Alternative Mode Programming - Honeywell AlarmNet 7845i-GSM Installation And Setup Manual
Internet communication
Hide thumbs
Also See for AlarmNet 7845i-GSM:
- Quick setup manual (1 page) ,
- Installation manual (2 pages) ,
- Quick manual (2 pages)
Table of Contents
used. In some control panels, it is called "relay programming" and in others it is called "output
device programming." It is recommended that "close and stay closed" (usually choice 2) action
is selected. Selection of momentary activation will cause the 7845i-GSM to generate an alarm
and NOT a restore, even if the 7845i-GSM is programmed to send a restore for the given zone.
In 4204 mode, messages are reported in ADEMCO High-Speed format. Zone alarms
(status 7) are reported with "1" (alarm) or "3" (restore) displayed in the zone position for the
respective zone (e.g. alarm on zone 2: 5155 5555 7; restore 5355 5555 7). A supervision fault
trouble message is automatically sent if the module detects no activity on its connection to
the control. The message is: 5555 5515 5; restore message is: 5555 5535 5.
Refer to Table 5 for 4204 Emulation Mode programming and follow the prompts that pertain
to 4204 or Two-4204 mode. A check mark (
mode.
Alternative Mode Programming
Press the [ENTER] key to begin programming
operation being programmed.
NOTE: The central station can remotely block access to
Table 5: Programming a 7845i-GSM for Zone Trigger, 4204 Emulation, or Two-4204 Emulation modes.
PROMPTS
Strt Prog Mode?
1
Y/N_
Enter Password
2
Program 7845?
3
Y/N_
Create Password?
4
Y/N_
Change Password?
5
Y/N_
Enter Password
6
local device programming. If this has been done,
the following prompt appears:
4204/
ZONE
ENTRY
2-4204
TRIG.
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
Section 3: Programming the 7845i-GSM
✔
) indicates whether the prompt applies to that
ollow the prompts for the mode of
and f
Access to Prog
Mode Denied
OPTIONS
Enters programming mode.
[Y], [N]
[0-9, A-F, N,
If a password has been previously assigned, this
S, T, X, Y]
prompt appears.
Enter a 4-digit password (0-9, A-F, N, S, T, X, Y).
The next prompt appears.
[Y], [N]
To begin programming the module, press [Y] and go
to Prompt 9: "Device Mode."
To create a password if none has been assigned,
press [N] and go to Prompt 4: Create Password.
To change an existing password, press [N] and go
to Prompt 5: "Change Password."
[Y], [N]
Passwords can be used to protect account and
programming information.
If no password has been assigned, this prompt
appears after pressing [N] at the "Program 7845?"
prompt.
If a password is desired, press [Y] and go to Prompt
6: "Enter Password."
If a password has already been assigned, this
[Y], [N]
prompt appears after pressing [N] at the "Program
7845?" prompt.
Press [Y] if you want to change the password.
NOTE: To clear an existing password, without
entering a new one, answer [Y] to the "Change
Password?" prompt, then press the [Enter] key
when prompted for the new password and its
confirmation.
[0-9, A-F, N,
This prompt is displayed if [Y] was pressed in
S, T, X, Y]
Prompt 4 or 5.
Enter a 4-digit password (0-9, A-F, N, S, T, X, Y).
DESCRIPTION
3-9
Hide quick links:
Table of Contents
