Available languages
Available languages
Quick Links
ENG LI SH
INSTALLATION AND MAINTENANCE INSTRUCTIONS
TC809EA1035 Monitor Module
SPECIFICATIONS
Communications Loop
Nominal Operating Voltage:
15-32 VDC
Average Operating Current:
400 µA, 1 comm. every 5 seconds,
(Standard 47K EOL)
Maximum Alarm Current
600 µA
Monitoring Line
EOL Resistance:
47K Ohms Standard
Maximum Wiring Resistance:
1.5K Ohms
Maximum Voltage to EOL:
11 Volts
Maximum Short Circuit Current:
217 µA
BEFORE INSTALLING
This information is included as a quick reference installation guide. Refer
to the control panel installation manual for detailed system information.
If the modules will be installed in an existing operational system, inform
the operator and local authority that the system will be temporarily out
of service. Disconnect power to the control panel before installing the
modules.
NOTICE: This manual should be left with the owner/user of this
equipment.
GENERAL DESCRIPTION
The TC809EA1035 monitor module can be installed in a single gang
junction box directly behind the monitored unit. Its small size and light
weight allow it to be installed without rigid mounting (see Figure 1). The
TC809EA1035 is intended for use in intelligent, two-wire systems where
the individual address of each module is selected using rotary decade
switches. It provides a two-wire initiating circuit for normally open
contact fire alarm and security devices.
COMPATIBILITY REQUIREMENTS
To ensure proper operation, this module should only be connected to a
compatible control panel.
FIGURE 1:
C01063-00
1
Honeywell Building Solutions
Honeywell House, Arlington Business Park
Bracknell, Berkshire
RG12 1EB, UK
General
Temperature Range:
-10°C to 55°C
Humidity:
10% to 93% Non-condensing
Dimensions:
33mm H x 71mm W x 15mm D
Wire Length:
150mm minimum
MOUNTING AND WIRING
NOTE: This module is intended to be wired and mounted without rigid
connections inside a standard electrical box. All wiring must conform to
applicable local codes and regulations.
1.
Connect the red (+) and black ( – ) wires to the positive and negative
leads of the communication loop.
2.
Connect the violet (+) and yellow ( – ) wires to a two-wire, normally
open monitoring line.
3.
Install the specified EOL resistor value to terminate the monitoring
line. The EOL resistor for standard use is 47K Ohms – the other
resistors are for special use only.
4.
Set the address on the module per job drawings.
5.
Install the module in the desired mounting location.
FIGURE 2. TYPICAL CIRCUIT CONFIGURATION:
COMPATIBLE
FIRE DETECTION AND
CONTROL
ALARM SYSTEM LOOP
PANEL
COMMUNICATION LOOP
TO
(+)
NEXT
(–)
DEVICE
(+)
(–)
)
( +
)
( –
ALL WIRING
6 7 8 9
7 8
6
9
5
5
10
4
4
11
3
12
3
SHOWN IS
13
2
2
1
1
14
0
0
15
SUPERVISED AND
POWER LIMITED
EOL
VIOLET
RESISTOR
YELLOW
INCLUDED
MONITORING LINE
(47K OHMS
47k EOL
STANDARD
INCLUDED
- ELR-47K)
(ELR-47k)
C0614-05
EN 54-18: 2005
0359
DOP-IOD005
Input Output Device
13
TC809EA1035
Ave. Valle del Cedro No. 1681, Parque Industrial Intermex
Ciudad Juárez, Chihuahua, CP 32574, Mexico
Related Manuals for Honeywell TC809EA1035
Summary of Contents for Honeywell TC809EA1035
- Page 1 GENERAL DESCRIPTION line. The EOL resistor for standard use is 47K Ohms – the other The TC809EA1035 monitor module can be installed in a single gang resistors are for special use only. junction box directly behind the monitored unit. Its small size and light Set the address on the module per job drawings.
- Page 2 47 k ohm. Le altre resistenze sono solo per utilizzi speciali. DESCRIZIONE GENERALE Impostare l'indirizzo sul modulo secondo i disegni. Il modulo di controllo TC809EA1035 può essere installato in una scatola di Installare il modulo nella posizione di montaggio desiderata. connessione singola direttamente dietro l'unità monitorata. Le dimensioni contenute e il peso ridotto ne consentono l'installazione senza supporto FIGURA 2.
-
Page 3: Especificaciones
(véase la Figura 1). El TC809EA1035 está diseñado para su uso en Defina la dirección del módulo por dibujo del trabajo. sistemas de dos cables inteligentes en los que la dirección individual de Instale el módulo en la ubicación de montaje que desee. -
Page 4: Spezifikationen
Dank der kompakten Abmessungen und des geringen Gewichts kann die Installation des Moduls ohne starre Verbindungen erfolgen ABBILDUNG 2 – TYPISCHE SCHALTKREISKONFIGURATION (siehe Abbildung 1). Das TC809EA1035 Modul ist für den Einsatz in intelligenten Zweileitungssystemen vorgesehen, in denen die individuelle KOMPATIBLE BRANDMELDER- Adresse jedes Moduls über Dekaden-Drehschalter gewählt wird. - Page 5 Petit et léger, il Installer le module à l'endroit de votre choix. peut être installé sans connexion rigide (voir la Figure 1). Le TC809EA1035 est prévu pour les systèmes intelligents à 2 fils dans lesquels l'adresse de chaque module est sélectionnée au moyen des commutateurs rotatifs...