Honeywell SILENT KNIGHT 6700 Manual
  1. Manuals
  2. Brands
  3. Honeywell Manuals
  4. Control Panel
  5. SILENT KNIGHT 6700
  6. Manual

Honeywell SILENT KNIGHT 6700 Manual

Addressable fire alarm control panel
Hide thumbs
Table of Contents

Quick Links

6700
Addressable Fire Alarm Control Panel
Manual
Document LS10148-001SK-E Rev: F
8/29/2022 ECN: 00021453
Table of Contents
loading

Related Manuals for Honeywell SILENT KNIGHT 6700

Summary of Contents for Honeywell SILENT KNIGHT 6700

  • Page 1 6700 Addressable Fire Alarm Control Panel Manual Document LS10148-001SK-E Rev: F 8/29/2022 ECN: 00021453...
  • Page 2 Fire Alarm & Emergency Communication System Limitations While a life safety system may lower insurance rates, it is not a substitute for life and property insurance! An automatic fire alarm system—typically made up of smoke IMPORTANT! Smoke detectors must be installed in the same room detectors, heat detectors, manual pull stations, audible warning as the control panel and in rooms used by the system for the devices, and a fire alarm control panel (FACP) with remote...
  • Page 3 Flexput®, Honeywell®, JumpStart®, Silent Knight®, and SWIFT® are registered trademarks of Honeywell International Inc.Microsoft® and Windows® are registered trademarks of the Microsoft Corporation. Chrome™ and Google™ are trademarks of Google Inc. Firefox® is a registered trademark of The Mozilla Foundation.
  • Page 4 Your suggestion for how to correct/improve documentation Send email messages to: [email protected] Please note this email address is for documentation feedback only. If you have any technical issues, please contact Technical Services. This symbol (shown left) on the product(s) and / or accompanying documents means that used electrical and electronic products should not be mixed with general household waste.

  • Page 5: Table Of Contents

    Table of Contents Section 1: Introduction ..............................9 1.1: Basic System Overview.....................................9 1.1.1: Hardware Features ....................................9 1.1.2: Common Communication / Annunciation Link System Hardware Features ..................9 1.1.3: Software Features ....................................9 1.2: About this Manual......................................10 1.2.1: Terms Used in this Manual...................................10 1.3: Compatible Products......................................10 1.4: Related Documentation ....................................11 Section 2: Agency Listings, Approvals, and Requirements..................
  • Page 6 Table of Contents 4.12.1: FACP Connection....................................43 4.12.2: 5865 Mounting....................................44 4.13: Configuring Modules.....................................44 4.13.1: Assigning Module IDs..................................44 4.13.2: Communication Protocol ..................................45 4.13.3: End-of-Line Resistor ..................................45 4.14: Telephone Connection ....................................46 4.15: Notification Appliance/Auxiliary Power Circuits ............................46 4.15.1: Conventional Notification Appliance ..............................46 4.16: Class A Notification Wiring...................................47 4.16.1: Auxiliary Power Installation................................47 4.17: Onboard Relays (Conventional) ..................................48 4.17.1: Common Trouble Relay ..................................48...
  • Page 7 Table of Contents Section 8: Programming ..............................74 8.1: UL 864 Programming Requirements ................................74 8.2: Modules ...........................................74 8.2.1: Edit Modules......................................74 8.2.2: Adding Modules ....................................75 8.2.3: Deleting Modules....................................75 8.2.4: View Module List ....................................75 8.3: Zone ..........................................75 8.3.1: Edit Zone ......................................75 8.3.2: View Zone Points ....................................77 8.4: Group ..........................................78 8.4.1: Edit Group ......................................78 8.4.2: View Group Points ....................................78...
  • Page 8 Table of Contents 9.8.3: Erasing an F-Key Macro..................................101 9.8.4: Using a Recorded F-Key Macro .................................102 9.8.5: F-Key Status Event .....................................102 9.8.6: F-Key Map Inhibit ....................................102 Section 10: Reporting ..............................103 10.1: Receivers Compatible with the Control Panel.............................103 10.2: SIA / 6700 Panels PI Modifier Reporting..............................112 10.3: SIA–...

  • Page 9: Section 1: Introduction

    Section 1: Introduction The 6700Fire Alarm Control / Communicator is an Addressable Fire Alarm Control System that meets the requirements of UL 864 10th Edi- tion Standard. 1.1 Basic System Overview 1.1.1 Hardware Features • The 6700 has one built in signaling line circuit (SLC) that supports 50 SK detectors and 50 SK modules or 50 SD devices. •...

  • Page 10: About This Manual

    Introduction About this Manual 1.2 About this Manual This manual is intended to be a complete reference for all installation and operation tasks for the 6700. 1.2.1 Terms Used in this Manual The following terminology is used with the 6700 system: Term Description Signaling Line Circuit...

  • Page 11: Related Documentation

    Related Documentation Introduction Type of Device Model Description Wireless WSK-WGI Wireless Gateway WSK-PHOTO Wireless Photoelectric Smoke Detector with 4”base WSK-PHOTO-T Wireless Photoelectric/Heat Detector with 4”base WSK-HEAT-ROR Wireless ROR Heat Detector with 4”base WSK-HEAT Wireless Fixed Heat (135°F) Detector with 4”base WSK-MONITOR Wireless Addressable Monitor Module WSK-RELAY...

  • Page 12: Section 2: Agency Listings, Approvals, And Requirements

    NFPA 72. 2.1 Federal Communications Commission (FCC) The following information must be provided to the Telephone Company before the 6700 can be connected to the phone lines: Manufacturer: Honeywell Silent Knight Model Number: 6700 FCC registration number:...

  • Page 13: Underwriters Laboratories (Ul)

    Underwriters Laboratories (UL) Agency Listings, Approvals, and Requirements CAUTION: INSTALLATION AND TEST TO ENSURE PROPER OPERATION, THIS EQUIPMENT MUST BE INSTALLED ACCORDING TO THE ENCLOSED INSTALLATION INSTRUCTIONS. TO VERIFY THAT THE EQUIPMENT IS OPERATING PROPERLY AND CAN SUCCESSFULLY REPORT AN ALARM, THIS EQUIPMENT MUST BE TESTED IMMEDIATELY AFTER INSTALLATION, AND PERIODICALLY THEREAFTER, ACCORDING TO THE ENCLOSED TEST INSTRUCTIONS.

  • Page 14: 6: Requirements For The Installation Of Carbon Monoxide (Co) Detection And Warning Equipment, Nfpa 72

    Agency Listings, Approvals, and Requirements Underwriters Laboratories (UL) 2.2.6 Requirements for the Installation of Carbon Monoxide (CO) Detection and Warning Equipment, NFPA 72 When using carbon monoxide detection the system must be monitored by a Supervising Station with emergency response, both aspects meet- ing the Standard for the Installation of Carbon Monoxide (CO) Detection and Warning Equipment, NFPA 72.

  • Page 15: Section 3: Prerequisites For Installation

    System. Contact Technical Support with any ques- tions about software and the appropriate version for a specific application. The HFSS Honeywell Fire Software Suite is available at www.silentknight.com.

  • Page 16: Calculating Current Draw And Standby Battery

    Prerequisites for Installation Calculating Current Draw and Standby Battery Label Rating Terminal No. Description Group Individual Voltage Current Terminal Block 2 SBUS – SBUS Power 27.4 VDC 0.5 A SBUS Communication 5 VDC 100 mA NAC1 – Notification Appliance Circuit/Auxiliary power 27.4 VDC 1 Amp NAC or Aux power NAC2...
  • Page 17 Calculating Current Draw and Standby Battery Prerequisites for Installation Standby Device # of Devices Current per Device Alarm Current Current SK-PHOTO-W SK-PHOTO-T-W SK-PHOTO-R-W SK-HEAT-W Standby: 0.2 mA Alarm: 4.5 mA SK-HEAT-HT-W SK-HEAT-ROR-W SK-PHOTO-CO-W SK-CO-W SK-BEAM (without integral test) Standby/Alarm: 2 mA Aux.
  • Page 18 Prerequisites for Installation Calculating Current Draw and Standby Battery Standby Device # of Devices Current per Device Alarm Current Current SK-ZONE-6 Aux Pwr Standby 50 mA Alarm: 70 mA Standby 2.3 mA Alarm: 40 mA SLC Accessories B200SR/-W/-IV Sounder Base Aux Pwr Standby: 0.5 mA...
  • Page 19 Calculating Current Draw and Standby Battery Prerequisites for Installation Standby Device # of Devices Current per Device Alarm Current Current SK-FML Fiber Optic Multi Mode Standby/Alarm: 53 mA SK-FSL Fiber Optic Single Mode Standby/Alarm: 79 mA Wireless Modules WSK-WGI Wireless Gateway Max current using ext supply 40 mA Max current SLC Power...

  • Page 20: 3: Current Draw Worksheet For Sd Slc Devices

    Prerequisites for Installation Calculating Current Draw and Standby Battery 3.5.3 Current Draw Worksheet for SD SLC Devices Use Table 3.3 Table 3.3 to determine current requirements during the alarm/battery standby operation when the SD SLC devices are installed. You can install up to 75 SD devices per panel. Standby Device # of Devices...
  • Page 21 Calculating Current Draw and Standby Battery Prerequisites for Installation Standby Device # of Devices Current per Device Alarm Current Current 5865-3 LED Annunciator Module Standby: 35 mA Alarm: 145 mA 5880 LED I/O Module Standby: 35 mA Alarm: 200 mA 5883 Relay Interface Standby: 0 mA...
  • Page 22 Prerequisites for Installation Calculating Current Draw and Standby Battery Maximum Battery Standby Load Table 3.4 shows the maximum battery standby load for the 6700 based on 24 and 60 hours of standby. The standby load calculations of line G in the Current Draw Calculation Worksheets (Table 3.2 and Table 3.3) must be less than the number shown in Table 3.4 for the battery size used and standby hours required.

  • Page 23: Section 4: Control Panel Installation

    Section 4: Control Panel Installation CAUTION: DISCONNECT POWER TO AVOID THE RISK OF ELECTRICAL SHOCK AND DAMAGE TO THE UNIT, POWER SHOULD BE OFF AT THE CONTROL PANEL WHILE INSTALLING OR SERVICING. 4.1 Mounting the Control Panel Cabinet Read the Environmental Specifications in Section 3.2 before mounting the 6700 panel. The 6700 cabinet base dimensions are: 12.531”...
  • Page 24 Control Panel Installation Mounting the Control Panel Cabinet Close the dead front panel. The bottom two screws on the annunciator will protrude through the dead front panel. Reinstall the top two annunciator screws removed in step 1. Insert the two screws with the star washers into the bottom of the cabinet to secure the dead front to the cabinet. remove top two annunciator screws from board and secure through dead front panel bottom two screws protrude...

  • Page 25: Board Assembly Diagram

    Board Assembly Diagram Control Panel Installation 4.2 Board Assembly Diagram The drawing below shows the location of components for FACP wiring. onboard annunciator DIP switch Power Input: 120VAC, 60Hz, 1.5A Ethernet Cellular connection battery connection phone line Form C SBUS NACs/ connection Trouble Relays...

  • Page 26: Ac Power Connection

    Control Panel Installation AC Power Connection AC input NAC circuits Phone lines Note: 0.25” spacing must be maintained between each of these circuit types; as well as between power-limited and non-power-limited circuits. Battery connection SBUS Relays Battery Battery Figure 4.4 Wire Routing Example 4.4 AC Power Connection At installation, connect the AC terminals to the power source as shown in Figure 4.5.

  • Page 27: Battery Power

    Battery Power Control Panel Installation 4.5 Battery Power The batteries must be sealed lead acid type. Before connecting the batteries to the FACP, make certain that the interconnect cable between the batteries is not connected. Do not connect the battery jumper cable until the system is completely installed. Observe polarity when connect- ing the batteries.
  • Page 28 Control Panel Installation Battery Power cabinet mounting holes Figure 4.7 RBB Cabinet Mounting Holes Connect the main control panel battery cables to the battery cable extenders as shown below. Figure 4.8 Splicing Control Panel Battery Cable to RBB Battery Cable Extenders Run extended battery cable from control panel cabinet through conduit to RBB cabinet as shown below.

  • Page 29: Wiring Specifications

    Wiring Specifications Control Panel Installation Slide the cover into place and tighten the cover mounting screws. cabinet mounting holes Figure 4.10 Cover Plate Mounting Keyholes and Cover Mounting Screws Alignment 4.6 Wiring Specifications 4.6.1 Length Limitations This section contains information on calculating SBUS wire distances and the types of wiring configurations (Class A and B). 4.6.2 Calculating Wiring Distance for SBUS Modules The following instructions will guide you in determining the type of wire and the maximum wiring distance that can be used with SBUS accessory modules.
  • Page 30 Control Panel Installation Wiring Specifications These cases are marked in the chart with an asterisk (*). Maximum length can never be more than 6,000 feet, regardless of gauge used. (The formula used to generate this chart is shown in the chart below). Wiring Distance: SBUS Modules to Panel Total Worst Case 22 Gauge...

  • Page 31: 3: Wiring Configurations

    6855 Remote Annunciator Installation Control Panel Installation 4.6.3 Wiring Configurations Figure 4.11 illustrates the Class B configuration. FACP supervised, power-limited, Class B NAC 1 TROUBLE SLC IN SLC OUT SLC PROG SBUS NAC 2 SBUS device Figure 4.11 SBUS Class B Wiring How to Power SBUS Devices From an Auxiliary Power Supply Figure 4.12 illustrates how to power SBUS devices from an auxiliary power supply such as the 5495 or 5499, when the maximum number of SBUS devices exceeds the FACP SBUS power requirements.

  • Page 32: 1: Mounting The 6855

    Control Panel Installation 6855 Remote Annunciator Installation Model 6855 Figure 4.13 6855 Remote Annunciator 6855 installation involves the following steps: Ensure power is off at the panel. Mount the 6855 in the desired location (see Section 4.7.1). Connect the 6855 to the panel (see Section 4.6.3). Use the DIP switches on the back of the 6855 to assign an ID#.
  • Page 33 6855 Remote Annunciator Installation Control Panel Installation Figure 4.15 Attaching Annunciator/Door Assembly to Backbox Surface Mounting The optional Model RA-100TR Trim Ring Kit is available for use when surface mounting. Remove the desired knockout. Mark and pre-drill hole in the wall for the center top keyhole mounting bolt. Refer to Figure 4.14 for mounting hole locations. Install center top fastener in the wall with the screw head protruding.

  • Page 34: 2: 6855 Connection To The Panel

    Control Panel Installation 5860 Remote Annunciator Installation 4.7.2 6855 Connection to the Panel Connect the 6855 to the panel as shown below. supervised, power-limited, Class B Figure 4.17 6855 Connection to the Panel 4.8 5860 Remote Annunciator Installation The 5860 is an optional remote annunciator. Up to 8 annunciators can be added to the 6700 system. FIRE ALARM ANNUNCIATOR Figure 4.18 5860 Remote Annunciator 5860 installation involves the following steps:...
  • Page 35 5860 Remote Annunciator Installation Control Panel Installation FIRE ALARM ANNUNCIATOR Figure 4.19 Annunciator Parts The 5860 comes from the factory fully assembled. You must disassemble it for mounting. To disassemble the annunciator, use a 5/64 hex wrench to remove the set screws, located on the bottom of the annunciator bezel. (See Figure 4.20 for location of the set screws.) screws for placement of mounting wires surface mounting holes...
  • Page 36 Control Panel Installation 5860 Remote Annunciator Installation Attach second set of wires to top of backbox. Secure wires behind screw. Insert wires at an angle into the first holes past sheetrock. Figure 4.21 Flush Mounting the Backbox Surface Mounting The 5860 can be mounted directly to a surface or can be attached to a single, double, or four-square electrical box. Trim Ring Kit 5860TR/G is available for use when surface mounting.

  • Page 37: 6860 Remote Annunciator Installation

    6860 Remote Annunciator Installation Control Panel Installation 4.9 6860 Remote Annunciator Installation The optional 6860 Remote Annunciator can be surface or flush mounted. BACK BACK BACK NEXT NEXT NEXT Model 6860 Figure 4.23 6860 Remote Annunciator 6860 installation involves the following steps: Ensure power is off at the panel.
  • Page 38 Control Panel Installation 6860 Remote Annunciator Installation Attach the annunciator and door assembly to back box as shown below using the supplied screws. Figure 4.25 Attaching Annunciator / Door Assembly to Backbox Surface Mounting The RA-100TR Red Trim Ring kit is available for use when surface mounting the 6860. Remove the desired knockout.

  • Page 39: 2: 6860 Connection To The Panel

    5824 Serial/Parallel Printer Interface Module Installation Control Panel Installation 4.9.2 6860 Connection to the Panel Connect the 6860 to the panel as shown below. supervised, power-limited, Class B Figure 4.27 6860 Connection to the Panel 4.10 5824 Serial/Parallel Printer Interface Module Installation The 5824 Serial/Parallel Printer Interface Module allows you to connect a printer to the panel.

  • Page 40: 5880 Led Driver Module

    Control Panel Installation 5880 LED Driver Module Press ENTER to bypass the next two screens. A screen similar to the one shown below will display. Select Yes if printer should be supervised for Monitor Printer=Yes Out-of-Paper and Offline conditions. Output Port=Parallel Select type of printer, Parallel or Serial.

  • Page 41: 2: Facp Connection

    5880 LED Driver Module Control Panel Installation 4.11.2 FACP Connection The 5880 connects to the panel via the SBUS. Make connections as shown below. After the 5880 is connected to the panel, it must be added to the system. Programming is described in Section 8. 5880 SLC OUT SLC PROG NAC 1...

  • Page 42: 4: Dry Contact Wiring

    Control Panel Installation 5880 LED Driver Module Pin # LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8 Cathode LED9 LEDs LED10 LED Power Anode no connection Pin # LED11 LED12 LED13 LED14 LED15 LED16 LED17 LED18 Cathode LED19 P3 and P4 are wired LEDs LED20 the same as P2.

  • Page 43: 5865-3/5865-4 Led Annunciator Installation

    5865-3/5865-4 LED Annunciator Installation Control Panel Installation 4.12 5865-3/5865-4 LED Annunciator Installation The 5865-3 and 5865-4 are LED annunciators. The 5865-4 has 30 mappable LEDs, remote silence and reset key switches, and a general sys- tem trouble LED. The 5865-3 has 30 mappable LEDs only. These are arranged as 15 pairs of red (typically used for alarm) and yellow (typ- ically used for trouble) LEDs.

  • Page 44: 2: 5865 Mounting

    Control Panel Installation Configuring Modules 4.12.2 5865 Mounting Mount the 5865-4 to a standard 4-gang electrical box. Mount the 5865-3 to a standard 3-gang electrical box. In Figure 4.36, the 5865-4 is attached to a 4-gang box as an example. Attach the 5865 to a standard 3- or 4-gang electrical box.

  • Page 45: 2: Communication Protocol

    Configuring Modules Control Panel Installation address address address address Figure 4.38 Possible SBUS Module Addresses Refer to Section 8.2 to edit, add, delete, and view module list. 4.13.2 Communication Protocol DIP switch 7 on the 6860, 6855, and 5860 is used to determine the communication protocol of the device. Set DIP switch 7 to ON for SBUS protocol.

  • Page 46: Telephone Connection

    4.14 Telephone Connection Connect the telephone lines as shown in Figure 4.39. Model 7860 phone cord is available from Honeywell for this purpose. A number of programmable options are available for customizing the telephone lines. These options are described in Section 8.6.

  • Page 47: Class A Notification Wiring

    Class A Notification Wiring Control Panel Installation 4.16 Class A Notification Wiring You must use an appliance from the list of compatible appliances listed in the Device Compatibility Document, P/N: LS10167-004SK-E. To install a Class A notification appliance circuit: Wire the Class A notification appliances as shown in Figure 4.41. CAUTION: SYSTEM SUPERVISION FOR PROPER SYSTEM SUPERVISION DO NOT USE LOOPED WIRE UNDER TERMINALS MARKED –...

  • Page 48: Onboard Relays (Conventional)

    Control Panel Installation Onboard Relays (Conventional) Constant Power Use constant power for applications that require a constant auxiliary power source. Power is always present at Constant circuits. Resettable Power Resettable power is typically used to power beam detectors, flame detectors and conventional 4-wire smoke detectors. For circuits selected as Resettable, 27.4 volt power is always present at the terminals unless a system reset occurs.

  • Page 49: 2: City Box Connection Using The 5220 Module

    Remote Station Applications Control Panel Installation This is intended for connection to a polarity reversal circuit of a remote station SLC IN SLC OUT SLC PROG NAC 1 RELAY 2 RELAY 1 TROUBLE SBUS NAC 2 receiving unit having compatible ratings. All circuits power-limited.

  • Page 50: 3: Nfpa 72 Polarity Reversal

    Control Panel Installation Remote Station Applications 4.18.3 NFPA 72 Polarity Reversal Using the 5220 Module When the 5220 is wired and programmed for polarity reversal, it reports alarm and trouble events to a remote site. Alarms will override trou- ble conditions and it will not be possible to reset the remote indicator until the condition is cleared and the control panel is reset. If an alarm condition occurs, the alarm relay will close, overriding the trouble condition.

  • Page 51: 5: Transmitter Activated By Dry Contacts

    Remote Station Applications Control Panel Installation RELAY 2 RELAY 1 TROUBLE SLC IN SLC OUT SLC PROG SBUS NAC 1 NAC 2 Intended for connection to a polarity 1kΩ reversal circuit of a remote station resistor receiving unit having compatible rating. MR-201 to remote receiving...

  • Page 52: Section 5: Common Communication Link

    Section 5: Common Communication Link 5.1 Hardware Features 5.1.1 Panels The 6700 panel can be connected to other 6700 and addressable panels to create a link where one panel is designated as the communicator for all the panels in the link. Up to 17 panels can be connected in the Common Communication Link. This does not create a peer-to-peer net- work and will not operate as one.SK Wiring Options to Connect Panels The 6700 and other applicable addressable panels can be linked together for common communications to the central station.

  • Page 53: 1: Fiber Loop Modules

    SK-NIC Installation Common Communication Link 5.3.1 Fiber Loop Modules Two types of fiber-optic modules are available to use to transmit and receive communication with the SK-NIC. LED1 LED2 SK-FSL Single-Mode Fiber Module SK-FML Multi-Mode Fiber Module Figure 5.3 Types of Fiber Loop Modules The SK-FML (Fiber-Optic Multi-Mode) and SK-FSL (Fiber-Optic Single-Mode) are plug-in fiber loop modules.

  • Page 54: 1: Wiring

    Common Communication Link SK-NIC Installation Use the 6-pin cable included with SK-NIC to connect the 6700 to the SK-NIC. The 6-pin cable must be run in conduit between cabinets. Refer to Figure 5.1. LED1 LED2 Figure 5.5 Panel to SK-NIC Connection Each SK-NIC has the ability to monitor for earth ground faults on the twisted-pairs connected to Port 1 of its terminal block TB2.
  • Page 55 SK-NIC Installation Common Communication Link Fiber-Optic Multi-Mode Wiring between Multiple Panels Fiber-optic cable between multiple panels is shown in Figure 5.7 and Figure 5.8. Class X is shown with a dotted line.. port 2 last control panel/SK-NIC Class X wiring port 1 port 2 next control panel/SK-NIC...

  • Page 56: Setting The Id For Each Panel

    Common Communication Link Setting the ID for Each Panel Fiber-Optic and Twisted Pair Wiring between Multiple Panels A mixture of fiber-optic cable and twisted-pair wiring between multiple panels is shown in Figure 5.9. Class X cabling is shown with a dot- ted line.

  • Page 57: Section 6: Network Management

    This section of the manual describes how to program the network options using the built-in annunciator. All options described in this section can be programmed using the HFSS Honeywell Fire Software Suite. HFSS must be used to edit site assignments.

  • Page 58: 4: Computer Access

    Network Management Network Programming Edit the Network Panel ID Login to the panel. The panel will automatically access the Main Menu. Select 6 to access Network programming. Press 3 to enter the Edit Panel ID Menu. If the Network Panel ID is changed and valid, the system will ask you to confirm the change. If it is not correct, you can change the DIP switches at this time.

  • Page 59: Sync Network Options

    Sync Network Options Network Management • Panel ID* NOTE: *Only the SIA sends the Panel ID when reporting. Receiver Configuration The 6700 Communication Link can report events to as many as 68 receivers. See Appendix B for a list of the panel/receiver relationship numbers.

  • Page 60: Network Management Quick Reference

    Network Management Network Management Quick Reference Select from which panel to source the options. Select Source Select Source Select Source 01= Panel 1 01= 07/28/21 12:20 OF 01=/28/21 12:20 OF8B 02= Panel 2 02 Panel 2 02 Panel 2 03= Panel 3 03 Panel 3 03 Panel 3 Select the line number.

  • Page 61: Section 7: Programming Overview

    Section 7: Programming Overview This section of the manual is intended to give you an overview of the programming process. Please read this section of the manual carefully, especially if you are programming the control panel for the first time. The JumpStart auto-programming feature automates many programming tasks and selects the default options for the system.

  • Page 62: Mapping Overview

    & special optional system events Figure 7.1 Mapping Overview NOTE: Mapping cannot be programmed through the annunciators. It can only be programmed through the HFSS Honeywell Fire Software Suite. 6700 Manual — P/N LS10148-001SK-E:F 8/29/2022...

  • Page 63: 1: Input Point Mapping

    Mapping Overview Programming Overview 7.2.1 Input Point Mapping Input points are assigned to input zones. Any input point can be assigned to any input zone. Input points can be assigned to one zone only. An input point can be designated as “unused,” which means it has not been assigned to a zone. zone 1 point 1 point 2...
  • Page 64 Programming Overview Mapping Overview System Zone Panel Site Emergency Trouble SBUS Expander Trouble General Trouble Status Point Active SBUS Class A Trouble Site Silenced SLC Loop Trouble AC Loss Trouble F1 Key Active Advisory Battery Trouble F2 Key Active Ground Fault Trouble F3 Key Active Phone Line Trouble F4 Key Active...

  • Page 65: 4: Mapping Led Points

    7.3 Programming Using the HFSS Software Suite You can use the HFSS Honeywell Fire Software Suite to program the control panel on-site (the personnel will need to be on-site during the upload or download process). HFSS is a software package that lets you easily program the control panel using a Windows-based computer.

  • Page 66: 2: Moving Through The Menus

    Programming Overview Programming Menu Quick Reference 7.4.2 Moving through the Menus The first line of the display identifies the menu. The option available for editing displays next to the equal sign. Press the ENTER/ACK key to select the desired option. Arrows on the LCD indicate there are more options available. Access these screens by pressing the down arrow key.
  • Page 67 Programming Menu Quick Reference Programming Overview Menu Options/Defaults Reference Edit Zone Name Section 8.3.1 *1-Count 2-Count Alarm Ver. Verification Type SNGL ILOCK Zone Properties DBL ILOCK 135° to 150°F Heat Temp Set 135° to 190°F Edit Zone Select Zone Zone Single/Multi-station 00-23 Cadence...
  • Page 68 Programming Overview Programming Menu Quick Reference Menu Options/Defaults Reference STATUS POINT CO DETECTOR SWITCH LATCH 1, 2, 3 SWITCH SUPERVISORY DETECTOR NON-LATCH SWITCH OUTPUT PT Select Group AUX CONST 1, 2, 3 NOTIF 1, 2 AUX RESET Select Module AUX DOOR Section 8.5.1 OUTPUT PT Select Group...
  • Page 69 Programming Menu Quick Reference Programming Overview Menu Options/Defaults Reference No Accessory base SDR BAS Single station or Multi station RLY BAS Silence or Non- Silence Latch or non- ACCLIMATE latch, Single I-SdrBa station or Multi (Intelligent station, Silence Sounder Base) or Non-Silence, volume high (default) or low...
  • Page 70 Programming Overview Programming Menu Quick Reference Menu Options/Defaults Reference No Accessory base SDR BAS Single station or Multi station RLY BAS Silence or Non- Silence CO ALARM/ Latch or non- FIRE ALARM latch, Single I-SdrBa station or Multi (Intelligent station, Silence Sounder Base) or Non-Silence, volume high...
  • Page 71 Programming Menu Quick Reference Programming Overview Menu Options/Defaults Reference MANUAL PULL WATERFLOW FIRE SUPER- VISORY FIRE TAMPER FIRE DRILL SILENCE Latch and Non-Latch feature only RESET appear for WATERFLOW,FIRE B SWITCH P.A.S. ACK SUPERVISORY, FIRE TAMPER, ZONE AUX1, ZONE AUX2, ZONE AUX 1 SYSTEM AUX1, SYSTEM AUX2 ZONE AUX2...
  • Page 72 Programming Overview Programming Menu Quick Reference Menu Options/Defaults Reference 75 sec, 90 Sec, 3 Ethernet Supervise min, 5 min, 1 hr, 24 *5 Minutes hrs, 30 days, None 24Hrs, 30 days, Cellular Supervise *24 Hours AlarmNet Timers none 10 min, 15 min, 30 Minutes, 1 hr, 2 hrs, Old Alarm Time *30 Minutes...
  • Page 73 Notes 6700 Manual — P/N LS10148-001SK-E:F 8/29/2022...

  • Page 74: Section 8: Programming

    This section of the manual describes how to manually program the control panel from the built-in annunciator. Each subsection describes these menu options. All options described in this section can be performed using the HFSS Honeywell Fire Software Suite. NOTE: JumpStart auto-programming should be run Before any customized programming is performed. Thoroughly test the system after running JumpStart because it automatically programs the system, searching for and configuring all SLC and SBUS devices it finds.

  • Page 75: 2: Adding Modules

    Zone Programming 5880-LED I/O Default name for 5880 module Module ID: 03 (no customization) 5880 03_________ 5880-LED I/O Use arrow keys to select characters. Letters begin displaying with “A”. Press AB_____________ the ENTER key to select the desired character.
  • Page 76 Alarm Delay Characteristics The programmed zone type is provided for user reference only. To modify the zone type, use the HFSS Honeywell Fire Software Suite. Table 8.2 lists the delay choices and a description of each type. Then, press ENTER.

  • Page 77: 2: View Zone Points

    Zone Programming Type of Delay Description Alternate P.A.S. - An improved version of PAS is available with software version 6.04 or higher, for use with the 6860 and 6855 only. Positive Alarm Existing systems with PAS enabled will still function normally. Sequence The PAS option will program an automatic, addressable detector to delay panel activation (including alarm relay and communicator) for a period of 15 seconds plus a delay time of up to three minutes.

  • Page 78: Group

    Programming Group Enter the number of the zone you want to view, then press ENTER. GROUP: G01 zone number POINT: 01:001 NUMBER: 1 of 12 Figure 8.3 View Zone Points Screen 8.4 Group An output group is made up of output points that have been programmed to respond in the same way. output groups simplify programming, because you do not have to program each individual point.

  • Page 79: Point

    Point Programming Press 3 to enter the Group Menu. Press 3 to edit the OPG Template. Enter the Template number, then press ENTER. On the Template name, press ENTER to edit the name. You can enter a description to assign and display a descriptive name for a group. NOTE: See Appendix A for information to edit names.
  • Page 80 Programming Point Type Latching Function Comments Selection Option SK/ SUP SUP PHOTO DUCT Latching Supervisory switches can be latching or non-latching. DETECTOR Non Latching SUP SMOKE PHOTO SUP SMOKE ION SUP HEAT SUP ACCLIMATE SUP HEAT HT SUP SMOKE PHOTO/HEAT SUP SMOKE BEAM CO SMOKE ALRM CO/ALRM...

  • Page 81: 2: Point Programming For The Internal Or External Power Module

    Point Programming Type Latching Function Comments Selection Option ZN_AUX1 Latching Use these switch types if you want to monitor special zone-level conditions. Non Latching ZN_AUX2 Latching Non Latching SYS_AUX1 Latching Use these switch types if you want to monitor special system-wide conditions. Non Latching SYS_AUX2 Latching...

  • Page 82: 3: Point Programming For 5880 And 5865 Modules

    Programming Point Function Selections Choices Type Selections Comments for each Type Enter Point or Circuit Select Type UNUSED NOTIF OUT CTRL CKT AUX PWR CONSTANT Constant auxiliary power. RESETTABLE Resettable auxiliary power. DOOR Door holder auxiliary power. AUX SYNC Sounder Sync auxiliary power for System Sensor B SWITCH* MAN PULL Refer to comments column of Table 8.3 for description of these options...

  • Page 83: 4: Point Programming For The 5496

    System Options Programming Enter the Point Number, then press ENTER. M01 P001 NOTIF Select NOTIF or UNUSED. Select the circuit to program. Select an output group for this notification point. MODULE_1 CKT_1 Select a name for the point. Figure 8.6 Programming Output Points Screen for 5880 and 5865 Modules Press the up or down arrows to select the type (Notification or unused).
  • Page 84 Number of Answer Rings This option is used in conjunction with the HFSS Honeywell Fire Software Suite. Use the option to determine the number of rings before the panel answers a call from the computer. The range is 00-15 rings. This option is factory-programmed as 06 rings, which should be compati- ble for most installations, where the answering machine bypass feature is used.
  • Page 85 Answering Machine Bypass This option is used in conjunction with the HFSS Honeywell Fire Software Suite. This feature ensures that an answering machine will not interfere with communication between the panel and the computer. If an answering machine is used at the panel site, enable this feature; if an answering machine is not used, disable the feature.

  • Page 86: 2: Time Options

    Programming System Options Select 5 to access System Options. From the next menu, select 1 to access Communication Options. Select 5 to access Phone Line Gains. The available options are listed as follows: • Dialing: Low, High (default), Normal • Reporting: Low (default), High, Normal Dialing: High Reporting: Low ...

  • Page 87: 3: Miscellaneous Options

    System Options Programming To program a low AC report delay, follow these steps:. Water Flow Delay:01s Alarm Verify:060s low AC report delay AC Report Delay:03h in hours (00-30) More Figure 8.13 Low AC Report Delay Programming Screen Enter the number of hours before a low AC report will be sent to the central station, then press ENTER. AC Line Frequency The panel’s AC line frequency is selectable for 50 or 60 Hz or Internal.

  • Page 88: 5: Edit Banner

    Programming JumpStart Auto-Programming Daylight Saving Time Start and End This option allows you to adjust the week and month Daylight Saving Time (DST) starts and ends. For this feature to work, you must enable (set to Yes) the Automatic Daylight Savings Adjustment option under Daylight Savings Options. The default values for the DST Start and End are: DST Start: The second Sunday in March DST End: The first Sunday in November...

  • Page 89: Restore Defaults

    Restore Defaults Programming 8.8 Restore Defaults This option allows you to restore the panel to its factory default settings. All programming will be lost. Login to the panel. Select 7 to access Panel Programming. Select 7 for Restore Defaults. From the Warning screen, press the up or down arrow keys to select YES. Then, press ENTER. 6700 Manual —...

  • Page 90: Section 9: System Operation

    Section 9: System Operation The operation of the control panel is simple. Menus guide you step-by-step through operations. This section of the manual is an overview of the Operation Menus. Please read this entire section carefully before operating the panel. After logging in to the panel, press ENTER to view the main menu.
  • Page 91 Menu System System Operation Admin Profiles After initial power-up, the 6700 requires a password change and user account setup before programming. Only Admin1 will be active. Using the login for Admin1, the default password (0000000) must be changed to a new, unique password. This new password must be 7-digits and cannot be sequential or easily guessed.

  • Page 92: 2: Main Menu Overview

    System Operation Basic Operation Invalid Password/Panel Timeout If a password is entered incorrectly or is not a valid password, the panel will display an error message. You must hit ENTER or the left arrow key and re-enter the password correctly. After ten invalid attempts, the panel will panel will lock for 30 seconds and then you can try again. However, if the password has been forgotten, record the 20-character code displayed on the panel and contact Technical Services.

  • Page 93: 3: View Event History

    Basic Operation System Operation Inhibit Output Group Inhibiting an output group prevents the group from being used by system mapping. While inhibited, no event in the system can activate the output group. Press 8 to Inhibit Output Group (OPG). Use the up or down arrow key to select the desired group. Press the right arrow key to inhibit the group.

  • Page 94: 7: Conduct A Communicator Test

    System Operation Basic Operation During a Walk Test, the panel’s normal fire alarm function is completely disabled, placing the panel in a local trouble condition. All zones respond as 1-count zones (responds when a single detector is in alarm) during a Walk Test. Each alarm initiated during the Walk Test will be reported and stored in the event history buffer.

  • Page 95: 12: View Status Of A Point

    Basic Operation System Operation Example of detector not in compliance Example of detector in compliance blanks indicate percent obscurity SMOKE PHOTO 2.5% SMOKE PHOTO ---% detector not in per foot compliance detector ID MODULE_33 POINT_4 MODULE_33 POINT_4 [Z001] [M33:004] A058 [Z001] [M33:004] A058 current value detector state...

  • Page 96: Operation Mode Behavior

    System Operation Operation Mode Behavior Ethernet Info Screen From the System Information menu, press 5 to access the Ethernet Information. MAC:00D0.2D73.489C Sub: 000.000.000.000 IP:000.000.000.000 GW: 000.000.000.000 DHCP: Y Next Back MAC CRC:0000 AlarmNet Info Screen From the System Information menu, press 6 to access AlarmNet Information. The following information displays. •...
  • Page 97 Panel Operating Modes System Operation Table 9.4 describes the behavior of the panel in each of these modes. Operating Occurs When System Behavior In This Mode You Can Mode Normal No alarm, supervisories SYSTEM POWER LED is on. The All Systems Normal Enter the appropriate code or rotate the key to or trouble condition exists display indicates that the system is in normal mode.
  • Page 98 System Operation Panel Operating Modes Operating Occurs When System Behavior In This Mode You Can Mode Supervisory The communicator seizes control of the phone line and Press the down arrow key to view the supervisory calls the central station. condition. A screen similar to this one displays. The onboard annunciator sounds a loud, pulsing beep in device SUPERVSY: MAN_PULL...

  • Page 99: 1: Multi-Site Annunciator And Multi-Site User Access

    Releasing Operations System Operation Operating Occurs When System Behavior In This Mode You Can Mode Reset The RESET button is All LEDs are on briefly then the LCD displays “ALARM Menus are not available during the reset process. pressed followed by a RESET IN PROGRESS”.

  • Page 100: 1: Single Interlock Zone Releasing

    System Operation Releasing Operations + – Either NAC circuit can be used. UL-listed solenoid supervisory module- must be located at the solenoid. black releasing solenoid Use 1 solenoid per circuit. Figure 9.6 Wiring Configuration for Solenoid NOTE: For releasing operations, a manual releasing disconnect switch is required per UL 864. Refer to the MRD-1 Series Document for installation instructions.

  • Page 101: Smoke Alarm Verification

    Smoke Alarm Verification System Operation Conditions Required for a Release Output Activation Any release requires the activation of an interlock switch, and either a manual release switch or two activated addressable detectors. When these conditions are met, the “Release” and “General Alarm” outputs will activate, and the “Alert” output will deactivate. Inputs Output Results 1st Addressable Detector...

  • Page 102: 4: Using A Recorded F-Key Macro

    This option is programmable for each output group Map through the HFSS Honeywell Fire Software Suite. When an F-Key is active and a map in the system is set to be disabled by Map Inhibit, the system will show a trouble event.

  • Page 103: Section 10: Reporting

    ID formats. 10.1 Receivers Compatible with the Control Panel Table 10.1 shows receivers compatible with the control panel. Manufacturer Model Format Silent Knight by Honeywell Model 9800 SIA and Contact ID Model 9000 (SIA formats) Honeywell Security AlarmNet 7810-ir...
  • Page 104 Reporting Receivers Compatible with the Control Panel SIA Reporting Format Contact ID Reporting Format SIA pi Modifier Event Description Module ID Parameter Fixed Length Qualifier Event Group # Contact # # (If Any) Event Format NN - panel Code Codes XX- SBUS ID ZZZ- Zone # PPPP- Point #...
  • Page 105 Receivers Compatible with the Control Panel Reporting SIA Reporting Format Contact ID Reporting Format SIA pi Modifier Event Description Module ID Parameter Fixed Length Qualifier Event Group # Contact # # (If Any) Event Format NN - panel Code Codes XX- SBUS ID ZZZ- Zone # PPPP- Point #...
  • Page 106 Reporting Receivers Compatible with the Control Panel SIA Reporting Format Contact ID Reporting Format SIA pi Modifier Event Description Module ID Parameter Fixed Length Qualifier Event Group # Contact # # (If Any) Event Format NN - panel Code Codes XX- SBUS ID ZZZ- Zone # PPPP- Point #...
  • Page 107 Receivers Compatible with the Control Panel Reporting SIA Reporting Format Contact ID Reporting Format SIA pi Modifier Event Description Module ID Parameter Fixed Length Qualifier Event Group # Contact # # (If Any) Event Format NN - panel Code Codes XX- SBUS ID ZZZ- Zone # PPPP- Point #...
  • Page 108 Reporting Receivers Compatible with the Control Panel SIA Reporting Format Contact ID Reporting Format SIA pi Modifier Event Description Module ID Parameter Fixed Length Qualifier Event Group # Contact # # (If Any) Event Format NN - panel Code Codes XX- SBUS ID ZZZ- Zone # PPPP- Point #...
  • Page 109 Receivers Compatible with the Control Panel Reporting SIA Reporting Format Contact ID Reporting Format SIA pi Modifier Event Description Module ID Parameter Fixed Length Qualifier Event Group # Contact # # (If Any) Event Format NN - panel Code Codes XX- SBUS ID ZZZ- Zone # PPPP- Point #...
  • Page 110 Reporting Receivers Compatible with the Control Panel SIA Reporting Format Contact ID Reporting Format SIA pi Modifier Event Description Module ID Parameter Fixed Length Qualifier Event Group # Contact # # (If Any) Event Format NN - panel Code Codes XX- SBUS ID ZZZ- Zone # PPPP- Point #...
  • Page 111 Receivers Compatible with the Control Panel Reporting SIA Reporting Format Contact ID Reporting Format SIA pi Modifier Event Description Module ID Parameter Fixed Length Qualifier Event Group # Contact # # (If Any) Event Format NN - panel Code Codes XX- SBUS ID ZZZ- Zone # PPPP- Point #...

  • Page 112: Sia / 6700 Panels Pi Modifier Reporting

    Reporting SIA / 6700 Panels PI Modifier Reporting 10.2 SIA / 6700 Panels PI Modifier Reporting Events are sent to the Central Station as a variable length string: The Event Format is: EEZZZZ Where the Event Format is defined as follows: Code Event Code Description Event Code (2 characters)

  • Page 113: Sia- 6700 Panel Communicator

    SIA– 6700 Panel Communicator Reporting 10.3 SIA– 6700 Panel Communicator (Differences/additional features are underlined). Events are sent to the Central Station Receiver as a fixed length string. The event format is: EEPPMMZZZZ where the event format is defined as follows: Code Event Code Description Event code (2 characters)

  • Page 114: Section 11: Testing And Troubleshooting

    Section 11: Testing and Troubleshooting 11.1 Troubleshooting This section of the manual offers suggestions for troubleshooting hardware problems. Please read this section if you encounter a problem when you install the fire alarm control panel. If these suggestions do not solve your problem or if you encounter a problem that is not listed, contact Silent Knight technical support for assistance.

  • Page 115: 2: Event History

    Built-in Troubleshooting and Testing Tools Testing and Troubleshooting Measure the battery voltage while the notification appliances are sounding. Replace any battery with terminal voltage less than 85% of rat- ing. Reapply the AC power and reset the system. 11.2.2 Event History The event history can be useful for tracking or recalling a trouble condition.

  • Page 116: 3: I/O Point Control

    Testing and Troubleshooting Earth Fault Resistance Press the left arrow key to exit the SLC multi-locater function. NOTE: The system will resume normal operation once you exit SLC Device Locater. 11.3.3 I/O Point Control This feature allows you to toggle any output on or off and trip any input device. This option can be useful to test a point’s output mapping. I/O Point Control can only be accessed if enabled in the user profile.

  • Page 117: Section 12: Installation Records

    Section 12: Installation Records Use this section of the manual as a reference list to track how points, zones, and groups are programmed. 12.1 SD SLC Device Point Record You can use Table 12.1 to keep track of SD SLC device points. Default addresses for ID: Onboard: = 97 Zone / Module Addr...

  • Page 118: Slc Device Point Record

    Installation Records SK SLC Device Point Record 12.2 SK SLC Device Point Record You can use Table 12.2 and to keep track of SK SLC detectors and modules. Default addresses for ID: Onboard: = 97 Zone / Detector Addr Description Detector Addr Zone/ Group...

  • Page 119: Appendix A: Editing Text Using The Built-In Programmer

    Appendix A: Editing Text Using the Built-In Programmer This section contains the tables of programmable characters that may be used for the device, module, site, template, group, and zone names. T9 style editing is used. A.1 Characters Used for Editing Text Table A.1 lists the available characters and their associated numeric designator.

  • Page 120: Appendix B: Expanded Receiver/Panel Relationship

    Appendix B: Expanded Receiver/Panel Relationship The available Receiver Number will correspond with the panel number you entered. The Receiver Numbers are populated based on the panel number and they are audited to allow only the four appropriate receivers. See Section 6.2.6. Panel Available Receiver Numbers Table B.1 Receiver/Panel Relationship...

  • Page 121: Appendix C: Cadence Patterns

    Appendix C: Cadence Patterns Table C.1 shows the cadence patterns available for use with the control panel. Name Pattern Description (Patterns repeat until condition is cleared.) Constant Continuous sound (This is the only pattern that can be used for relay circuits. The system will override any other choice.) March Time 0.5 second on, 0.5 second off...

  • Page 122: Appendix D: Panel Security

    Appendix D: Panel Security Panel Installation / Maintenance Security Checklist System Description: ________________________________________________________________ System Location: __________________________________________________________________ Installer: _________________________________________________ Date: ___________________ Complete the following Cybersecurity Tasks for Each Panel Installation • Install the panel in a secure location considering both software and hardware vulnerabilities. •...

  • Page 123: Model 6700 Basic Operating Instructions

    Model 6700 Basic Operating Instructions These instructions must be framed and displayed next to the 6700 panel in accordance with NFPA 72 fire code for Local Protected Fire Alarm Systems. Test the system in accordance to NFPA 72. Operation Task to Perform Silence Alarms and Troubles Press SILENCE and then enter a code if prompted.
  • Page 125 Manufacturer Warranties and Limitation of Liability Manufacturer Warranties. Subject to the limitations set forth herein, Manufacturer warrants that the Products manufactured by it in its Northford, Connecticut facility and sold by it to its authorized Distributors shall be free, under normal use and service, from defects in material and workmanship for a period of thirty six months (36) months from the date of manufacture (effective Jan.
  • Page 126 Honeywell Silent Knight 12 Clintonville Road Northford, CT 06472-1610 203.484.7161 LS10148-001SK-E | F | 08-22 www.silentknight.com ©2023 Honeywell International Inc.

Table of Contents