Table of Contents
A.6
Index
A
Acceleration bipolar, 4–6
Amplifier warning temperature, 4–6
Analog measuring outputs, 4–13
Analog output of parameter values, 4–13
Automatic/manual mode, 4–12
B
Backup, 4–20
Band stop, 4–18
Band stop configuration, 4–18
Bipolar speed limit value, 4–6
Bipolar torque limit value, 4–6
Block diagram, 4–17
Braking resistors, 4–8
C
CAN bus, connection, A–1
CAN LED, 2–10
Cannon connector, CAN bus, A–1
Changing over the parameter set, 4–11
Changing phases, 3–8
Checking the hardware, 2–2
Clock Start time, 2–8
Commissioning
Initial, 4–1
Series, 5–1
Communication, between the drive and DSS, 2–5
Communication between rho and drive, 2–8
Communication error F10, 3–8
Configuration of inputs, 4–8
Configuration of outputs, 4–8
Configuring the CAN interface, 2–4
Connection, DSS to drive, 2–5
Cycle time, 2–8
D
Diagnoses, 6–1
Diagrams, cyclic, 6–5
Display control word CANrho, 6–5
Display status word CANrho, 6–5
Displaying data, cyclic, 6–2
in separate window, 6–6
parameter definition, 6–3
updating frequency, 6–3
Displaying I/O signals, 6–4
Documentation, 1–7
Documenting the parameters of a drive, 6–7
Download parameter list, 4–3
Drive
Display configuration, 6–1
Displaying the status, 6–2
ON, Enable, Start, 6–2
DSS, initialize, 2–7
DSS monitor, 3–3
Load file, 3–3
Save file, 3–4
1070 066 037-101 (00.02) GB
E
EMC Directive, 1–1
EMC product standard, 1–1
EMERGENCY–STOP circuit, Check functioning, 2–3
EMERGENCY–STOP devices, 1–5
Enable signal, external, 4–7
Errors, resetting, 3–10
ESD
Electrostatic discharge, 1–6
grounding, 1–6
workplace, 1–6
ESD–sensitive components, 1–6
Establish connection, Drive–DSS, 2–6
Establishing connection, Drive–rho, 2–10
Exit the DSS program, 3–1
F
F06 error message on H1, 4–13
F10 error message on H1, 3–8
F13 fault message on H1, 4–6
FEPROM
Backup, 4–1, 4–20
copy to the RAM, 3–10
Filling in a template, 6–7
Filter configuration, 4–18
Firmware version, 6–1
Floppy disk drive, 1–7
G
Grounding bracelet, 1–6
H
Halting mode, 4–7
Hard disk drive, 1–7
Holding brake
Check control logic, 2–3
Controlling via OUT3, 4–8
I
IDN Backup, of the original parameters, 4–1
IDN backup, 4–20
Initial commissioning, 4–1
Initializing, DSS, 2–7
Inport, 4–8
Interface
Configuring CAN, 2–4
disconnect connection cable, 2–7
setting parameters for RS–232, 2–5
X51, 2–4
L
LED "CAN", 2–10
Load file, into the DSS monitor, 3–3
Low pass, 4–18
Low–Voltage Directive, 1–1
Appendix
A–5
Table of Contents
