Dynojet POWER COMMANDER V Installation Instructions
  1. Manuals
  2. Brands
  3. Dynojet Manuals
  4. Automobile Accessories
  5. Power commander V
  6. Installation instructions

Dynojet POWER COMMANDER V Installation Instructions

2019 honda talon 1000
Hide thumbs Also See for POWER COMMANDER V:
1
2
3
4
5

Quick Links

FUEL and IGNITION
2019 Honda Talon 1000
I n s t a l l a t i o n I n s t r u c t i o n s
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
16-076
2191 Mendenhall Drive North Las Vegas, NV 89081 (800) 992-4993 www.powercommander.com
www.powercommander.com
PARTS LIST
1
Power Commander
1
USB Cable
1
Installation Guide
2
Power Commander Decals
2
Dynojet Decals
2
Velcro strips
1
Alcohol swab
1
Posi-tap
THE IGNITION MUST BE TURNED
OFF BEFORE INSTALLATION!
THE LATEST POWER COMMANDER
SOFTWARE AND MAP FILES CAN BE
DOWNLOADED FROM OUR WEB SITE AT:
www.powercommander.com
2019 Honda Talon 1000 - PCV F/I - 1
loading

Related Manuals for Dynojet POWER COMMANDER V

Summary of Contents for Dynojet POWER COMMANDER V

  • Page 1 Power Commander USB Cable Installation Guide Power Commander Decals FUEL and IGNITION Dynojet Decals 2019 Honda Talon 1000 Velcro strips I n s t a l l a t i o n I n s t r u c t i o n s Alcohol swab Posi-tap...

  • Page 2: Usb Connection

    POWER COMMANDER V INPUT ACCESSORY GUIDE ACCESSORY INPUTS Map- (Input 1 or 2) The PCV has the ability to hold two different base maps. You can switch on the fly between these two base maps when you connect a switch to the MAP inputs. You USB CONNECTION can use any open/close type switch. The polarity of the wires is not important. When using the Autotune kit, one position will hold a base map and the other position will let you activate the learning mode. When the switch is “CLOSED” Autotune will be activated. (Set to Switch Input #1 by default.) Shifter- (Input 1 or 2) Not used for continuously variable transmissions. (Set to Switch Input CRANK #2 by default.) ANALOG Speed- If your application has a speed sensor then SPEED you can tap into the signal side of the sensor EXPANSION PORTS 1 & 2 INPUT 2 (Grnd) and run a wire into this input. This will allow...
  • Page 3 FIG.A Remove the large panel at the front of the cargo bed. Remove the inner fender panels that are inside of the rear fenders. Snorkel Remove the entire airbox assembly (Fig. A). Remove Remove the lid and filter. Loosen the hose clamps around the throttle bodies. Disconnect hoses and vent lines at the bottom. Remove the mounting bolts. Remove the inlet snorkel assembly separately from the main airbox. FIG.B Unplug the stock Crank Position Sensor connectors (Fig. B).
  • Page 4 FIG.D Secure the PCV ground wire with the small ring terminal to the stock common ground left of the engine on the frame (Fig. D). Ground Route the PCV wiring harness towards the throttle bodies. FIG.E Unplug the Throttle Position Sensor on the forward side of the throttle bodies. Use the supplied Posi-tap to attach the GREY wire of the PCV wiring harness to the stock BLUE/BLACK wire of the stock TPS connector. 10 Plug the TPS back in after attaching the GREY wire (Fig. E). FIG.F Unplug 11 Unplug the stock wiring harness from both of the Fuel Injectors (Fig. F). Unplug 16-076 www.powercommander.com 2019 Honda Talon 1000 - PCV F/I - 4...
  • Page 5 FIG.G 12 Plug the pair of PCV connectors with ORANGE colored wires in-line of the REAR cylinder Fuel Injector and its stock connector. 13 Plug the pair of PCV connectors with YELLOW colored wires in-line of the FRONT cylinder Fuel Injector and its stock connector (Fig. G). 14 Route the remaining PCV leads with spade connectors to the Ignition Coils. FIG.H 15 Unplug the stock 12v wire (RED/BLACK) and the signal wire (GREEN/YELLOW) from the Front Cylinder Ignition Coil. Unplug only the Rear signal wire (GREEN/ORANGE) from the Rear Cylinder Ignition Coil (Fig. H). The 12v wires are on the upper BLACK tabs and have BLACK wire sheathing. The signal wires are on the lower GREEN tabs and have GREEN wire sheathing.