Panasonic SF4C Series Instruction Manual
Ultraslim light curtain/type4
Hide thumbs
Also See for SF4C Series:
- Instruction manual (143 pages) ,
- Quick instruction manual (116 pages)
Table of Contents
Quick Links
Ultraslim Light Curtain / Type4
SF4C Series
Instruction Manual
WUME-SF4C-11
Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]
Table of Contents
Troubleshooting
Related Manuals for Panasonic SF4C Series
Summary of Contents for Panasonic SF4C Series
-
Page 1
Ultraslim Light Curtain / Type4 SF4C Series
Instruction Manual WUME-SF4C-11 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]... - Page 2 (MEMO) © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]...
- Page 3 3) Though we have carefully drawn up the contents of this instruction manual, if there are any aspects that are not clear, or any error that you may notice, please contact our local Panasonic Industrial De- vices SUNX office of the nearest distributor.
-
Page 4: Table Of Contents
3-10 Functions Using Handy Controller SFC-HC (Optional) ·············································62 Chapter 4 Maintenance ·························································································· 69 4-1 Daily Inspection ·································································································69 4-2 Periodic Inspection (Every Six Months) ···································································70 4-3 Inspection after Maintenance ················································································70 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]... - Page 5 6-3-5 In Case Mounting with Protective Metal Case ······················································85 6-3-6 Mounting Bracket ···························································································86 Chapter 7 Others ·································································································· 89 7-1 Glossary ··········································································································89 7-2 CE Marking Declaration of Conformity ····································································90 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]...
-
Page 6: Chapter 1 Introduction
■ Before using this device, check whether the device performs properly with the functions and capabilities as per the design specifications. ■ In case of disposal, dispose this device as an industrial waste. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]... - Page 7 ● Do not use any reflection type or recursive reflection type arrangement. ● The corresponding emitter and receiver must have the same serial No. and be correctly oriented. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]...
- Page 8 ● Do not use this device to detect objects flying over the sensing area. ● Do not use this device to detect transparent objects, translucent objects or objects smaller than the specified minimum sensing objects. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]...
-
Page 9: Applicable Standards / Regulations
1 pc. each □ Test rod 1 pc. SF4C-F□: SF4C-TR14 (ø14 × 220mm), SF4C-H□: SF4C-TR25 (ø25 × 220mm) □ Abridged Instruction Manual 1 pc. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]... -
Page 10: Chapter 2 Before Using This Device
The mounting brackets are attached to this device. This brackets are to be used for mounting both emitter and receiver. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]... - Page 11 Also, incident light indicator turns off when setting blanking. For details, refer to “3-10 Functions Using Handy Controller SFC-HC (optional).” 6) The description given in [ ] is marked on the device. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]...
-
Page 12: Protection Area
Sensing Protective structure area Dangerous Dangerous part part Sensing area Sensing area Sensing area Dangerous Dangerous part part © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]... -
Page 13: Safety Distance
ø45mm ø65mm ø85mm (20mm-beam channel pitch type) Note: For details of the floating blanking function, refer to “3-10 Functions Using Handy Controller SFC-HC (option).” © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]... - Page 14 : Response time of this device (sec.) SF4C : Additional distance calculated from the size of the minimum sensing object of the device (mm) C = 850 (mm) © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]...
- Page 15 S = 1,600 × T + 99.2 = 1,600 × 0.4 + 99.2 = 739.2 Since this value matches with the case 5) above, S is 739.2 (mm). © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]...
- Page 16 Since the calculation above is performed by taking 1 (inch) = 25.4 (mm), there is a slight difference between the repre- sentation in (mm) and that in (inch). Refer to the relevant standard for the details. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]...
-
Page 17: Influence Of Reflective Surfaces
Reflective ceiling Reflective surface 0.16m Emitter Receiver 0.16m Emitter Receiver Sensing range 0.1 to 3m Sensing range 0.1 to 3m 0.16m Reflective floor © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]... -
Page 18: Device Placement
Position the emitter and receiver so that their cables are aligned. Failure to do so will cause the system to malfunction. Cable Cable Cable Cable © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]... -
Page 19: Mounting
● Install the standard mounting brackets in the mounting surface with two hexagon-socket head bolts [M5 (purchase separately)]. Hexagon-socket head bolt [M5 (Purchase separately)] This device © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]... -
Page 20
Note: SF4C-H28□ ,SF4C-H32□, SF4C-F55□ and SF4C-F63□ require multifunctional intermediate supporting bracket MS-SFC-4 (optional). Refer to
for the mounting method. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]... - Page 21 Step 4 Change direction of the part A of multifunctional mounting bracket. And tighten the two of hexagon- socket head bolts for beam-axis alignment M3 (length 5mm)]. The tightening torque should be 2N·m. Part A © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]...
-
Page 22
Note: SF4C-H28□ ,SF4C-H32□, SF4C-F55□ and SF4C-F63□ require multifunctional intermediate supporting bracket MS-SFC-4 (optional). Refer to
for the mounting method. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]... - Page 23 Use the multifunctional intermediate supporting bracket MS-SFC-4 (optional) in combination with the multifunctional mounting bracket MS-SFC-3 (optional). It cannot be mounted in conbination the standerd mountign bracket MS-SFC-1 (accesory). © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]...
- Page 24 MS-SFC-1 (accessory) is mounted as the dead space less mounting, the protective metal case MS-SFCH-□ (optional) can not be mounted to this device. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]...
-
Page 25: Wiring
6) In case a surge is generated, take countermeasures such as connecting a surge absorber to the origin of the surge. 7) Power supply unit corresponding to CLASS 2 (only for requiring TÜV Mark conformation). © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]... -
Page 26: I/O Circuit Diagrams And Output Waveform
2 wire (gray / black) and +V. 3) Vs is the applying supply voltage. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]... - Page 27 2) Large multi-purpose indicator lights up in red when connecting large multi-purpose indicator input 1 wire (gray) and 0V, and large multi-purpose indicator lights up in green when connecting large multi-purpose indicator input 2 wire (gray / black) and 0V. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]...
- Page 28 Control output 2 (OSSD 2) Approx. 35 to 75μs Approx. 35 to 75μs Approx. 40μs *↑ This OFF pulse appears in every 5 second cycle. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]...
-
Page 29: Wiring / Connecting Procedures And Terminal Arrangement
Connector for emitter: Gray, connector for receiver: Black ● For details of the cable with connector on one end and the cable with connector on both ends, refer to “6-2 Options.” © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]... -
Page 30: Basic Wiring
(Gray) Large multi-purpose indicator input 1 (Gray / Black) Large multi-purpose indicator input 2 Interlock function Invalid (Auto-reset) External device monitor function Invalid Auxiliary output Cannot be used © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]... - Page 31 (Gray) Large multi-purpose indicator input 1 (Gray / Black) Large multi-purpose indicator input 2 Interlock function Invalid (Auto-reset) External device monitor function Invalid Auxiliary output Cannot be used © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]...
-
Page 32: Wiring For Manual Reset (Interlock Is Valid)
K1, K2: External device (Forced guided relay or magnetic contactor) Notes: 1) Vs is the applying supply voltage. 2) For resetting, refer to “3-2 Interlock Function.” © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]... - Page 33 0 to +2.5V (source current 5mA or less): OFF, Open: ON K1, K2: External device (Forced guided relay or magnetic contactor) Note: For resetting, refer to “3-2 Interlock Function.” © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]...
-
Page 34: Wiring For Auto Reset (Interlock Is Invalid)
K1, K2: External device (Forced guided relay or magnetic contactor) Notes: 1) Vs is the applying supply voltage. 2) For resetting, refer to “3-2 Interlock Function.” © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]... - Page 35 0 to +2.5V (source current 5mA or less): ON, Open: OFF K1, K2: External device (Forced guided relay or magnetic contactor) Note: For resetting, refer to “3-2 Interlock Function.” © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]...
-
Page 36: Wiring Configuration For Valid Safety Input Function
Short-circuit (sink current 5 to 10mA), Source current 5 to 10mA: Valid External device monitor function Invalid Open: Invalid Auxiliary output Cannot be used * Symbols K1, K2: Safety relay unit etc. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]... - Page 37 Short-circuit (sink current 5 to 10mA), Source current 5 to 10mA: Valid External device monitor function Invalid Open: Invalid Auxiliary output Cannot be used * Symbols K1, K2: Safety relay unit etc. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]...
-
Page 38: Wiring Configuration For Invalid External Device Monitor Function
Vs to Vs - 3.5V (sink current 5mA or less): ON (Note), Open: OFF K1, K2: Safety relay unit etc. Note: Vs is the applying supply voltage. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]... - Page 39 Switch S1 ● Test input / Reset input 0 to +2.5V (source current 5mA or less): ON, Open: OFF K1, K2: Safety relay unit etc. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]...
-
Page 40: Wiring Configuration For Valid Muting Function
Notes: 1) The incandescent lamp or LED with total 1.5 to 6W or less shall be used when connecting lamp to the muting lamp output. 2) Vs is the applying supply voltage. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]... - Page 41 Note: The incandescent lamp or LED with total 1.5 to 6W or less shall be used when connecting to lamp the muting lamp output. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]...
-
Page 42: Adjustment
MS-SFC-4 (optional) for hexagon-socket head bolt for beam-axis adjustment [M3 (length: 5mm)] Multifunctional mounting bracket MS-SFC-3 (optional) for hexagon-socket head bolt for beam-axis adjustment [M3 (length: 5mm)] © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]... - Page 43 Refer to “2-6-2 Operation Test” for details. After beam-axis alignment, confirm that all bolts are tightened at stated torque. Refer to “2-4 Mounting” for each tightening torque of the bolts. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]...
-
Page 44: Operation Test
If the indicators show reception of the light even though the test rod blocks the light, check whether there is any reflec- tive object or extraneous light source near this device or not. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]... -
Page 45: Operation
3) Since the color of the operation indicator changes according to the ON / OFF state of the control output (OSSD 1 / 2), the operation indicator is marked as OSSD on the device. Digital error indicator © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]... - Page 46 4) Since the color of the operation indicator changes according to the ON / OFF state of the control output (OSSD 1 / 2), the operation indicator is marked as OSSD on the device. Digital error indicator © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]...
- Page 47 (Source of error): The control output (OSSD 1 / 2) short-circuit, extraneous light detection, sensor failure, etc. Refer to “Chapter 5 Troubleshooting” and remove the source of error. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]...
- Page 48 1 wire (gray) and the safety input 2 wire (gray / black). Take care that if only one wire is connected, the device may not operate normally. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]...
- Page 49 3) Since the color of the operation indicator changes according to the ON / OFF state of the control output (OSSD 1 / 2), the operation indicator is marked as OSSD on the device. Digital error indicator © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]...
-
Page 50: Chapter 3 Functions
(EN 60204-1)It is possible to change the conditions for interlocking by using the handy controller SFC-HC (optional). © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]... -
Page 51: Test Input Function
Control output (OSSD 1 / 2) Do not use the test input function for the purpose of stopping the machine in which the SF4C series is installed. Failure to do so could result in death or serious injury. © Panasonic Industrial Devices SUNX Co., Ltd. 2016... -
Page 52: Safety Input Function
SF4C series cable to the safety input 1 / 2. ● When extending the cable of other SF4C series which is connected to the safety input 1 / 2, use the exclusive cable and the total cable length should be 40.5m or less (for each emitter / receiver). If the total cable length is exceeding 40.5m, the device may malfunction, resulting in death or serious injury. - Page 53 (Orange) Synchronization + (Brown) +V (Blue) 0V ● Safety input Short-circuit (sink current 5 to 10mA, source current 5 to 10mA): Valid, Open: Invalid © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]...
-
Page 54: Large Multi-Purpose Indicator Function
(with black line) (Orange) Synchronization + (Brown) +V (Blue) 0V (Gray) Large multi-purpose indicator input 1 or (Gray / Black) Large multi-purpose indicator input 2 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]... -
Page 55: Auxiliary Output (Non-Safety Output)
T: SF4C-F□: 9ms or less, SF4C-H□: 7ms or less Do not use the auxiliary output for the purpose of stopping the machine in which the SF4C series is installed. Failure to do so could result in death or serious injury. -
Page 56: External Device Monitor Function
90ms or less Light Light received received status Light blocked Control output (OSSD 1 / 2) 300ms External device monitor input Lockout status © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]... -
Page 57: Muting Function
© Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]... -
Page 58
Muting sensor Muting input 1 Muting input 2
Muting sensor Muting sensor Muting sensor Muting sensor Muting input 1 Muting input 2 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]... - Page 59 ● It is recommended that two muting lamps should be connected in parallel. In this case, take care not to exceed total 6W or less. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]...
-
Page 60: Override Function
● Using override function, make sure that there exist no operator in the dangerous zone, which may result in death or serious injury. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]... - Page 61 When the muting lamp diagnosis function is invalid, the override function becomes valid 3 sec. after the input conditions of the muting sensor A (C) and B (D) were satisfied. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]...
-
Page 62: Functions Using Handy Controller Sfc-Hc (Optional)
The maximum continuous effective time can be set in the range of 1 to 600 sec. (in units of 1 sec.) or no limits. The factory setting is not limit. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]... - Page 63 4. The order for inputting the muting input 1 and 2 can be set and make the muting function valid by the order for inputting the muting input. At factory setting, the muting function is set to be valid whichever come first to input. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]...
- Page 64 (optional). • Invalid Safety input function can be set to invalid. In this case, safety contacting point and safety sensor can not be connected. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]...
- Page 65 SF4C series cable to the safety input 1 / 2. ● When extending the cable of other SF4C series which is connected to the safety input 1 / 2, use the exclusive cable and the total cable length should be 40.5m or less (for each emitter / receiver). If the total cable length is exceeding 40.5m, the device may malfunction, resulting in death or serious injury.
- Page 66 (White) Control output 2 (OSSD 2) (Shield) Output polarity setting wire (Blue) 0V ● Safety input Short-circuit (sink current 5 to 10mA): Valid, Open: Invalid © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]...
- Page 67 (Black) Control output 1 (OSSD 1) (White) Control output 2 (OSSD 2) (Blue) 0V ● Safety input Short-circuit (source current 5 to 10mA): Valid, Open: Invalid © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]...
- Page 68 The functional setting is not allowed to change without input of password. The factory setting is set to be invalid for the protective function. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]...
-
Page 69: Chapter 4 Maintenance
Be sure to check the operation of the muting function before its use. Furthermore, check the state of the muting lamp □ (cleanliness or brightness etc.) © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]... -
Page 70: Periodic Inspection (Every Six Months)
5) When the wiring method or wiring layout is changed. 6) When FSD (Final Switching Device) parts are replaced. 7) When FSD (Final Switching Device) setting is changed. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]... -
Page 71: Chapter 5 Troubleshooting
Wire the muting lamp output wire (red) to +V. correctly wired. Refer to “2-5 Wiring.” Output circuit error. Output circuit is damaged. Replace this device. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]... -
Page 72
The beam channels are not correctly aligned. Align the top / bottom direction of the beam channel between emitter and receiver. If the device does not work normally after checking the items above, please consult Panasonic Industrial De- vices SUNX.
... -
Page 73: Troubleshooting Of Receiver
Check if the auxiliary output wire (yellow-green / black) is discon- “invalid.” output is not nected or short-circuited. correctly Reset to factory default (mode 0) by using the handy controller operated. SFC-HC (optional). © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]... -
Page 74
The beam channels are not correctly aligned. Align the top / bottom direction of the beam channel between emitter and receiver. If the device does not work normally after checking the items above, please consult Panasonic Industrial De- vices SUNX.
... -
Page 75: Chapter 6 Specifications / Dimensions
1.30 × 10 1.53 × 10 MTTFd More than 100 years Weight (total of emitter and receiver) Approx. 630g Approx. 700g Approx. 760g Approx. 820g © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]... - Page 76 Weight (total of emitter and receiver) Approx. 490g Approx. 550g Approx. 610g PFHd: Probability of dangerous failure per hour, MTTFd: Mean time to dangerous failure © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]...
- Page 77 4) When using a muting lamp, extend the cable so that the total cable length is 30.5m or less (for each emitter / receiver). © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]...
- Page 78 The corresponding emitter and receiver must have the same serial NO. and be correctly oriented. The serial No. is indicated on the plates of both emitter and receiver. (Under the model represents the se- rial No.) © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]...
-
Page 79: Options
This mounting bracket is for replacing the MS-SFC-1 other Panasonic Industrial Devices SUNX area sensor NA2-N series. MS-SFC-2 With two M4 screws and one hexagon- socket head bolt [M6]. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]... - Page 80 In case using it to cable type SF4C-H□ / SF4C-F□, using cable shown below is useful. • Cable with connector on one end SFC-HC SFC-WNC1: 1 pc. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]...
-
Page 81: Dimension
In case of SF4C-F□, the position of digital indicator (red) is different as right figure. Also, digital indicator (red) is not incorporated in SF4C-F15□. Digital error indicator © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]... -
Page 82: In Case Mounting With Standard Mounting Brackets Without Dead Space
In case of SF4C-F□, the position of digital indicator (red) is different as right figure. Also, digital indicator (red) is not incorporated in SF4C-F15□. Digital error indicator © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]... -
Page 83: In Case Mounting With Multifunctional Mounting Bracket
In case of SF4C-F□, the position of digital indicator (red) is different as right figure. Also, digital indicator (red) is not incorporated in SF4C-F15□. Digital error indicator © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]... -
Page 84: In Case Mounting As Dead Space Mounting With Multifunctional Mounting Bracket
In case of SF4C-F□, the position of digital indicator (red) is different as right figure. Also, digital indicator (red) is not incorporated in SF4C-F15□. Digital error indicator © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]... -
Page 85: In Case Mounting With Protective Metal Case
In case of SF4C-F□, the position of digital indicator (red) is different as right figure. Also, digital indicator (red) is not incorporated in SF4C-F15□. Digital error indicator © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]... -
Page 86: Mounting Bracket
ø6.9 ø3.5 Material: Stainless steel 3) Multifunctional mounting bracket / MS-SFC-3 14.5 ø4.5 t 1.5 ø4.5 (13) 21.5 22.5 ø6.9 ø3.5 Material: Stainless steel © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]... - Page 87 7 23 (13) ø4.5 t 1.5 ø4.5 Material: Stainless steel 5) Multifunctional intermediate supporting bracket / MS-SFC-4 43.5 (31) 10.5 (13.6) 27.3 Material: Stainless steel © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]...
- Page 88 MS-SFCH-12 MS-SFCH-16 MS-SFCH-20 MS-SFCH-24 MS-SFCH-28 MS-SFCH-32 Material: Aluminum Protective metal case / MS-SFCH-8 ø6.4 ø6.4 36.2 ø5.4 ø5.4 4×ø4.8 43.5 43.5 19.6 Material: Aluminum © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]...
-
Page 89: Chapter 7 Others
The safety device that restarts automatically without any operation by the opera- tor after the device detects danger status and halts for a while. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]... -
Page 90: Ce Marking Declaration Of Conformity
Manufacturer’s Name: Panasonic Industrial Devices SUNX Co., Ltd. Manufacturer’s Address: 2431-1, Ushiyama-cho, Kasugai, Aichi 486-0901, Japan EU Representative’s Name: Panasonic Marketing Europe GmbH Panasonic Testing Center EU Representative’s Address: Winsbergring 15, 22525 Hamburg, Germany Product: Active Opto-electronic Protective Device (Light Curtain) - Page 91 Eighth edition : May 15, 2014 Ninth edition : January 15, 2015 Tenth edition : October 20, 2015 Eleventh edition : January 15, 2016 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]...
- Page 92 (MEMO) © Panasonic Industrial Devices SUNX Co., Ltd. 2016 Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]...
- Page 93 (iii) which was not discoverable by a person with the state-of-the-art scientific and technical knowledge at the time of manufacture; (iv) which was due to an operation or use by Purchaser outside of the limits of operation or environment specified by Panasonic In- dustrial Devices SUNX;...