Dynojet POWER COMMANDER V Installation Instructions
  1. Manuals
  2. Brands
  3. Dynojet Manuals
  4. Automobile Accessories
  5. Power commander V
  6. Installation instructions

Dynojet POWER COMMANDER V Installation Instructions

2009-2011 polaris sportsman 850
Hide thumbs Also See for POWER COMMANDER V:
1
2
3
4
5

Quick Links

See also: Installation Instructions & Owner's Manual, Instruction and Installation Manual
2009-2011 Polaris Sportsman 850
I n s t a l l a t i o n I n s t r u c t i o n s
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
19-005
www.powercommander.com
2191 Mendenhall Drive North Las Vegas, NV 89081 (800) 992-4993 www.powercommander.com
PARTS LIST
1
Power Commander
1
USB Cable
1
Installation Guide
2
Power Commander Decals
2
Dynojet Decals
2
Velcro strips
1
Alcohol swab
THE IGNITION MUST BE TURNED
OFF BEFORE INSTALLATION!
THE LATEST POWER COMMANDER
SOFTWARE AND MAP FILES CAN BE
DOWNLOADED FROM OUR WEB SITE AT:
www.powercommander.com
2009-2011 Polaris Sportsman 850 - PCV - 1
loading

Related Manuals for Dynojet POWER COMMANDER V

Summary of Contents for Dynojet POWER COMMANDER V

  • Page 1 Installation Guide 2009-2011 Polaris Sportsman 850 Power Commander Decals I n s t a l l a t i o n I n s t r u c t i o n s Dynojet Decals Velcro strips Alcohol swab THE IGNITION MUST BE TURNED OFF BEFORE INSTALLATION!

  • Page 2: Usb Connection

    POWER COMMANDER V INPUT ACCESSORY GUIDE ACCESSORY INPUTS Map - (Input 1 or 2) The PCV has the ability to hold 2 different base maps. You can switch on the fly between these two base maps when you hook up a switch to the MAP inputs. You can USB CONNECTION use any open/close type switch. The polarity of the wires is not important. When using the Autotune kit one position will hold a base map and the other position will let you activate the learning mode. When the switch is “CLOSED” Autotune will be activated. (Set to Switch Input #1 by default.) Shifter- (Input 1 or 2) These inputs are for use with the Dynojet quickshifter. Insert the wires from the CRANK Dynojet quickshifter into the SHIFTER inputs. ANALOG The polarity of the wires is not important. (Set to Switch Input #2 by default.) SPEED EXPANSION PORTS 1 & 2 INPUT 2 (Grnd)
  • Page 3 FIG.A Remove the seat and left side panel. Install the PCV on top of the stock ECU using the supplied velcro (Fig. A). Make sure to clean both surfaces before attaching with the alcohol swab. FIG.B Unplug the stock wiring harness from the Throttle Position Sensor (Fig. B). Unplug The TPS is located on the front side of the throttle bodies. FIG.C Plug the 3-pin connectors of the PCV in-line of the stock TPS and wiring harness (Fig. C). 19-005 www.powercommander.com 2009-2011 Polaris Sportsman 850 - PCV - 3...
  • Page 4 FIG.D Unplug the stock wiring harness from each injector (Fig. D). FIG.E Plug the PCV in-line of the stock wiring harness and injectors (Fig. E). Connect the ORANGE colored wires of the PCV to the front cylinder. FIG.F FOLLOW THESE STEPS FOR THE 2009-2010 MODELS. FOR THE 2011 MODEL GO TO STEP 9 Route the ground wire of the PCV along the left hand frame rail and go to the battery at the rear of the ATV (Fig. F). 19-005 www.powercommander.com 2009-2011 Polaris Sportsman 850 - PCV - 4...
  • Page 5 FIG.G Ground Attach the ground wire of the PCV to the ground bolt near the battery (Fig. G). FIG.H FOLLOW THESE STEPS FOR THE 2011 MODEL Remove the battery access cover on the front of the ATV. Ground 10 Attach the ground wire of the PCV to the ground bolt near the brake reservoir (Fig. H). 11 Reinstall the seat and side cover. 19-005 www.powercommander.com 2009-2011 Polaris Sportsman 850 - PCV - 5...