Page 1
LIST Nos. LIST No. CG 25SC: xxx. 2014 CG 30SC: May 2015 PRODUCT NAME Hitachi 250 mm Grass Trimmer CG 25SC Model Hitachi 300 mm Grass Trimmer CG 30SC Model CONTENTS Page REPAIR GUIDE ----------------------------------------------------------------------------------------------------------------- 1 1. Precautions on disassembly and reassembly ----------------------------------------------------------- 1...
1. Precautions on disassembly and reassembly [Bold] and numbers in the description below correspond to the item numbers in the parts lists and exploded assembly diagrams of the Models CG 25SC and CG 30SC, respectively. Disassembly of the Model CG 25SC CAUTION: Be careful not to cut your finger with the Blade [51] located on the back of the Protecting Cover [50].
Page 3
(3) Remove the eight Screws ST4 x 16 [4] from Housing (R) [29] and Housing (L) [35]. Detach the Motor [39] with the Wire Roll Support [41], Button [32], Lock Pin [33], and Spring (C) [34] as shown in Fig. 3. (4) Remove the two Screws ST3 x 6 [30] from the Pipe Ass'y [24] to remove the Spacer [31] as shown in Fig.
Page 4
3. Disassembling the handle section (1) First, remove the Hanger Ass'y [16] and then Fig. 5 use a flat-blade screwdriver to pry off the Handle Ring [25]. Apply a piece NOTE: Apply a piece of cloth to the flat of cloth here. end of the screwdriver to protect parts.
Page 5
Reassembly of the Model CG 25SC Reverse the disassembly procedure to reassemble the Model CG 25SC. However, pay particular attention to the following. 1. Notices on reassembly (1) Press-fit the Wire Roll Support [41] to the Motor [39] until the Fig.
Page 6
2. Checking after reassembly (1) Check that the Lock Off Button [12] can be operated normally. Check that the trimmer does not operate just by pulling the Trigger [8]. (2) Push the Button [32] and check that Housing (R) [29] and Housing (L) [35] can be turned 180° and locked correctly.
Page 7
Disassembly of the Model CG 30SC CAUTION: Be careful not to cut your finger with the Blade <46> located on the back of the Protecting Cover <45>. 1. Disassembling the housing section (1) Open the Guide <44> wide and detach it from the housing Fig.
Page 8
(3) Remove the eight Screws ST4 x 16 <1> from Housing (R) <43> and Housing (L) <41>. Detach the Motor <37> with the Wire Roll Support <49>, Button <34>, Lock Pin <35>, and Spring (C) <36> as shown in Fig. 11. (4) Remove the two Screws ST3 x 6 <32>...
Page 9
3. Disassembling the handle section (1) Remove the eight Screws ST4 x 16 <1> from Handle (R) <2> and Handle (L) <13>. Remove the Trigger <6>, Spring (A) <5>, Spring (B) <3>, and the Lock Off Button <4> as shown in Fig. 13. (2) Remove the two Screws ST4 x 12 <11>...
Page 10
Cap <53> may fall off. <49> NOTE: The wire roll support of the Model CG 30SC is similar to that of the Model CG 25SC but they are not interchangeable (5-mm portion is slightly <52> different in shape.) Do not mismount.
4,000 VAC for 1 minute, with no abnormalities No-load current After no-load operation for five minutes, the no-load current value at a frequency of 50 Hz should be as follows: Model CG 25SC: 2.2 A (max.) Model CG 30SC: 2.3 A (max.) -10-...
Wiring diagram • Model CG 25SC Switch Black or white Red or blue Blue Black Cord Capacitor Black Brown Black or white Red or blue NOTE: *1: The color of the internal wire may be red or blue depending on the shipping conditions.
STANDARD REPAIR TIME (UNIT) SCHEDULES Variable MODEL 60 min. Fixed Work Flow CG 25SC Handle (R) Cord CG 30SC Handle (L) Cord Armor Trigger Lock Off Button Switch General assembly Housing (R) Spacer Housing (L) Button Motor Lock Pin Wire Roll Support Pipe Ass’y...