1. Manuals
  2. Brands
  3. GE Manuals
  4. Grill
  5. JGGN24
  6. Assembly instructions manual

GE JGGN24 Assembly Instructions Manual

Outdoor cooking center
Hide thumbs Also See for JGGN24:
Table of Contents

Quick Links

Assembly
Instructions
Questions? Call 866.GE.GRILL (866.434.7455)
BEFORE YOU BEGIN
Read these instructions completely and carefully.
IMPORTANT –
•
governing codes and ordinances.
Note to Assembler –
•
instructions with the Consumer.
Note to Consumer –
•
instructions for future reference.
• Skill level – Assembly of this grill requires basic
mechanical skills.
TOOLS YOU WILL NEED
Phillips screwdriver
7/16" open end wrench or deep socket with extension
Rubber mallet (optional)
Observe all
Be sure to leave these
Keep these
Block of wood or cardboard
(optional)
Outdoor Cooking
Center
JGGN24, JGGR24
www.GEAppliances.com
or
Visit our Website at:
• Proper assembly is the responsibility of the assembler.
• Product failure due to improper assembly is not
covered under the Warranty.
• If you received a damaged grill, you should contact
your dealer.
Note –
Grill must be completely assembled before
•
any gas connections are made.
KEEP THESE INSTRUCTIONS
1
READ CAREFULLY.
.
Table of Contents
loading

Related Manuals for GE JGGN24

Summary of Contents for GE JGGN24

  • Page 1 Assembly Outdoor Cooking Instructions Center JGGN24, JGGR24 Questions? Call 866.GE.GRILL (866.434.7455) www.GEAppliances.com Visit our Website at: BEFORE YOU BEGIN • Proper assembly is the responsibility of the assembler. Read these instructions completely and carefully. • Product failure due to improper assembly is not IMPORTANT –...

  • Page 2: Parts Included

    Assembly Instructions PARTS INCLUDED (Not all models have all parts) Handle with Spacer (2) Grill Body (1) Base Assembly (1) Handle Nut (2) Bin (1) Handle Bolt (2) Upper Rear Brace (1) Shelf Handle (1) Grease Cup Thumb Screw (2) Side Grid (1) Holder (1) Screw (2)

  • Page 3: Unpack The Grill

    Assembly Instructions 4. Grasp the pan on both sides and raise it up until NOTE TO ASSEMBLER the legs are standing squarely on the floor. To aid assembly, all parts in bold type in the following assembly steps match the illustrations shown in the PARTS INCLUDED section.

  • Page 4: Assemble The Lower Base

    Assembly Instructions 3. Slide a wheel axle bolt through a wheel, large wheel ASSEMBLE THE LOWER BASE washer, and through the top hole on the left leg. Secure the wheel in place by sliding a wheel clip through the hole in the wheel axle bolt. Repeat for the other leg.
  • Page 5 Assembly Instructions 4. Thread a large bolt into the front bottom hole on ASSEMBLE BASE TO GRILL BODY each side. Secure in place with wing nuts. Large Bolts Wing Wing Nut (10) Nuts Large Bolt (6) 1. Turn the grill body upside-down and wedge cardboard or a block of wood under the front side to prevent tipping during assembly.

  • Page 6: Install The Handles

    Assembly Instructions INSTALL THE HANDLES INSTALL THE SIDE SHELVES Handle Bolt (2) Handle Nut (2) • Slide a handle bolt through a handle and spacer Wing Nut (1 or 2) Large Bolt (1 or 2) and into the hole in the grill top. Align and tighten in place with a handle nut using a 7/16″...

  • Page 7: Install The Left Side Burner/Shelf

    Assembly Instructions 4. Remove the side grid and peel off the protective INSTALL THE LEFT SIDE shipping film, if present. Guide the two pins on the BURNER/SHELF (on some models) grid into the two holes in the side burner/shelf and lower it into position.

  • Page 8: Connect The Left Side Burner/Shelf

    Assembly Instructions 3. Hand connect the side burner electrode wire to CONNECT THE LEFT SIDE the connector under the control panel. BURNER/SHELF (The connector is under the control panel, (on some models) on the stem of the red igniter button). 1.

  • Page 9: Assemble The Grill Compartment

    Assembly Instructions 3. With the deflector on top (holes facing front), ASSEMBLE THE GRILL press the round end of the rotisserie burner (on COMPARTMENT some models) into the hole on the right. Press 1. Place the Flav-R-Wave® on the supports in the down and snap the left side into the two holes in bottom of the grill.

  • Page 10: Mount The Lp Tank

    Assembly Instructions INSTALL THE FRONT BANNER MOUNT THE LP TANK (not included—obtain locally) 1. Insert the pointed support of the front banner into the slot behind the front leg at the base. • Your grill is designed to be used with an LP NEW OPD HANDWHEEL gas tank equipped...

  • Page 11: Connect The Lp Tank

    Assembly Instructions TEST FOR LEAKS CONNECT THE LP TANK (CONTINUED) 1. Remove the plastic cover from the LP 5. Wet each connection with the soap solution. tank connector. 2. Screw the regulator coupling (on the gas hose) onto the LP tank connector in a clockwise direction. Hand tighten only.
  • Page 12 PARTS LIST...
  • Page 13 GENERAL ELECTRIC PARTS CATALOG REF. NO. PART NO. PART DESCRIPTION JGGN24 JGGR24 S11425 CASTING BOTTOM S11296 CASTING TOP 164D4388 NAMEPLATE 10571-6 HEAT INDICATOR S21235 HINGE PIN S21233 HINGE CLIP S12029 GRID S12207 GRID RETRACTABLE 10222-T425 FLAV-R-WAVE® S10017 BURNER ASSEMBLY 10342-21...
  • Page 14 ELECTRODE - SIDE BURNER 114. 10393-K40 COVER - SIDE BURNER 115. Y-29305 SCREW 10-24 x 3/8 117. 10393-K50 SHELF - SIDE BURNER 118. 10393-T221 SHIELD - SIDE BURNER 123. 10184-D60 CASTOR INSERT To obtain replacement parts, call during normal business hours: 866.GE.GRILL (866.434.7455).
  • Page 15 NOTES...
  • Page 16 Part No. 164D4290P034 Pub. No. 49-80076 04-01 JR Printed in Canada...

This manual is also suitable for:

Jggr24

Table of Contents