Emerson CPC ISIS Installation And Configuration Manual
  1. Manuals
  2. Brands
  3. Emerson Manuals
  4. Server
  5. CPC ISIS
  6. Installation and configuration manual
Emerson CPC ISIS Installation And Configuration Manual

Emerson CPC ISIS Installation And Configuration Manual

In-store information server
Hide thumbs
Table of Contents

Quick Links

026-1306 Rev 0 12-04-02
In-Store Information Server (ISIS) Installa-
tion and Configuration Guide
Table of Contents
loading

Related Manuals for Emerson CPC ISIS

Summary of Contents for Emerson CPC ISIS

  • Page 1 026-1306 Rev 0 12-04-02 In-Store Information Server (ISIS) Installa- tion and Configuration Guide...
  • Page 3 1640 Airport Road, Suite 104 Kennesaw, GA 31044 Phone: 770-425-2724 Fax: 770-425-9319 ALL RIGHTS RESERVED. The information contained in this manual has been carefully checked and is believed to be accurate. However, Com- puter Process Controls, Inc. assumes no responsibility for any inaccuracies that may be contained herein. In no event will Computer Process Controls, Inc.

  • Page 5: Table Of Contents

    Table of Contents 1 IN-STORE INFORMATION SERVER (ISIS) INSTALLATION INSTRUCTIONS ..........1 1.1. O ..................................1 VERVIEW 1.2. A NT ..............................1 BOUT INDOWS 1.3. P ................................1 RECAUTIONS 1.3.1. Safety Precautions..............................1 1.3.2. Static Discharge Precautions..........................1 1.3.3. General Precautions ............................. 2 1.4.

  • Page 7: In-Store Information Server (Isis) Installation Instructions

    In-Store Information 1.2. About Windows NT Server (ISIS) Installa- tion Instructions The base operating system installed on the ISIS is the ® embedded version of Windows NT . This version is unique in that it does not support a traditional desktop environment including keyboard and monitor.

  • Page 8: General Precautions

    known, securely grounded object. Table 1-1 ISIS Compatibility • Do not handle the printed circuit board without Controller Supported Y/N proper protection against static discharge. Use a wrist strap when handling PCBs. The wrist strap BCU version 2.20 and clamp must be secured to earth ground. higher 1.3.3.

  • Page 9: Mounting

    Location for Mounting of the cabinet and the connectors will be situated to- wards the top of the cabinet. • This product is intended for indoor use only. The unit should not be exposed to ambient conditions outside of the range of 0ºC (32 degrees F) to 35ºC 1.8.

  • Page 10: Power Up And Initial Checkout

    1.11.1.Ethernet on the back of the ISIS and the standard AC power connector to a dedicated 120VAC or (240VAC) duplex outlet. See Section 1.8., Connection is made via a standard male RJ-45 (8- Power Requirements. Other connections are wire) connector. Using a Category 5 unshielded twisted not needed at this time.

  • Page 11: Figures

    1.12. Figures 1.12.1.ISIS Connector Layout 6-3/4 in 172 mm COM1 RS-232 COM1 COM2 RS-232 COM2 LINE 6-9/16 in 6-13/16 in 167 mm 173 mm Printer LPT1 PHONE Power Connector HDD LED POWER LED Power Switch 7-7/8 in 200 mm (optional) Modem Ethernet Line RJ-11...

  • Page 12: Mounting Detail

    1.12.2.Mounting Detail Figure 1-3 - ISIS (top view) RS-485 Option 1.13. RS-485 Option Table 1-3 - COM Port Assignments for RS-485 Ports on an ISIS RS-485 Option An ISIS ordered with the NP-485 option has a fac- tory-installed RS-485 adapter, located in slot 2 (Figure 1- RS-485 Adapter COM Port Assignments 2).

  • Page 13: Wiring Details

    1.14. Wiring Details Each connector supports both full and half-duplex for RS-485 signals on the DB-9 connectors are given in this table: Table 1-4 - Pinouts for RS-485 ports on an ISIS RS-485 option (model NP-485). NP-485 option DB-9 Connector, RS-485 Pinouts Name Description DP-9P (male) connector...

  • Page 14: Maintenance

    1.16. Maintenance 1.17. Replacement Parts Use the following procedures to perform simple Servicing the ISIS may call for replacement parts. maintenance tasks on the ISIS controller. There are three categories of parts: 1.16.1.Filter Maintenance • Non-replaceable • Standard Replacement Following the construction phase, and then on a quar- •...

  • Page 15: Standard Replacement Parts

    If you suspect this product is causing interference, turn your computer on and off while the radio or TV is 1.19. Standard Replacement showing interference. If the interference disappears when Parts you turn the computer off and reappears when you turn the computer on, something in the computer is causing the Standard replacement parts are listed in Table 1-5 on interference.

  • Page 16: Einstein Connection

    1.20.3.Einstein Connection Figure 1-6 - ISIS to Einstein Refer to Figure 1-2 for a closer look at connectors and LEDs for the ISIS. To connect an Einstein controller to the ISIS, use an Ethernet connection: Plug one end of the Category 5 unshielded twisted pair (UTP) Ethernet cable into the RJ- 45 connector on the ISIS.

  • Page 17: Reflecs Connection

    1.20.4.REFLECS Connection Figure 1-7 - ISIS to REFLECS Refer to Figure 1-2 for a closer look at connectors and LEDs for the ISIS. To connect a REFLECS controller to the ISIS, follow these steps: Take the supplied CPC-approved network ca- ble and plug the 9-pin connector into RS-232 COM 1.

Table of Contents