1. Manuals
  2. Brands
  3. Panasonic Manuals
  4. Remote Control
  5. CZ-RWSU2
  6. Installation instructions manual

Panasonic CZ-RWSU2 Installation Instructions Manual

Hide thumbs Also See for CZ-RWSU2:
Table of Contents

Quick Links

See also: Instruction Manual
INSTALLATION INSTRUCTION
INSTRUCTIONS D'INSTALLATION
BEDIENUNGSANLEITUNG
ISTRUZIONI DI INSTALLAZIONE
INSTRUÇÕES DE INSTALAÇÃO
ΟΔΗΓΙΕΣ ΕΓΚΑΤΑΣΤΑΣΗΣ
INSTRUCCIONES DE INSTALACIÓN
Save these instructions!
Conservez précieusement ces instructions !
Diese Anleitung aufbewahren!
Conservare le presenti istruzioni!
Guarde estas instruções!
Φυλάξτε αυτές τις οδηγίες!
¡Guarde estas instrucciones!
85464369341021
CZ-RWSU2
CZ-RWST2
CZ-RWSL2
CZ-RWSC2
Wireless Remote Control System
Système de télécommande à infrarouge
Kabellose Fernbedienung
Sistema di Telecomando senza fi l
Sistema de telecomando sem fi os
Ασύρματο Σύστημα Τηλεχειρισμού
Sistema de control remoto inalámbrico
EN
FR
DE
IT
PT
GR
ES
Table of Contents
loading

Related Manuals for Panasonic CZ-RWSU2

Summary of Contents for Panasonic CZ-RWSU2

  • Page 1 Sistema di Telecomando senza fi l INSTRUÇÕES DE INSTALAÇÃO Sistema de telecomando sem fi os ΟΔΗΓΙΕΣ ΕΓΚΑΤΑΣΤΑΣΗΣ Ασύρματο Σύστημα Τηλεχειρισμού INSTRUCCIONES DE INSTALACIÓN Sistema de control remoto inalámbrico CZ-RWSU2 CZ-RWST2 CZ-RWSL2 CZ-RWSC2 Save these instructions! Conservez précieusement ces instructions ! Diese Anleitung aufbewahren! Conservare le presenti istruzioni! Guarde estas instruções!

  • Page 2: Table Of Contents

    Customer Explanation ..........2 Things to remember when wired and wireless Setting Address Switches ..........11 remotes are installed at the same time ......2 CZ-RWSC2 CZ-RWSU2 Accessories ..............12 Accessories ..............4 Installing the Receiver........... 12 Installing the Receiver............. 4 Wiring the Receiver............

  • Page 3: Warnings About Installation Of Receivers

    Common to All Models Warnings about Installation of Receivers The wireless remote uses a very weak infrared light for its signal, which can result in the signal not being received because of the following infl uences, so take care in where the unit is installed. •...
  • Page 4 200 m. ※ (Sub) 1st Indoor 2nd Indoor 3rd Indoor 4th Indoor Unit Unit Unit Unit CZ-RWSU2 CZ-RWST2 S003 Bit 3: OFF→ON Screw Cable clamp S003 Bit 3: OFF→ON Receiver PCB PCB cover Adjustable...

  • Page 5: Cz-Rwsu2

    CZ-RWSU2 Accessories Accessories Quantity Accessories Quantity Receiver Dry-cell Batteries Users Manual Truss Self-Tapping Screws 4 × 16 Remote Control Cable clamp Remote Control Holder Installing the Receiver The receiver can only be installed on the corner indicated in Fig. A, so consider how the panel will face when it is installed on the indoor unit.

  • Page 6: Wiring The Receiver

    CZ-RWSU2 Wiring the Receiver Wiring Diagram Indoor Unit Receiver PCB Terminal Strip for White Wiring Remote Black Controls Connections ・ Connect the wires from the receiver to the remote control terminal strip on the indoor unit. (Polarity does not matter)

  • Page 7: Cz-Rwst2

    CZ-RWST2 Accessories Accessories Quantity Accessories Quantity Receiver Dry-cell Batteries Users Manual Remote Control Truss Self-Tapping Screws 4 × 16 Remote Control Holder Cable tie Installing the Receiver Ceiling Suspended Model 1 Open the air inlet grill on the side panel, remove the 1 screw and then move it toward the front (direction of the arrow) and remove it.

  • Page 8: Wiring The Receiver

    CZ-RWST2 Unidirectional cassette model for high ceilings/Unidirectional ceiling cassette model 1 While spreading the tabs of the cover, pull it out from the panel to the front. (Fig. A) 2 Pass the lead wire through the panel and install the receiver in the hole in the panel. (The projecting parts of the receiver hold it in the hole in the panel) 3 Press the lead wire from the receiver in along the rib on the back of the panel.

  • Page 9: Test Operation

    CZ-RWST2 Test Operation Implementing a Test Run 1. Turn the #1 DIP switch [S003] on the receiver’s PCB from OFF to ON and operate the wireless remote control with its Start/Stop button. 2. During a test run, all display lamps on the display will light up. 3.

  • Page 10: Cz-Rwsl2

    CZ-RWSL2 Accessories Accessories Quantity Accessories Quantity Operation Panel Dry-cell Batteries Users Manual Display Truss Self-Tapping Screws 4 × 16 Remote Control Pan Head Self-Tapping Screws 4 × 10 Remote Control Holder Plastic Clamp L150 Installing the Display/Operation Panel Resin Panel Installing the Operation Panel 1 Remove the 2 screws and remove cover A from the back of the panel.

  • Page 11: Wiring

    CZ-RWSL2 Metal Panel Installing the Operation Panel 1 Remove the 2 screws and remove cover A from the back of the panel. (Fig. A) 2 Fasten the operation panel to the location in the diagram below with the 2 enclosed screws (4 × 10). (Fig. B) 3 Pass the wiring for the display (W2, 6P white connector) through the back of the panel.

  • Page 12: Test Operation

    CZ-RWSL2 Test Operation Implementing a Test Run 1. Turn the #1 DIP switch of the operation panel from OFF to ON (Down → Up) and operate the wireless remote control with its Start/Stop button. 2. During a test run, all display lamps on the display will light up. 3.

  • Page 13: Cz-Rwsc2

    CZ-RWSC2 Accessories Accessories Quantity Accessories Quantity Receiver Users Manual (Enclosed 200 mm wiring) Truss Self-Tapping Screws 4 × 16 Remote Control Small screw Remote Control Holder Wood screw Dry-cell Batteries Cable tie Installing the Receiver When using a separately installed receiver as a built-in model, install it to the switch box (fi eld supply) shown in the diagram on the right, which has been built into the wall on site in advance.
  • Page 14 CZ-RWSC2 When using a separately installed receiver as an exposed model, attach it to a wall where the receiver can be affi xed. 1 Put a slotted screwdriver or the like into the groove on the bottom of the receiver unit and twist it to remove the bottom of the case.

  • Page 15: Wiring The Receiver

    CZ-RWSC2 When using a receiver that has been installed separately into the ceiling, use the enclosed fi ttings for installing to a ceiling. Fig. A Fig. B Fig. C Part A Part B 1. Remove the metal plate of the receiver by slipping a slotted screwdriver or the like into the cutout on the bottom. 2.

  • Page 16: Setting Address Switches

    CZ-RWSC2 If it is to be used as an exposed model: Wiring Diagram Terminal strip for wiring White the remote control of the Black indoor unit Receiver Remote Control Cord (Sold Separately) Use remote control cord (sold separately) for wiring a separately installed receiver. 1.

  • Page 17: The Self-Diagnosis Function Display And What Is Detected

    Common to All Models The Self-Diagnosis Function Display and What is Detected Alarm Display in the table below indicates the content of alarms that are displayed when a wired remote control is connected. For information on how to deal with the alarms, refer to the Mounting Instructions for the indoor unit or to Test Run or servicing materials.

  • Page 18: Setting Up Remote Control Functions

    Common to All Models Setting Up Remote Control Functions The functions of the wireless remote can be set on site. (These settings are saved in nonvolatile memory in the remote control, so even when its batteries are changed, the settings do not revert to the defaults.) ...

This manual is also suitable for:

Cz-rwst2Cz-rwsl2Cz-rwsc2

Table of Contents