Page 1
Installation and Setup Guide 020-103584-02 CP2415-Xe...
Page 2
Christie's control such as maintenance of the product in proper working conditions. Performance specifications are based on information available at the time of printing. Christie makes no warranty of any kind with regard to this material, including, but not limited to, implied warranties of fitness for a particular purpose.
Introduction This manual is intended for qualified installers and trained operators of Christie CP2415-Xe projection systems. Product documentation For installation, setup, and user information, see the product documentation available on the Christie website. Read all instructions before using or servicing this product.
• SHOCK HAZARD! A dedicated, protected ground or earth wire must be installed on the product by Christie qualified technicians or electricians before it can be connected to power. • TRIP OR FIRE HAZARD! Position all cables where they cannot contact hot surfaces, be pulled, be tripped over, or damaged by persons walking on or objects rolling over the cables.
Learn about the labels that may be used on the product. Labels on your product may be yellow or black and white. General hazards Hazard warnings also apply to accessories once they are installed in a Christie product that is connected to power. Fire and Shock Hazard To prevent fire or shock hazards, do not expose this product to rain or moisture.
Projector overview The Christie CP2415-Xe is a compact digital cinema projector suited for theaters with screens up to 15 meters (50 feet), where booth space is at a premium. The Christie CP2415-Xe is a robust and reliable projector that features a motorized lensing solution and a selection of eight zoom lenses to guarantee an image projection solution for virtually any auditorium.
Dealer or Christie Sales/Service contact phone number: Serial number: The serial number can be found on the license label located on the display panel. Purchase date: Installation date: Technical support Technical support for Christie Cinema products is available at: • [email protected] • +1-877-334-4267 •...
Installation and setup Learn how to install, connect, and optimize the projector. This section provides detailed information on projector setup. Site requirements To safely install and operate the CP2415-Xe projectors, the installation location must meet these minimum requirements. Physical operating environment •...
3. Center the lens parallel with the screen to make sure optimum lens performance with minimal offset. If this position is not possible, Christie recommends relying on offset rather than extra tilt. 4. Use a protractor to measure the degree of screen tilt and extend or retract the projector feet to match this angle.
• EXPLOSION HAZARD! Always wear protective safety clothing (gloves, jacket, face shield) approved by the manufacturer whenever the lamp door is open or when handling the lamp. Any local or federal specifications take precedence over Christie's protective clothing recommendations. •...
The protected earth wire must be green/yellow 12 AWG minimum. Use a 20A branch circuit breaker for Input A or 200-240 V main inlet. The dedicated protected earth wire can only be installed by a Christie accredited service technician or an electrician.
In the left navigation menu, select Lamp Settings > LampLOC. b) Select Auto Align. Disposing of the product packaging Once the product has been installed and set up, Christie recommends reusing or recycling the product packaging according to your local regulations. CP2415-Xe Installation and Setup Guide 020-103584-02 Rev.
2. Select Auto LampLOC. Calibrating the Intelligent Lens System On CP2415-Xe projectors, the Intelligent Lens System (ILS) is activated by default. Use the Auto Calibrate feature of the ILS to find and compensate for motor backlash, and to determine the movement range for the currently installed lens.
2. If the keystone effect is severe, unevenly adjust the feet to compensate for projector tilt. Christie recommends using the lens offset to align the center of the image to the center of the screen before correcting the keystone effect.
Learn how to adjust the top and bottom (vertical) boresight. Warning! If not avoided, the following could result in death or serious injury. • This procedure must be performed by Christie qualified technicians. Caution! If not avoided, the following could result in minor or moderate injury. •...
Warning! If not avoided, the following could result in death or serious injury. • UV EXPOSURE! Protective UV safety glasses with side shields and protective safety clothing approved by Christie must be worn when performing optical adjustments or servicing the product. 1. Display a full white field test pattern.