Dynojet POWER COMMANDER V Installation Instructions
  1. Manuals
  2. Brands
  3. Dynojet Manuals
  4. Automobile Accessories
  5. Power commander V
  6. Installation instructions

Dynojet POWER COMMANDER V Installation Instructions

2006-2016 canam outlander 650
Hide thumbs Also See for POWER COMMANDER V:
1
2
3
4
5

Quick Links

2006-2016 CanAm Outlander 650
I n s t a l l a t i o n I n s t r u c t i o n s
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
25-013
www.powercommander.com
2191 Mendenhall Drive North Las Vegas, NV 89081 (800) 992-4993 www.powercommander.com
PARTS LIST
1
Power Commander
1
USB Cable
1
Installation Guide
2
Power Commander Decals
2
Dynojet Decals
2
Velcro strips
1
Alcohol swab
THE IGNITION MUST BE TURNED
OFF BEFORE INSTALLATION!
THE LATEST POWER COMMANDER
SOFTWARE AND MAP FILES CAN BE
DOWNLOADED FROM OUR WEB SITE AT:
www.powercommander.com
2006-2016 Can-Am Outlander 650 - PCV - 1
loading

Related Manuals for Dynojet POWER COMMANDER V

Summary of Contents for Dynojet POWER COMMANDER V

  • Page 1 2006-2016 CanAm Outlander 650 Installation Guide Power Commander Decals I n s t a l l a t i o n I n s t r u c t i o n s Dynojet Decals Velcro strips Alcohol swab THE IGNITION MUST BE TURNED OFF BEFORE INSTALLATION!

  • Page 2: Usb Connection

    POWER COMMANDER V INPUT ACCESSORY GUIDE ACCESSORY INPUTS Map - (Input 1 or 2) The PCV has the ability to hold 2 different base maps. You can switch on the fly between these two base maps when you hook up a switch to the MAP inputs. You can USB CONNECTION use any open/close type switch. The polarity of the wires is not important. When using the Autotune kit one position will hold a base map and the other position will let you activate the learning mode. When the switch is “CLOSED” Autotune will be activated. (Set to Switch Input #1 by default.) Shifter- (Input 1 or 2) These inputs are for use with the Dynojet quickshifter. Insert the wires from the CRANK Dynojet quickshifter into the SHIFTER inputs. ANALOG The polarity of the wires is not important. (Set to Switch Input #2 by default.) SPEED EXPANSION PORTS 1 & 2 INPUT 2 (Grnd)
  • Page 3 FIG.A Remove the seat. Remove the right hand side covers (Fig. A). Remove FIG.B Install the PCV to the underside of the airbox cover using the supplied Velcro (Fig. B). Make sure to clean both surfaces with the supplied alcohol swab prior to attaching the Velcro. Route the PCV wiring harness to the right side of the ATV. FIG.C Unplug the stock wiring harness from the rear fuel injector (Fig. C). 25-013 www.powercommander.com 2006-2016 Can-Am Outlander 650 - PCV - 3...
  • Page 4 FIG.D Plug the YELLOW colored wires from the PCV in-line of the stock wiring harness and the rear fuel injector (Fig. D). FIG.E Unplug the stock wiring harness from the front fuel injector (Fig. E). FIG.F Route the ORANGE colored wires from the PCV to the left hand side of the throttle body and go towards the front fuel injector. Plug the pair of PCV leads with ORANGE colored wires in-line of the stock wiring harness and the front fuel injector (Fig. F). 25-013 www.powercommander.com 2006-2016 Can-Am Outlander 650 - PCV - 4...
  • Page 5 FIG.G 10 Locate the Throttle Position Sensor on the rear side of the throttle body Unplug (Fig. G). 11 Unplug the stock wiring harness from the TPS. FIG.H 12 Plug the PCV connectors in-line of the stock wiring harness and TPS (Fig. H). FIG.J 13 Route the ground wire from the PCV to the left hand side of the throttle body and follow the stock ground wires down to the right hand side of the engine. 14 Attach the ground wire from the PCV to the common ground lug of the engine (Fig. J). 15 Reinstall the covers and the seat 25-013 www.powercommander.com 2006-2016 Can-Am Outlander 650 - PCV - 5...