Table of Contents
Quick Links
Table of Contents
Related Manuals for Panasonic CZ-RWSU3U
Summary of Contents for Panasonic CZ-RWSU3U
- Page 1 Operating Instructions Wireless Remote Controller CZ-RWSU3U Model No. CZ-RWST2U CZ-RWSD2U CZ-RWSC3 CZ-RWSK1U Be sure to read the “Safety Precautions” before using. Keep them for future reference. Panasonic Corporation 1006 Kadoma, Kadoma City, Osaka, Japan DC0815-0 85464609302010 CV6233317687...
- Page 2 REMOTE CONTROLLER Receiver CZ-RWST2U CZ-RWSU3U CZ-RWSD2U CZ-RWSC3 ADDRESS 1 ADDRESS 2 ADDRESS 3 REM SUB/MAIN 1 2 3 4 Front side Rear side (EN)
- Page 3 Safety Precautions Note: z This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
- Page 4 Safety Precautions WARNING CAUTION This symbol refers to a hazard or unsafe This symbol refers to a hazard or unsafe practice which can result in severe personal practice which can result in personal injury or injury or death. product or property damage. Matters to be observed Prohibited matters WARNING...
-
Page 5: Table Of Contents
Contents 1. Important Safety Instructions ..........5 2. Names and Operations ............6 3. Installing Batteries ..............8 4. Setting the Current Time ............9 5. Operation ................10 6. Timer Operation ..............12 7. Adjusting the Wind Direction ..........14 8. Operating Multiple In/Outdoor Units Simultaneously ..15 9. -
Page 6: Important Safety Instructions
1. Important Safety Instructions Before using the system, be sure to Moving and Repair read these “Important Safety Precautions Instructions”. After reading this manual, save it in a • Do not repair. convenient place. Never repair the system yourself. • Contact your distributor before WARNING moving the system. Contact your distributor or a Installation Precautions professional service provider about... -
Page 7: Names And Operations
2. Names and Operations One remote controller can control a group of REMOTE CONTROLLER up to eight indoor units. (See page 15) 1. Operation Display 11. Filter button Displays the operation status. CZ-RWSC3 (The figure shows all the possible Press to turn off the filter lamp on segments that may appear on the the receiver. - Page 8 2. Names and Operations (Cont.) Receiver 1. Receiver Note Receives the signal sent from the • If HEAT PUMP (2WAY) type is being used, it will beep twice and the remote controller. operating lamp will light up on the 2. Emergency operation button display; if the timer and standby lamps blink alternately, a conflict between the Indicator lamps heating and cooling exists, so the unit...
-
Page 9: Installing Batteries
3. Installing Batteries 1. Remove the cover. 2. Insert two AAA alkaline batteries. Put the batteries in with the polarity [+/–] as shown in the figure. 3. Gently insert one end of an unfolded paper clip (or a similar object that can fit) into the Reset Reset hole hole and press the RESET button inside the hole, then put the cover... -
Page 10: Setting The Current Time
4. Setting the Current Time After changing the batteries and pressing the RESET button, be sure to reset the current time. (When the RESET button is pressed, the current time reverts to [ 1. Press for two seconds or more. Once the clock displays starts blinking, the clock can be set. -
Page 11: Operation
5. Operation , Dry , Cool , Fan Auto , Heat Models that only provide the cooling function cannot operate in the auto or heating mode. Power: Turn on the circuit breaker beforehand, referring to the operating instructions for the unit. - Page 12 5. Operation (Cont.) If the unit is not heating effectively with a Low fan speed , switch the fan speed to High or Medium Depending on the type of indoor unit being used, it may indicate a function that it does not have. (The fan speed is constant.) If you cannot turn the air conditioner off in the normal way Disconnect the power to the indoor unit and contact the distributor where the product was purchased.
-
Page 13: Timer Operation
6. Timer Operation • When setting the timer, make sure the current time on the remote controller is accurate. • The timer’s clock can only be set when the display of the remote controller is ON. • After setting the timer, put the remote controller for in a place where its signal will reach the receiver of the indoor unit. (When the time set for the timer is reached, a signal is sent from the remote controller to start or stop the unit.) Using the Timer , and... - Page 14 6. Timer Operation (Cont.) Combining ON and OFF Timers • The ON and OFF timers can be set respectively. Checking the timer setting • If you press either for the or the , the scheduled time is displayed for four seconds. • When no timer setting has been made, it displays --:--. (Initial setting) Changing a timer setting • Press for the or the , and then when the timer setting is displayed, press...
-
Page 15: Adjusting The Wind Direction
• When the unit stops, the flap (up-down wind direction plate) automatically faces downwards. • When the unit is in heating standby, the flap (up-down wind direction plate) faces upwards. Also, bear in mind that the flap starts swinging after the heating standby mode is released, but the display on the remote controller indicates Auto Flap during standby heating as well. CZ-RWSU3U/CZ-RWSD2U/ In Heat Mode CZ-RWST2U/CZ-RWSC3 Please face the flap Setting the Wind Direction (up-down wind While the unit is operating, every time... -
Page 16: Operating Multiple In/Outdoor Units Simultaneously
7. Adjusting the Wind Direction (Cont.) CZ-RWSC3 The available functions differ depending on the indoor unit being used. The wind direction cannot be set via remote controller for any models other than those noted below. For more information, please refer to the Operating Instructions that came with your indoor unit. -
Page 17: Using The Remote Controller
9. Using the Remote Controller • Point the transmitter of the remote controller at the receiver. When the signal is received properly, it will beep one time. (It only beeps two times when the unit starts operating.) • The signal can be received at a distance of up to about 6 meters. This distance should be used only as a guide. It depends on battery strength. • Make sure nothing is between the remote controller and the receiver that could block the signal. -
Page 18: Addresses
11. Addresses In both multi and single unit installations, when more than one indoor units are installed in the same room with a compatible wireless remote controller, addresses can be set up to avoid crosstalk. By setting the address switches on the receivers and matching them with the number of addresses on the remote controller, up to six indoor units can be controlled separately with the remote controller. (When using units in a flexible combination or operating multiple units simultaneously, they cannot be... - Page 19 11. Addresses (Cont.) Setting Addresses (Setting the address of the indoor unit) 1. Set the address for the remote controller following the procedure under the section “Setting Remote Controller Addresses” (see page 17). 2. Press [Emergency Operation] of the indoor unit for 4 seconds or longer.
-
Page 20: Emergency Operation
• When the remote controller’s batteries have failed. • When the remote controller is broken. • When the remote controller is lost. Figures: CZ-RWSU3U, CZ-RWSD2U, and CZ-RWST2U are of receivers (inside indoor unit). CZ-RWSU3U/CZ-RWSD2U/CZ-RWST2U/CZ-RWSC3 Start: press [Emergency Operation] of the receiver. If the indoor temperature is 75 °F (24 °C) or greater when the unit starts running, it will act as a cooler. -
Page 21: Miscellaneous Settings
13. Miscellaneous Settings A variety of changes can be made to settings, depending on the type of indoor unit being used. Operation mode indicator, time display (24-hour, AM/PM), heating maximun temperature • (These settings are saved in nonvolatile memory in the remote controller, so even when its batteries are changed, the settings do not have to be made again.) • First check the display of the remote controller when the unit is stopped and then make any desired settings. -
Page 22: Before Requesting Service
14. Before Requesting Service Before requesting service, please check the following. Problem Cause Solution The unit doesn’t work The power to the indoor unit is not Make sure the power to the indoor even when unit is ON. pressed on the remote Is the Normal/Stop All switch in the Switch it to the Normal position controller. -
Page 23: Specifications
15. Specifications CZ-RWSU3U/CZ-RWSD2U/CZ-RWST2U/CZ-RWSC3 (H) 7-11/64” × (W) 2-13/32” × (D) 47/64” Dimensions ((H) 182 mm × (W) 61 mm × (D) 18.5 mm) Wireless Remote Controller Power source Two AAA alkaline batteries Clock Accuracy ±30 seconds per month (at 77 °F (25 °C)) CZ-RWSU3U/CZ-RWSD2U/CZ-RWST2U/CZ-RWSC3 (H) 7-7/8”... - Page 24 Panasonic Corporation Website: http://www.panasonic.com Printed in Japan © Panasonic Corporation 2015...