Optional Controller 1. Remote Controller Servicing Functions Remote Controller Functions • The remote controller includes a number of servicing functions. Use these as needed for test runs and Timer Remote Controller CZ-RTC4 inspections. CZ-RTC4 Fig. 1 List of Servicing Functions...
Therefore use it only when performing the test run.) • The test run can be performed using the HEAT, COOL, or FAN operation modes. CZ-RTC4 The outdoor units will not operate for approximately 3 minutes after the power Fig. 2 is turned ON and after operation is stopped.
Optional Controller 3. Sensor Temperature Display Remote Controller Functions Sensor Temperature Display Function (displayed regardless of whether unit is operating or stopped) The procedure below displays the sensor temperatures from the remote controller, indoor unit, and outdoor unit on the remote controller. 1 Press and hold the buttons simultaneously for 4 seconds or longer.
Page 7
Optional Controller 3. Sensor Temperature Display Remote Controller Functions 2WAY SYSTEM 3. Remote Controller Servicing Functions Remote Controller Functions ex.) 2WAY VRF SYSTEM Indoor unit sensors Outdoor unit sensors Unit No.1 Unit No.2 Unit No.3 Room temp. controlled* Discharge temp. 1 (DISCH1) Remote controller temp.
At this time, the fan at the indoor unit begins operating. *If unit No. “ ” is displayed, the same setting will be made for all indoor units. CZ-RTC4 4 Press the temperature setting buttons to select the item code to change.
Page 9
Optional Controller 4. Simple Settings Function Remote Controller Functions List of Simple Setting Items Setting data Item code Item Description 0000 Not displayed 0001 150 hours 0002 2,500 hours Filter sign ON time (filter life time) 0003 5,000 hours 0004 10,000 hours 0005 Use the filter clogging sensor.
” is displayed, the same setting will be made for all indoor units. 4 Press the temperature setting buttons to select the item code to change. CZ-RTC4 5 Press the timer time buttons to select the desired setting data. Fig. 5 *For item codes and setting data, refer to the following page.
Page 11
2WAY SYSTEM Optional Controller 5. Detailed Settings Function 2. Detailed Settings Function Remote Controller Functions Remote Controller Functions List of Detailed Setting Items Setting data Item code Item Description Description Description 0001 4-Way Cassette (60×60) (U1, Y1, Y2) 0002 2-Way Cassette (L1) 0003 1-Way Cassette (D1) Low Silhouette Ducted (F1, F2)
Page 12
Optional Controller 5. Detailed Settings Function Remote Controller Functions Setting data Item code Item Description 0000 5 minutes Forced thermostat ON time 0001 4 minutes –010 Shifts discharge temperature setting 10°C down –009 Shifts discharge temperature setting 9°C down Cooling discharge –008 Shifts discharge temperature setting 8°C down temperature shift...
Page 13
Optional Controller 5. Detailed Settings Function Remote Controller Functions Setting data Item code Item Description 0000 No forced operation 0001 Forced operation for 1 minute Automatic drain pump operation 0060 Continuous operation 0000 None Ventilation fan operation 0001 Ventilation fan operated by remote controller. Wired remote controller 0000 Not used.
Page 14
Optional Controller 5. Detailed Settings Function Remote Controller Functions Setting data Item code Item Description DC fan tap operating Purpose mode 0000 Standard Standard (setting at shipment) High ceiling use High ceiling setting 1 (with standard panel) 0001 For low Ultra long-life filter, oil guard panel, ammonia deodorizing static-pressure filter filter, optical regenerative deodorizing filter...
Page 15
Optional Controller 5. Detailed Settings Function Remote Controller Functions Selecting the DC fan motor tap (when setting with the remote controller) Stop the system before performing these steps. 1 Press and hold the buttons simultaneously for 4 seconds or longer. 2 If group control is in effect, press the button to set.
(During automatic address setting, “ ” is CZ-RTC4 displayed on the remote controller. This message disappears when automatic address setting is completed.) Repeat the same steps to perform automatic address setting for each successive system.
Page 17
Optional Controller 6. Automatic Address Setting Remote Controller Functions Request concerning recording the indoor/outdoor unit combination Nos. After automatic address setting has been completed, be sure to record them for future reference. List the outdoor main unit system address and the addresses of the indoor units in that system in an easily visible location (next to the nameplate), using a permanent marking pen or similar means that cannot be abraded easily.