Emerson IEC 62591 Instruction Manual
  1. Manuals
  2. Brands
  3. Emerson Manuals
  4. Recording Equipment
  5. IEC 62591
  6. Instruction manual
Emerson IEC 62591 Instruction Manual

Emerson IEC 62591 Instruction Manual

Wireless interface. for roc800-series and floboss 107
Hide thumbs Also See for IEC 62591:
Table of Contents

Quick Links

Part Number D301708X012
June 2018
IEC 62591 Wireless Interface Instruction
Manual (for ROC800-Series and FloBoss™
107)
Remote Automation Solutions
Table of Contents
loading

Related Manuals for Emerson IEC 62591

Summary of Contents for Emerson IEC 62591

  • Page 1 Part Number D301708X012 June 2018 IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss™ 107) Remote Automation Solutions...
  • Page 2 Our full-time professional instructors can conduct classroom training at several of our corporate offices, at your site, or even at your regional Emerson office. You can also receive the same quality training via our live, interactive Emerson Virtual Classroom and save on travel costs. For our complete schedule and further information, contact the Remote Automation Solutions Training Department at 800-338-8158 or email us at [email protected].

  • Page 3: Table Of Contents

    IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) Contents Chapter 1 – General Information Scope of Manual ..........................1-2 Hardware ............................1-2 1.2.1 IEC 62591 Wireless Interface Module ................1-2 1.2.2 Emerson Wireless 781 Field Link ..................1-3 1.2.3...
  • Page 4 IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) Errors from the IEC 62591 Transmitter Tab ..................4-3 4.3.1 NaN value ........................... 4-3 4.3.2 Stale / Communication Failure .................... 4-4 Appendix A – Glossary Index Revised June-2018...

  • Page 5: Chapter 1 - General Information

    IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) Chapter 1 – General Information In This Chapter Scope of Manual ..................1-2 Hardware ....................1-2 1.2.1 IEC 62591 Wireless Interface Module ........1-2 1.2.2 Emerson Wireless 781Field Link ..........1-3 1.2.3 WirelessHART Field Devices .............

  • Page 6: Scope Of Manual

    IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) Figure 1-1. IEC 62591 Field Installation 1.1 Scope of Manual This manual contains the following chapters: Chapter 1 Provides an overview of the hardware for the IEC General Information 62591 Wireless Interface.

  • Page 7: Emerson Wireless 781 Field Link

    IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) Figure 1-2. IEC 62591 Wireless Interface Module You can place the module in any available slot on the ROC800 and in any available slot on the FB107. However, each ROC800 or FB107 can support only one IEC 62591 Wireless Interface module.

  • Page 8: Wirelesshart Field Devices

    Wireless Interface provide you with the ability to manage signals from a network of WirelessHART field devices. The physical configuration of the IEC 62591 Wireless Interface is based on the controller (FB107 or ROC800) and the total number of field devices. A ROC800 implementation supports up to 60 devices, while a FB107 implementation supports up to 20 devices.

  • Page 9: Additional Technical Information

    IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) Once you have installed the IEC 62591 modules and wired them to the Field Link, you use Field Tools to configure and then commission (“activate”) the entire network. Refer to Chapter 3, Configuring and Commissioning, for specific instructions.
  • Page 10 IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) [This page is intentionally left blank.] General Information Revised June-2018...

  • Page 11: Chapter 2 - Installation

    Wiring the Module and Field Link ............ 2-5 2.3.1 Wiring the Field Link ............. 2-5 2.3.2 Wiring the IEC 62591 Module to the Field Link ....2-6 Preparing for Configuration and Commissioning ......2-7 This chapter describes installing the IEC 62591 module in either a ROC800 or FB107, installing the Field Link, and connecting the Field Link to the IEC 62591 Wireless Interface module.
  • Page 12 ▪ If the slot is currently empty, remove and store the module cover. : When you install an IEC 62591 module in the FB107’s slot Note 2, the firmware redirects the COM2 communications port on the CPU to the module installed in slot 2.

  • Page 13: Installing The Field Link

    IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) Insert the module in the slot on the base unit or expansion rack, making sure that the module faces the correct direction (see Figure 1-2). Gently slide the module into place until it contacts properly with the connectors on the backplane.

  • Page 14: Positioning The Antenna

    IEC 62591 Wireless Interface Instruction Manual (ROC800-Series and FloBoss 107) 2.2.2 Positioning the Antenna Position the antenna vertically, either straight up or straight down, approximately 1 m (3 ft) from any large structure, building, or conductive surfaces to allow clear communication with other devices.

  • Page 15: Grounding The Field Link

    IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) Figure 2-3. Field Link Mounting 2.2.4 Grounding the Field Link For further information on grounding the field link, refer to the documentation that accompanied the device (Emerson™ Wireless 781 Field Link Quick Installation Guide, part 00825-0100-4421) 2.3 Wiring the Module and Field Link...

  • Page 16: Wiring The Iec 62591 Module To The Field Link

    Since the ROC800 and FB107 modules use the same PCB, you wire the modules to the Field Link in the same way. Figure 2-5 shows wiring for the FB107 IEC 62591 module; Figure 2-6 shows wiring for the ROC800 IEC 62591 module.

  • Page 17: Preparing For Configuration And Commissioning

    IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) Figure 2-5. FB107 IEC 62591 Module Power and Data Wiring to Field Link Figure 2-6. ROC800 IEC 62591 Module Power and Data Wiring to Field Link 2.4 Preparing for Configuration and Commissioning...
  • Page 18 IEC 62591 Wireless Interface Instruction Manual (ROC800-Series and FloBoss 107) [This page is intentionally left blank.] Installation Revised June-2018...

  • Page 19: Chapter 3 - Configuration And Commissioning

    3.4.1 Updating the IEC 62591 Module Firmware (ROC800/FloBoss 107) ............ 3-40 After you have wired the Field Link to the IEC 62591 module and applied power to the module, you use the AMS Device Configurator to configure transmitters for the wireless network. You then use ROCLINK 800 to activate (or “commission”) each WirelessHART...

  • Page 20: Overview

    As indicated previously, a wireless interface network consists of a number of wireless devices (up to 60 in a ROC800-based network or up to 20 in an FB107-based network), a Field Link, and an IEC 62591 module installed in an FB107 or ROC800. For the configuration and commissioning tasks described in this chapter, we’ve added a PC...

  • Page 21: Network Id And Join Key

    IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) Notes ▪ Tag names cannot exceed 32 characters, and tag names must be unique to the wireless network. ▪ Use upper-case (capital) letters for tags names; this corresponds to how the program internally stores tag names.

  • Page 22: Iec 62591 Module Interface (Fb107)

    IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) 3.2 IEC 62591 Module Interface (FB107) The FB107 automatically recognizes the IEC62691 module when you install it and adds it to the graphical interface. When you click on the...
  • Page 23 IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) Description Integrity Displays any integrity problems with the wireless network. Note: If a transmitter has a problem, this field turns red and displays a message identifying the transmitter at fault (here, the transmitter in logical position 2).
  • Page 24 IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) : The values initially shown in the Network ID and Join Key Note fields in Figure 3-3 are default values. You must change these to your network-specific ID and join keys and save the configuration to flash memory.
  • Page 25 IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) ▪ Configuring Network. The code is running and the module is attempting to pull configuration info from the RTU. If the Initializing status is taking too long, it means that either ▪...

  • Page 26: Commissioning Devices

    IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) The following sections discuss how to use these tabs to manage your network. 3.2.1 Commissioning Devices You use the Commission tab to individually or collectively commission devices. Figure 3-5. Commission tab This screen has two lists, Uncommissioned and Commissioned.
  • Page 27 IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) ▪ The device does not disappear from the Uncommissioned List until communication issues have been resolved. The number of rows on the Commission screen correlates to the number of wireless devices your controller supports. Each row represents a specific logical position.

  • Page 28: Managing Device Information

    IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) : Remember to adjust or redefine any TLPs you have designated Note to accumulate the information for the decommissioned device’s logical position. Replacing a Device If a particular wireless device in your network stops working, you can easily replace it with a similar device.
  • Page 29 IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) Figure 3-8. Transmitter screen Notes ▪ You can also double-click a commissioned device on the Commission screen to immediately access the Transmitter screen for that device. ▪ If you use ROCLINK to change transmitter values when the transmitter is busy with other communications tasks, the transmitter may fail to update and reverts to previous values.
  • Page 30 IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) Field Description Transmitter This section displays read-only information reported Information by the transmitter, including serial number, manufacturer ID, type of device, battery life, and other data. Note: Battery life is calculated by the transmitter.
  • Page 31 IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) Field Description Process Variables Displays the value, health, and status for the primary (PV), secondary (SV), tertiary (TV), and quaternary (QV) dynamic variables. For each variable, two status fields display to the right of the Value field.
  • Page 32 IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) Field Description Discrete Variables Sets the configuration and shows the status of connected discrete devices that support discrete variables. The IEC 62591 module can control a maximum of four discrete variables that display in a list in the Discrete Variables field.
  • Page 33 IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) Field Description Falling Publishes updates at the interval set in the Min Update Time field when the source value falls below the value set in the Trigger Level field. Updates are published at the Min Update Time until the value rises above the threshold.
  • Page 34 IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) Field Description HART Command This read-only field shows an indicator when the Execution Status IEC 62591 module sends a HART command to the sensor, and that command is unsuccessful. Each bit...

  • Page 35: Viewing Network Statistics

    IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) Field Description Publish Time Sets the time interval (in seconds) at which the HART device publishes its events. Note: This value must be less than or equal to the value you set in the Maximum Update Time field.
  • Page 36 IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) transmitters and is updated every ten seconds. Select the Statistics tab to view this information. : Refer to the transmitter's manufacturer for more information Note about the fields on this tab.
  • Page 37 IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) Field Description This read-only field shows the number of Messages Received messages IEC62591 module has received from the Field Link. Message Nacks This read-only field shows the number of NACKs Transmitted the IEC62591 module has sent to the Field Link.

  • Page 38: Retrieving A Diagnostic Log

    Click to reset all values on this tab. 3.2.4 Retrieving a Diagnostic Log The IEC 62591 module has a USB port which you can use to retrieve a diagnostic log to assist in troubleshooting. Select the Diagnostics tab to display the Diagnostics screen:...

  • Page 39: Displaying Commissioned Transmitters

    Set Logging Severity X COMPLETED, where X represents the severity you have selected. 3.2.5 Displaying Commissioned Transmitters From the main IEC 62591 module screen, you can display and quickly access transmitter-specific information. Select the Transmitter tab to display the Transmitter screen.

  • Page 40: Iec 62591 Module Interface (Roc800)

    Figure 3-7) for that device. 3.3 IEC 62591 Module Interface (ROC800) To access the screens you use to configure and commission the network: Start ROCLINK 800 and click the IEC 62591 module on the graphical interface. The IEC 62591 Module screen displays: 3-22...
  • Page 41 IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) Figure 3-12. IEC 62591Module The module has six tabs: Description Module Provides read-only statistical information about the IEC 62591 module, such as serial number and part numbers. Network Defines the Join Key and Network ID for the network.

  • Page 42: Accessing The Network

    IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) Description Describes how to use the module’s USB port to Diagnostics generate log information for resolving issues. The following sections discuss how to use these tabs to manage your network.
  • Page 43 IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) Field Description Enter a five-character Network ID. Valid values are Network ID 1 to 36863. Should be noted that each IEC62591 Module / RTU can only have a single Network ID. The "grouping"...

  • Page 44: Commissioning Devices

    IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) ▪ On-Line. When the Status field shows On-line, you can begin commissioning devices for the network. Proceed to Commissioning Devices. 3.3.2 Commissioning Devices When you select the Commission tab, ROCLINK 800 displays the Commission screen (see Figure 3-16).
  • Page 45 IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) ▪ Select the device and “drag” it to a position on the Commissioned list. The number of rows on the Commission screen correlates to the number of wireless devices your controller supports. Each row represents a specific logical position.
  • Page 46 IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) Figure 3-16. Commissioned Device Another indicator that the device has been successfully commissioned is the activation of the Transmitter tab. : If you change the tag for a transmitter using either a hand-held...

  • Page 47: Managing Device Information

    IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) device. This tells ROCLINK 800 that you want this new device to assume all the defined characteristics of the old device. ROCLINK 800 displays a verification dialog to prevent you from accidentally replacing a device: Figure 3-12.
  • Page 48 IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) Notes ▪ You can also double-click a commissioned device on the Commission screen to immediately access the Transmitter screen for that device. ▪ If you use ROCLINK to change transmitter values when the transmitter is busy with other communications tasks, the transmitter may fail to update and reverts to previous values.
  • Page 49 IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) Field Description Commission Status Indicates the current status of the device in the commissioning process. Valid values are: 0 = Logical Not Used 1 = Configuring Burst Command 2 = Configuring Burst Variables...
  • Page 50 IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) Field Description Sets the configuration and shows the status of Discrete Variables connected discrete devices that support discrete variables. The IEC 62591 module can control a maximum of four discrete variables that display in a list in the Discrete Variables field.
  • Page 51 IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) Field Description Falling Publishes updates at the interval set in the Min Update Time field when the source value falls below the value set in the Trigger Level field. Updates are published at the Min Update Time until the value rises above the threshold.
  • Page 52 IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) Field Description HART Command This read-only field shows an indicator when the Execution Status IEC 62591 module sends a HART command to the sensor, and that command is unsuccessful. Each bit...

  • Page 53: Viewing Network Statistics

    IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) Field Description Publish Time Sets the time interval (in seconds) at which the HART device publishes its events. Note: This value must be less than or equal to the value you set in the Maximum Update Time field.
  • Page 54 IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) transmitters and is updated every ten seconds. Select the Statistics tab to view this information. : Refer to the transmitter's manufacturer for more information Note about the fields on this tab.
  • Page 55 IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) Field Description This read-only field shows the number of Messages Received messages IEC62591 module has received from the Field Link. Message Nacks This read-only field shows the number of NACKs Transmitted the IEC62591 module has sent to the Field Link.

  • Page 56: Retrieving A Diagnostic Log

    Click to reset all values on this tab. 3.3.5 Retrieving a Diagnostic Log The IEC 62591 module has a USB port which you can use to retrieve a diagnostic log to assist in troubleshooting. Select the Diagnostics table to display the Diagnostics screen: Figure 3-19.

  • Page 57: Updating Module Firmware

    3.4 Updating Module Firmware You can also use the USB port on the IEC 62591 module to upgrade the firmware on the module. To access this option, select Utilities > Update Firmware on the ROCLINK 800 main menu bar. The Update Firmware screen displays.

  • Page 58: Updating The Iec 62591 Module Firmware (Roc800/Floboss 107)

    IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) Figure 3-21. IEC 62591 Module Firmware Update screen Follow the procedures on this screen to update the firmware in the IEC 62591 module. : The value in the Current Version field changes when the Note firmware update completes.
  • Page 59 IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) Figure 3-22. Attaching a USB drive 2. Create a folder named “upgrade” in the root directory. Figure 3-23. Creating the upgrade folder 3. Copy the upgrade file (ras-wihart-1.10-release.zip) to the Upgrade folder on the USB drive.
  • Page 60 IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) Figure 3-24. Copying the upgrade file 4. Start ROCLINK. Figure 3-25. Starting ROCLINK 5. Click on the IEC 62591 module to verify that it is running. The System Mode field should contain “Run Mode.” 3-42 Configuration and Commissioning...
  • Page 61 IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) Figure 3-26. Verifying Run Mode 6. Verify that the module is connected to the network and that the module is currently on-line. Figure 3-27. Verifying Online status Remove the USB drive for your PC’s USB port and attach it to the USB port on the IEC 62591 module.
  • Page 62 IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) 8. Select the IEC 62591 Module tab and verify that the Current Version is 1.00. Click Start to begin the update process. Figure 3-29. Verifying current version 9. When the dialog displays, click Yes to start the update process.
  • Page 63 IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) Figure 3-31. Status message: Waiting for upgrade to start 11. Once the update starts, it takes several minutes to complete. Status messages continue to display at the bottom of the screen.
  • Page 64 IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) Figure 3-33. Status message: Waiting for module to reboot 13. When the firmware update finishes, a dialog displays. Click OK to continue. Figure 3-34. Firmware update completed dialog box 14.
  • Page 65 IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) 15. The update process preserves the network settings for your module, but you should still verify that the settings are correct. Click Cancel to close the Update Firmware screen, click on the IEC 62591 module, and select the Network tab to review the network settings.
  • Page 66 IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) [This page is intentionally left blank.] 3-48 Configuration and Commissioning Revised June-2018...

  • Page 67: Chapter 4 - Troubleshooting

    4.2.3 Looking for Possible Configuration Errors ......4-2 4.2.4 Rebooting after a Power Loss ..........4-3 4.2.5 USB Flash Drive Not Recognized ........4-3 Errors from the IEC 62591 Transmitter Tab ........4-3 4.3.1 NaN value ................4-3 4.3.2 Stale / Communication Failure ..........4-4 This chapter provides generalized guidelines for troubleshooting the IEC62591 module and the Field Link.

  • Page 68: Common Troubleshooting Techniques

    ▪ Field Communicator (optional) For software you have: ▪ The IEC 62591 application running in ROCLINK 800 ▪ IEC 62591 protocol software running in the Field Link and in all of the wireless devices 4.2.2 Conducting Basic Hardware Checks ▪ Ensure power is connected.

  • Page 69: Rebooting After A Power Loss

    ▪ Did you assign a unique Long Tag Name to each wireless device and specify the exact same long tag names in the IEC 62591 application? ▪ Did you assign a Network ID which must be the same in each and every...

  • Page 70: Stale / Communication Failure

    IEC62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) Figure 4-1. NaN warning in Transmitter tab) When NaN is reported, the RTU supports a failsafe operation defined by the user (Retain Last Value, Use Failsafe Value). Figure 4-2. User-defined failsafe operation 4.3.2 Stale / Communication Failure If the RTU reports a Stale or Communication Failure status in the Communication Status field, interrogate the transmitter using...
  • Page 71 Analog to Digital signal conversion. Acrylonitrile Butadiene Styrene. Active A mode in which the IEC 62591 module sends messages to the wireless network to Advertising keep radios active for a longer period of time to facilitate quicker detection of new (or replaced) wireless devices.
  • Page 72 IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) (continued) C1D2 Class 1, Division 2 hazardous area CMOS Complementary Metal Oxide Semiconductor, a type of microprocessor used in a ROC. Coil Digital output, a bit to be cleared or set.
  • Page 73 IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) (continued) Download The process of sending data, a file, or a program from a PC to a ROC. Differential Pressure. Data Set Ready modem communications signal. Data Terminal Equipment.
  • Page 74 IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) (continued) Foot or feet. Function Sequence Table, a type of user-written program in a high-level language designed by Remote Automation Solutions. Ground Fault Analysis. Electrical ground, such as used by the ROC’s power supply.
  • Page 75 IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) Liquid Crystal Display. Local Display Panel, a display-only device that plugs into ROC300-Series units (via a parallel interface cable) used to access information stored in the ROC. Light-Emitting Diode.
  • Page 76 IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) On-line Accomplished while connected (by a communications link) to the target device. For example, “on-line configuration” refers to configuring a ROC800-Series unit while connected to it, so that you can view the current parameter values and immediately load new values.
  • Page 77 IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) (continued) Random Access Memory. RAM is used to store history, data, most user programs, and additional configuration data. Report-by-exception. RBX always refers to Spontaneous RBX in which the ROC contacts the host to report an alarm condition.
  • Page 78 IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) (continued) Signal Value Analog. Stored in the Results Register, it is the analog value that is passed between functions in an FST. Signal Value Discrete. Stored in the Compare Flag, it is the discrete value that is passed down the sequence of functions in an FST.
  • Page 79 IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) Index 3-21. IEC 62591 Firmware Update (ROC800) ..........3-36 3-22. Attaching a USB drive ......3-37 Adding the join key ........... 3-21 3-23. Creating the upgrade folder ....3-37 3-24.
  • Page 80 IEC 62591 Wireless Interface Instruction Manual (ROC800-Series and FloBoss 107) Updating firmware IEC 62591 module....3-36 USB port ..............1-3 Wiring ..............2-5 Index Revised June-2018...
  • Page 81 IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) [This page is intentionally left blank.] Revised June-2018 Index...
  • Page 82 IEC 62591 Wireless Interface Instruction Manual (for ROC800-Series and FloBoss 107) For customer service and technical support, visit www.Emerson.com/SupportNet. Global Headquarters, North America, and Latin America: Emerson Automation Solutions Remote Automation Solutions 6005 Rogerdale Road Houston, TX 77072 U.S.A. T +1 281 879 2699 | F +1 281 988 4445 www.Emerson.com/RemoteAutomation...

Table of Contents