Table of Contents
Related Manuals for Honeywell SUTTON
Summary of Contents for Honeywell SUTTON
- Page 1 SUTTON 52” CEILING FAN MODELS #50188, 50189, 50190 Español p. 19 Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-877-361-3883, Monday - Thursday, 8 am - 6 pm, EST and Friday, 8 am - 5 pm, EST.
-
Page 2: Table Of Contents
WELCOME TABLE OF CONTENTS PREPARATION Before beginning the assembly of this product, ensure Care and Maintenance ......2 that all parts are present. -
Page 3: Package Contents
PACKAGE CONTENTS Unpack your fan and check the contents. You should have the following items: 1. Blade (5) 2. Canopy 3. Mounting Bracket 4. Canopy Cover 5. Downrod 6. Motor Housing 7. Switch Housing 8. Yoke Cover 9. Blade Arm (5) 10. -
Page 4: Safety Information
SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate, or install the product. • Before you begin installing the fan, disconnect the power by removing fuses or turning off the circuit breakers. • Make sure that all electrical connections comply with local codes, ordinances, the National Electrical Code, and ANSI/NFPA 70-199. -
Page 5: Mounting Options
MOUNTING OPTIONS DANGER Fig. 1 Turn off the circuit breakers and the wall switch to the fan supply line leads. Failure to disconnect the power supply prior to installation may result in serious injury or death. 1. Your fan has 3 mounting options: •... -
Page 6: Mounting Bracket Installation
MOUNTING BRACKET INSTALLATION 4. Loosen all four mounting bracket screws. Remove Fig. 4 the two mounting bracket screws and washers from the round holes of canopy. Set aside for later use. Mounting Mounting Detach mounting bracket from canopy (Fig. 4). Bracket Bracket Screws... -
Page 7: Standard Or Angle Mounting Instructions
STANDARD OR ANGLE MOUNTING INSTRUCTIONS 6. Partially loosen the two set screws in the yoke at Fig. 6 the top of the motor housing (Fig. 6). Set Screws Fig. 7 7. Remove the downrod pin and downrod clip from the downrod (Fig. 7). Downrod Clip Downrod Pin... - Page 8 STANDARD OR ANGLE MOUNTING INSTRUCTIONS 9. Slide the downrod into the yoke of the motor Fig. 9 Downrod housing, align the holes, and reinstall the downrod pin and downrod clip. Then retighten the two set screws (Fig. 9). Downrod Downrod Clip Downrod Pin Set Screw...
- Page 9 STANDARD OR ANGLE MOUNTING INSTRUCTIONS 12. Install the ball end of the downrod into the Fig. 12 mounting bracket opening. Align the slot in the ball with the tab in the mounting bracket. The downrod should not rotate if installed correctly (Fig. 12). Slot Mounting Bracket...
-
Page 10: Closemount Instructions
CLOSEMOUNT INSTRUCTIONS 13. Remove the canopy cover from the bottom of the Fig. 13 canopy (Fig. 13) Helpful Hint: The downrod and canopy cover are not used in this type of installation. Canopy Cover Canopy 14. Align the canopy with the closemount screw holes Fig. -
Page 11: Wiring
WIRING CAUTION Fig. 16 Be sure outlet box is properly grounded or that a ground (green or bare) wire is present. Black (live) WARNING White (neutral) If house wires are different colors than referred to in the following step, stop immediately. A professional Bare/Green (ground) electrician is recommended to determine wiring. -
Page 12: Canopy Installation
CANOPY INSTALLATION 17. Lift the canopy up so the partially installed mounting Fig. 17 bracket screws are situated in the L-slots on each side of the canopy. Rotate the canopy clockwise and install the two remaining mounting bracket screws and washers from Step 4 (Fig. 17). Mounting Mounting Bracket... -
Page 13: Blade Installation
BLADE INSTALLATION 18. Remove motor screws from underside of motor and Fig. 18 save for blade arm attachment. Discard the plastic motor blocks but keep the screws (Fig. 18). Motor Block Motor Screw Motor Block Motor Screw 19. The blades attach to blade arms using the Fast Fig. -
Page 14: Final Installation
FINAL INSTALLATION 21. Attach the pull chain extension to the pull chain Fig. 21 (Fig. 21). Pull Chain Extension Pull Chain Extension... -
Page 15: Operating Installation
OPERATING INSTRUCTIONS 22. Use the fan reverse switch, located on the side Fig. 22 of the light kit, to optimize your fan for seasonal performance (Fig. 22). Using a ceiling fan will allow you to raise your thermostat in the summer and lower your thermostat in the winter without sacrificing comfort. -
Page 16: Replacement Parts List
REPLACEMENT PARTS LIST For replacement parts, call the customer service department at 1-877-361-3883, 8 a.m. - 6 p.m., EST, Monday - Thursday, 8 a.m. - 5 p.m., EST, Friday. MODEL 50188 MODEL 50189 MODEL 50190 PIECE DESCRIPTION PART # PART # PART # Blade Arm 50188-A... -
Page 17: Troubleshooting
TROUBLESHOOTING At least twice each year, lower the canopy to check the downrod assembly, and then tighten all screws on the fan. Clean the motor housing with only a soft brush or lint-free cloth to avoid scratching the finish. Clean the blades with a lint-free cloth. You may occasionally apply a light coat of furniture polish to wood blades for added protection. -
Page 18: Limited Lifetime Warranty
Monday - Thursday, 8 am - 6 pm, EST and Friday, 8 am - 5 pm, EST. Please have a copy of the receipt as proof of purchase. The Honeywell Trademark is used under license from Honeywell Hong Kong China Electric Appliance Manufacture Co., Ltd.