Related Manuals for Honeywell SALERMO
Summary of Contents for Honeywell SALERMO
- Page 1 SALERMO 48” CEILING FAN MODEL #10285 Español p. 19 Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-877-361-3883, Monday - Thursday, 8 am - 6 pm, EST and Friday, 8 am - 5 pm, EST.
-
Page 2: Table Of Contents
WELCOME TABLE OF CONTENTS PREPARATION Before beginning the assembly of this product, ensure Care and Maintenance ......2 that all parts are present. -
Page 3: Package Contents
PACKAGE CONTENTS Unpack your fan and check the contents. You should have the following items: 1. Blade (3) 2. Mounting Bracket 3. Canopy 4. Canopy Cover 5. Yoke Cover 6. Downrod 7. Downrod Clip 8. Downrod Pin 9. Bulb (2) 10. -
Page 4: Safety Information
SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate, or install the product. • Before you begin installing the fan, disconnect the power by removing fuses or turning off the circuit breakers. • Make sure that all electrical connections comply with local codes, ordinances, the National Electrical Code, and ANSI/NFPA 70-199. -
Page 5: Mounting Options
MOUNTING OPTIONS 1. Your fan has 3 mounting options: Fig. 1 • Standard (Fig. 1) • Angle (Fig. 2) • Closemount (Fig. 3) Note: The fans in figures 1 through 3 are not the actual fan in your package, they are representation of the 3 different mounting options. -
Page 6: Mounting Bracket Installation
MOUNTING BRACKET INSTALLATION 4. Turn off the circuit breakers and wall switch leading Fig. 4 to the fan wire leads (Fig 4). WARNING Failure to disconnect the power supply prior to installation may result in serious injury or death. 5. Loosen all four mounting bracket screws and Fig. -
Page 7: Standard Or Angle Mounting Instructions
STANDARD OR ANGLE MOUNTING INSTRUCTIONS 7. Partially loosen the set screws in the yoke of the Fig. 7 motor assembly (Fig. 7). Set Screw Fig. 8 8. Remove the downrod clip and downrod pin from the downrod (Fig. 8). Downrod Clip Downrod Pin Downrod... - Page 8 STANDARD OR ANGLE MOUNTING INSTRUCTIONS 10. Slide the downrod into the yoke of the motor Fig. 10 assembly, align the holes, and reinstall the downrod pin and downrod clip. Then re-tighten the set screws with a Phillips screwdriver (Fig. 10). Downrod Set Screw Downrod...
- Page 9 STANDARD OR ANGLE MOUNTING INSTRUCTIONS 13. Install the ball end of the downrod into the Fig. 13 mounting bracket opening. Align the slot in the ball with the tab in the mounting bracket. If installed correctly, the downrod should not rotate in the mounting bracket (Fig.
-
Page 10: Closemount Instructions
CLOSEMOUNT INSTRUCTIONS 15. Remove the canopy cover from the bottom of the Fig. 15 canopy (Fig. 15). Helpful Hint: The downrod, yoke cover and canopy cover are not used in this type of installation. Canopy Cover Canopy 16. Align the canopy with the holes in the top of motor Fig. -
Page 11: Wiring
WIRING CAUTION Fig. 18 Be sure outlet box is properly grounded or that a Black (hot/power) ground (green or bare) wire is present. WARNING White (neutral) If house wires are different colors than referred to in Bare/Green the following steps, consult a professional electrician to determine wiring. -
Page 12: Canopy Installation
CANOPY INSTALLATION 19. Lift the canopy up so the partially installed mounting Fig. 19 bracket screws engage the J-slots on each side of the canopy. Rotate the canopy clockwise and install the previously removed mounting bracket screws from Step 5. Tighten all four screws with a Phillips screwdriver (Fig. -
Page 13: Light Kit Installation
LIGHT KIT INSTALLATION 21. Loosen two and completely remove one of the Fig. 21 pre-assembled fitter plate screws from the fitter plate. Connect the single-pin connector from the fan to the single-pin connector to the light kit -- blue to black and white to white. Single-pin Then, lift the light kit up until the two loosened Connector... -
Page 14: Remote Control
REMOTE CONTROL 24. Remove the battery cover (not shown) from the LED Indicator Fig. 24 back of the remote. Insert the battery into the remote; ensure polarity of battery matches the polarity indicated in the battery compartment -- positive (+) to positive (+) and negative (-) to Fan Power negative (-). -
Page 15: Operating Instructions
OPERATING INSTRUCTIONS 27. Use the reverse switch, located on the side of the Fig. 27 fan, to optimize your fan for seasonal performance (Fig. 27). Using a ceiling fan will allow you to raise your thermostat in the summer and lower your thermostat in the winter without sacrificing comfort. -
Page 16: Replacement Parts List
REPLACEMENT PARTS LIST For replacement parts, call the customer service department at 1-877-361-3883, 8 a.m. - 6 p.m., EST, Monday - Thursday, 8 a.m. - 5 p.m., EST, Friday. MODEL 10285 PIECE DESCRIPTION PART # Blade 10285-A Glass Bowl 10285-B Hardware bag (not shown) contains: Mounting hardware, blade attachment hardware,... -
Page 17: Troubleshooting
TROUBLESHOOTING At least twice each year, lower the canopy to check the downrod assembly, and then tighten all screws on the fan. Clean the motor housing with only a soft brush or lint-free cloth to avoid scratching the finish. Clean the blades with a lint-free cloth. You may occasionally apply a light coat of furniture polish to wood blades for added protection. -
Page 18: Limited Lifetime Warranty
1-877-361-3883 Monday - Thursday, 8 am - 6 pm, EST and Friday, 8 am - 5 pm, EST. Please have a copy of the receipt as proof of purchase. The Honeywell Trademark is used under license from Honeywell International Hong Kong China Electric Appliance Manufacture Co., Ltd.