Menu 7: Analog I/O - Emerson unidrive sp User Manual
Universal variable speed ac drive for induction and servo motors
Hide thumbs
Also See for unidrive sp:
- User manual (268 pages) ,
- User manual (310 pages) ,
- Technical note (6 pages)
Table of Contents
Parameter
Keypad and
Menu 7
structure
display
5.9
Menu 7: Analog I/O
Hardware
The drive has three analog inputs (AI1 to AI3) and two analog outputs (AO1 and AO2). Each input has a similar parameter structure and each output
has a similar parameter structure. The nominal full scale level for inputs in voltage mode is 9.8V. This ensures that when the input is driven from a
voltage produced from the drive's own 10V supply, the input can reach full scale.
Terminal
Input
5/6
AI1
7
AI2
8
AI3
Terminal
Output
9
AO1
10
AO2
Update rate
The analog inputs are sampled every 4ms except where the destinations shown in the table below are chosen, the input is in voltage mode and other
conditions necessary for short cutting are met.
Input destination
Pr 1.36 - Analog reference
Pr 1.37 - Analog reference
Pr 3.10 - Power feed forward compensation
Pr 3.22 - Hard speed reference
Pr 4.08 - Torque reference
It should be noted that the analog inputs are always sampled every 4ms in Open-loop mode. However, the window filter applied to analog input 1 (see
Pr 7.26) can be set to a time that is shorter than 4ms. There is no advantage in doing this, as it simply reduces the resolution of the input data, which
is still only sampled and routed to its destination parameter every 4ms.
Analog outputs are updated every 4ms except when one of the following is the source and high speed update mode is selected. In high speed mode
the output operates in voltage mode, is updated every 250μs, special scaling is used as described in the table and the user scaling is ignored.
Output source
Pr 3.02 – speed
Pr 4.02 - torque prod current
Pr 4.17 - magnetising current
Pr 5.03 - output power
150
Parameter
Parameter
x.00
description format
Input modes
Voltage only
(16 bit plus sign as a speed reference)
0 to 6
0 to 9
Output modes
Resolution
0 to 3
10 bit plus sign
0 to 3
10 bit plus sign
Closed-loop vector or Servo mode sample rate
250μs
(AI1 subject to window filter. See Pr 7.26 on page 159)
250μs
(AI1 subject to window filter. See Pr 7.26 on page 159)
250μs
(AI1 subject to window filter. See Pr 7.26 on page 159)
AI1 – 4ms
AI2 or 3 – 250μs
(Closed-loop vector and servo modes only)
10.0V = SPEED_MAX
10.0V = Kc / 0.45
where Kc is the current scaling factor for the drive
10.0V = Kc / 0.45
(Closed-loop vector and servo modes only)
The output is the product of the active current and the voltage component in phase with the
active current (vsy x isy).
10V would be produced when:
Active current = Kc / 0.45
Peak phase voltage in phase with the active current = DC_VOLTAGE_MAX / 2
www.controltechniques.com
Advanced parameter
Macros
descriptions
Resolution
12 bit plus sign
10 bit plus sign
10 bit plus sign
Scaling
Serial comms
Electronic
Performance RFC mode
protocol
nameplate
Regen mode sample rate
AI1 - 4ms
AI2 or 3 - 1ms
Unidrive SP Advanced User Guide
Issue Number: 10
- Quick Links:
- Alarm and Trip Display
Hide quick links:
Table of Contents
