throttle bodies. 10 Cut a 1” slit in the sheathing for the TPS harness. This allows access to the wires. 11 Using the supplied wire tap crimp the ORANGE wire (Fig. G). Grey wire 12 Connect the GREY wire from the PCV harness to the wire tap (Fig. G). FIG.H 13 Attach the ground wire from the PCV harness to the negative terminal of the battery (Fig. H). 14 Install the PCV to the side of the battery using the supplied velcro (Fig. H) Make sure to clean both surfaces with the alcohol swab before attaching. 15 Reinstall side panels and seat. FIG.I 16 Remove the right hand side fairing 17 Locate the O2 sensor connector. It is a BLACK 4 pin connector located on the right hand side of the bike. 18 Unplug this connector. 14-003 w ww.powercommander.com 2009-2010 Ducati Hypermotard PCV - 5...
  • Page 6 FIG.I 19 Plug the Dynojet O2 Optimizer in-line of the main wiring harness and stock O2 sensor. 20 Attach the ground wire of the Optimizer to the ECU ground wire location 21 Install the O2 optimizer to the top of the fuse box assembly using the supplied velcro Notes: • When this module is installed it will control the closed loop area of the motorcycle. The closed loop area is 0-24% throttle and 0-5500rpm. The module is designed to achieve an AFR target of around 13.6:1. If you desire a different AFR call tech support at 800- 992-4993 • If you are using a PCV with this module input values of 10 in the GREY area of your map shown in Figure C EXCEPT for idle. If you are using an Auto tune module do NOT input target AFR values in this same area. 14-003 w ww.powercommander.com 2009-2010 Ducati Hypermotard PCV - 6...

This manual is also suitable for:

2009-2010 ducati hypermotard