Connecting the controller unit to the management hosts Connecting the units to the power supply Supported connections Turning on/off AC power Turning on AC power Turning off AC power Installing and configuring the storage array Bosch Security Systems B.V. 2020.09 | V2 | DOC Quick Installation Guide...
Permanently connected devices must have an external, readily operable mains plug or all‑pole mains switch in accordance with installation rules. – Pluggable devices must have an easily accessible socket-outlet installed near the equipment. 2020.09 | V2 | DOC Bosch Security Systems B.V. Quick Installation Guide...
Page 5
SELV circuits. – If safe operation of the unit cannot be ensured, remove it from service and secure it to prevent unauthorized operation. In such cases, have the unit checked by Bosch Security Systems. –...
Do not remove more than one canister from the enclosure while power to the enclosure is turned on. – Bosch products may contain Class 1 laser devices, Class 1M laser devices, or both. – Keep away from moving fan blades.
This is a class A product. In a domestic environment this product may cause radio interference, in which case the user may be required to take adequate measures. Bosch Security Systems B.V. 2020.09 | V2 | DOC Quick Installation Guide...
Page 8
DSA E-Series (E2800 12-bay) Notice! Video loss is inherent to digital video recording; therefore, Bosch Security Systems cannot be held liable for any damage that results from missing video information. To minimize the risk of losing information, we recommend multiple, redundant recording systems, and a procedure to back up all analog and digital information.
Parts included Make sure that all parts are included and not damaged. If the packaging or any parts are damaged, contact your shipper. If any parts are missing, contact your Bosch Security Systems Sales or Customer Service Representative. Base units...
Bosch Product Registration page. Registering your device using an existing NetApp NOW account Sign in to your NetApp NOW account and register your device here. Creating a new account using the Bosch Product Registration page Please register your product: https://www.boschsecurity.com/product-registration/...
Page 11
DSA E-Series (E2800 12-bay) Introduction | en More information For more information, software downloads, and documentation, go to www.boschsecurity.com and the corresponding product page. Bosch Security Systems B.V. 2020.09 | V2 | DOC Quick Installation Guide...
Status display Channel 5 (left) / Channel 6 (right) - Host interface ports (Dual 10 GB iSCSI, RJ45 Base‑T) Note: Use only RJ45 Base‑T ports or optical ports. Power-fan canister 1 On/off switch 2020.09 | V2 | DOC Bosch Security Systems B.V. Quick Installation Guide...
Page 13
Note: Use only RJ45 Base‑T ports or optical ports. Power-fan canister 1 On/off switch Mains connection 100 - 240 VAC Power-fan canister 2 12-bay expansion unit - rear view 11 12 13 Bosch Security Systems B.V. 2020.09 | V2 | DOC Quick Installation Guide...
Page 14
IOM B - SAS port 2 IOM B - SAS port 3 IOM B - SAS port 4 Power-fan canister 1 On/off switch Mains connection 100 - 240 VAC Power-fan canister 2 Refer to – Supported connections, page 22 2020.09 | V2 | DOC Bosch Security Systems B.V. Quick Installation Guide...
You can install the unit in either a square-hole or round-hole rack. – If you are installing the unit in a cabinet not provided by Bosch, you must calculate the thermal output of your equipment and compare the results with the target system cabinet's thermal rating.
Page 16
(preinstalled on either side of the front of the unit), the holes on the rack or system cabinet, and the holes on the front of rails. 2020.09 | V2 | DOC Bosch Security Systems B.V. Quick Installation Guide...
If applicable, replace the end caps or the system bezel. Note: Additional documentation can be found on the Bosch online catalog. Notice! Install the expansion units below and above the controller unit, keeping the weight in the lower portion of the cabinet.
Controller A IOM B IOM A Three expansion units - dual controller configuration Controller B Controller A IOM B IOM A IOM B IOM A IOM B IOM A 2020.09 | V2 | DOC Bosch Security Systems B.V. Quick Installation Guide...
Connecting the controller unit to the network In case of a Bosch Video Recording Solution a host is an IP camera. To connect the controller unit to the Ethernet one or two of two available iSCSI host ports must be connected to the Ethernet.
Connect Ethernet cables between port 1 of controller A and port 1 of controller B to an external Ethernet switch or hub. Connect the management host to the Ethernet switch or hub. 2020.09 | V2 | DOC Bosch Security Systems B.V. Quick Installation Guide...
To connect the controller unit and the expansion units to the power supply: Confirm that the two power switches on the controller unit are off. Note: If you have expansion units, confirm that their power switches are off. Bosch Security Systems B.V. 2020.09 | V2 | DOC Quick Installation Guide...
If any of the amber LEDs are on, there might be a problem with a component. Confirm you completed the installation steps correctly. If you are unable to resolve the problem, contact your local Bosch Technical Support team. Supported connections We recommend using the following connection methods: 2020.09 | V2 | DOC...
Page 23
Note: Reserved for maintenance operations if the hardware contains a second Ethernet port. Channel 3 / Controller A and Channel 4 / Controller A and Channel 3 / Controller B (iSCSI, Channel 4 / Controller B (iSCSI, optical) optical) Bosch Security Systems B.V. 2020.09 | V2 | DOC Quick Installation Guide...
Page 24
– Alternatively: iSCSI, optical Note: – Channel 3 / Controller B is the fallback of Channel 3 / Controller A and Channel 4 / Controller A is the fallback of Channel 4 /. Controller B 2020.09 | V2 | DOC Bosch Security Systems B.V. Quick Installation Guide...
If any of the amber LEDs are on, there might be a problem with a component. Confirm you completed the installation steps correctly. If you are unable to resolve the problem, contact your local Bosch Technical Support team. Connect all cables if required.
For the basic setup use the Video Recording Manager Configuration Manager software. For detailed information, in Configuration Manager refer to the Video Recording Manager Help. More information For more information, software downloads, and documentation, go to www.boschsecurity.com and the corresponding product page. 2020.09 | V2 | DOC Bosch Security Systems B.V. Quick Installation Guide...
Page 27
DSA E-Series (E2800 12-bay) Installing and configuring the storage array | Bosch Security Systems B.V. 2020.09 | V2 | DOC Quick Installation Guide...
Page 28
| Installing and configuring the storage array DSA E-Series (E2800 12-bay) 2020.09 | V2 | DOC Bosch Security Systems B.V. Quick Installation Guide...