Assembly Outdoor Cooking Instructions Center JGGB27, JGGN27, JGGR27 Questions? Call 866.GE.GRILL (866.434.7455) www.GEAppliances.com Visit our Website at: BEFORE YOU BEGIN • Proper assembly is the responsibility of the assembler. Read these instructions completely and carefully. • Product failure due to improper assembly is not IMPORTANT –...
Assembly Instructions PARTS INCLUDED (Not all models have all parts) Rotisserie Lid (1) Burner (1) (on some models) Handle and Spacer (2) Handle Bolt (2) Nut (14) Grill Bottom (1) Lid Hinge Bolt (2) Clip (2) Swing Basket (1) (on some models) Grid Lifter (1) LP Tank Warming...
Assembly Instructions ASSEMBLE THE LOWER BASE NOTE TO ASSEMBLER 1. Peel off the protective shipping film from the front To aid assembly, all parts in bold type in the following panel, if present. assembly steps match the illustrations shown in the PARTS INCLUDED section.
Assembly Instructions MOUNT THE BASE TO THE MOUNT THE BASE CART GRILL BOTTOM Bolt (6) Nut (6) Nut (6) 1. Place the base cart over the lower base. 1. Place the grill bottom upside down on the floor and position the hoses as shown. 2.
Assembly Instructions INSTALL THE SIDE SHELVES SET THE GRILL ON ITS WHEELS 1. From the back side, lower the base to the floor. Large Bolt (1 or 2) Wing Nut (1 or 2) NOTE: If your model has a burner/shelf, it must be installed on the left side.
Assembly Instructions 3. Remove the side grid and peel off the protective INSTALL THE LEFT SIDE shipping film, if present. Guide the two pins on the BURNER/SHELF side grid into the two holes in the side (on some models) burner/shelf and lower it into position. Side burner grid Screw (2) Large Bolt (1)
Assembly Instructions 3. Connect the side burner electrode wire to CONNECT THE LEFT SIDE the connector under the control panel. (The BURNER/SHELF (on some models) connector is under the control panel, on the stem of the red igniter button). 1. Connect the side burner hose by pressing the fitting into the side burner gas tube.
Assembly Instructions INSTALL THE LID INSTALL THE HANDLES Lid Hinge Bolt (2) Clip (2) Handle Bolt (2) Nut (2) 1. Place and align the lid over the grill bottom in the • Slide a handle bolt through a handle and spacer closed position.
Assembly Instructions 3. Place the ends of the warming rack into the back ASSEMBLE THE GRILL slots on the upper grill sides. COMPARTMENT 1. Place the Flav-R-Wave® on the supports in the bottom of the grill. The Flav-R-Wave® should lie flat. Warming rack ®...
Assembly Instructions ATTACH THE LP TANK RETAINERS MOUNT THE LP TANK (not included—obtain locally) • Place the end of the LP tank retainer in the hole in the base. Flex the retainer and place the other • Your grill is designed end in the other hole in the base.
Assembly Instructions CONNECT THE LP TANK TEST FOR LEAKS (CONTINUED) 1. Remove the plastic cover from the LP 5. Wet each connection with the soap solution. tank connector. 2. Screw the regulator coupling (on the gas hose) onto the LP tank connector in a clockwise direction. Hand tighten only.
Page 13
GENERAL ELECTRIC PARTS CATALOG REF. NO. PART NO. PART DESCRIPTION JGGN27 JGGB27 JGGR27 10909-T60 CASTING BOTTOM 10473-T60 CASTING TOP 164D4387 NAMEPLATE 164D4587 NAMEPLATE LOGO 10958-K70GE TOP CASTING INSERT 10571-6 HEAT INDICATOR 10240-15 HINGE PIN S21237 HINGE PIN SPACER S21233 HINGE PIN CLIP 10222-T625 FLAV-R-WAVE®...
Page 14
STAINLESS STEEL SCREW - 10-24 x 3/8 117. 10393-K50 SHELF – SIDE BURNER 118. 10393-T221 SHIELD – SIDE BURNER 121. 10184-K613 CASTOR SUPPORT 123. S15115 GREASE PAN – DISPOSABLE To obtain replacement parts, call during normal business hours: 866.GE.GRILL (866.434.7455).