Honeywell Pro-Watch 7000 Install Manual
Two-reader module
Hide thumbs
Also See for Pro-Watch 7000:
- Install manual (46 pages) ,
- Security manual (20 pages) ,
- Install manual (22 pages)
Table of Contents
Table of Contents
Related Manuals for Honeywell Pro-Watch 7000
Summary of Contents for Honeywell Pro-Watch 7000
- Page 1 Pro-Watch 7000 Two-Reader Module PW7K1R2 Install Guide...
- Page 2 All product and brand names are the service marks, trademarks, registered trademarks, or registered service marks of their respective owners. Printed in the United States of America. Honeywell reserves the right to change any information in this document at any time without prior notice.
-
Page 3: Table Of Contents
TABLE OF CONTENTS Notices............................iii Warnings and Cautions......................iii Disclaimer............................v Limited Warranty ........................v Confidentiality ......................... vi Compliance ..........................vi CE and WEEE Marking ......................vi Unpacking Procedure ......................vii Shipping Instructions ......................vii Chapter 1 - Reader Module ................9 Description............................ - Page 4 Appendix A - Programming Sheet............... 21 PW-7000 Two-Reader Module Installation Guide, Document 800-25676V1...
-
Page 5: Notices
DO NOT ACCEPT VERBAL APPROVALS, BECAUSE THEY ARE NOT VALID. Honeywell never recommends using the PW-7000 or related products for use as a primary warning or monitoring system. Primary warning or monitoring systems should always meet local fire and safety code requirements. - Page 6 Inc. Copyright laws of the United States protect all information in this document or in the software product itself. Note: Any use of this product is subject to the terms and acceptance of the Honeywell, Inc. Software Agreement. Please request a copy from Honeywell, Inc., and review the agreement carefully.
-
Page 7: Disclaimer
All Products sold or licensed by Honeywell include a warranty registration card which must be completed and returned to Honeywell by or on behalf of the end user in order for Honeywell to provide warranty service, repair, credit or exchange. -
Page 8: Confidentiality
Confidentiality All software, drawings, diagrams, specifications, catalogs, literature, manuals and other materials furnished by Honeywell relating to the design, use and service of the Products shall remain confidential and shall constitute proprietary rights of Honeywell and Customer agrees to treat such information as confidential. Cus-... -
Page 9: Unpacking Procedure
If shipping caused damage to the unit, a claim must be filed with the commercial carrier. If any other defect is apparent, call for a return authorization. Shipping Instructions To ship equipment back to Honeywell, Inc.: Step 1. Contact the customer service department at 800-323-4576 before returning equipment. When you call please have available: •... - Page 10 Step 2. From the customer service department, obtain the Return Authorization Number (RMA). Step 3. Show the RMA number on all packages shipped. Packages which are not marked with an RMA number will be refused at the factory and returned to you COD.
-
Page 11: Chapter 1 - Reader Module
CHAPTER READER MODULE Description The PW-7000Two-Reader Module provides support for up to two access control doors by providing connections for Wiegand or Clock/Data type readers, super- vised inputs, and relay outputs. You can either mount the board in a rack or open flat. -
Page 12: Specifications
Specifications The Two-Reader Module is for use in low voltage, class 2 circuits only. Primary power: • 12VDC + 10%, 650mA maximum with 5V readers, 300 mA max. excluding readers Relay contacts: • Relays 0 and 2 outputs, Form-C, 5A @ 30VDC, resistive •... -
Page 13: Setup
Setup Setting Jumpers Table 1: Jumper Settings Jumper Setting Default Selected Port 1 RS-485 EOL terminator is not active Port 1 RS-485 EOL terminator is active Reader 0 Power Terminal provides 5 VDC Reader 0 Power Terminal provides 12 VDC Reader 1 Power Terminal provides 5 VDC Reader 1 Power Terminal provides 12 VDC Setting DIP Switches... -
Page 14: Led Operation
Selection ADDRESS 25 ADDRESS 26 ADDRESS 27 ADDRESS 28 ADDRESS 29 ADDRESS 30 ADDRESS 31 Reserved 9,600 BPS 19,200 BPS 38,400 BPS* Not Used* * = Default LED Operation The Two-Reader Module uses two onboard LEDs (D1 and D2) to provide status information during the power-up sequence as well as during normal operation. -
Page 15: Power
Table 4: Additional PW7000 Two-Reader Module LEDs LED number Description Reader 0 activity Reader 1 activity Input 0 Input 1 Input 2 Input 3 Input 4 Input 5 Input 6 Input 7 Tamper Power Relay 0 status Relay 3 status Relay 2 status Relay 4 status Relay 1 status... -
Page 16: Wiring
Step 1. TR+ is the plus side of the transmit and receive differential signal. Step 2. TR- is the negative side of the transmit and receive differential signal. Step 3. GND is the signal ground.The wiring for this signal is required and NOT optional. - Page 17 Figure 1: PW-7000 Two-Reader Module Wiring: Connectors 1-7 Short Door Status TWO READER BOARD BLACK together* Switch IN4 COMMON WHITE Egress GREEN Push-Button IN5 COMMON Switch Typical Connection IN0 COMMON IN1 COMMON RELAY0 NO RELAY0 C Door Lock Suppressor RELAY0 NC BLACK RELAY1 NO RELAY1 C...
- Page 18 PW-7000 Two-Reader Module Wiring: Connectors 1, 7-9 Tamper Switch (In CLOSE TWO READER BOARD position when +12VDC Power Cabinet Door is Supply Closed) C - No Charging N/C - No Charging N/C - Low Battery IN6 Common C - Low Battery IN7 Common Relay 4 NC Relay 4 C...
-
Page 19: Reader Wiring
Reader Wiring The following Honeywell reader module numbers have been approved by UL for use with the PW7K1R2: OM40BHONA, OM55BHONA, OP10HONE, OP30HONE, OP40HONE, OP90HONE, OT30HONA, OT31HONA, OT35HONA, and OT36HONA. Each reader port supports a reader with TTL interface. Power to the reader is selectable as 5VDC or 12VDC (pass-through). -
Page 20: Control Output Wiring
By default, Input 0 is defined as the Door Status Input corresponding to reader 0 and Input 1 is defined as the REX input corresponding to reader 0. Also by default, Input 2 is defined as the Door Status Input corresponding to reader 1 and Input 3 is defined as the REX input corresponding to reader 1. -
Page 21: Mounting Options
Mounting Options This board can be mounted on-edge in the rack-mount enclosure provided by Honeywell or it can be mounted flat against any surface using standoffs under the mounting holes provided in each of the four corners of this board. - Page 22 This page is intentionally left blank PW-7000 Two-Reader Module Installation Guide, Document 800-25676V1...
- Page 23 APPENDIX PROGRAMMING SHEET PW-7000 2-Reader Input Module Programming Sheets: Project Name Location / Country Host IC Board Board Description PW Panel RS485 Port Board Address Location Floor Cabinet Location Tamper Input Connected Powerfail Shunted Termination Jumper J1 Not Active RS485 Port + Power Connector Connected Cable # Cable Destination...
- Page 24 Door 1 Input / Output Connected Cable # Cable Destination Conductor Color Input 0 Com Pin #2 Input 1 Pin #3 Input 1 Com Pin #4 Relay 0 No Pin #5 Relay 0 Com Pin #6 Relay 0 NC Pin #7 Relay 1 No Pin #8 Relay 1 Com...
- Page 25 Inputs 6 and 7 Connected Cable # Cable Destination Conductor Color Input 6 Pin #1 Input 6 Com Pin #2 Input 7 Pin #3 Input 7 Com Pin #4 Inputs 4 and 5 Connected Cable # Cable Destination Conductor Color Relay 4 NC Pin #1 Relay 4 Com...
- Page 26 This page is intentionally left blank PW-7000 Two-Reader Module Installation Guide, Document 800-25676V1...
- Page 28 Honeywell Integrated Security, 135 W. Forest Hill Avenue Oak Creek, WI 53154 United States 800-323-4576 414-766-1798 Fax www.security.honeywell.com Discover | Customer Portal Self-Service Product Support and Learning Management System https://honeywelldiscovertraining.com/login/discover/default.asp ™ YouTube | Honeywell Help and Support https://www.youtube.com/channel/UCBEL6ouNV_LN5lEpYRujMTg/featured Document 800-25676V1...