Table of Contents
Quick Links
Pole Hedge Trimmer
Model CH 22EPA(S)/CH 22EPA(SM)
CH 27EPA(S)
Handling instructions
Note:
Before using this machine, carefully read through these HANDLING INSTRUCTIONS to ensure
effi cient, safe operation. It is recommended that these INSTRUCTIONS be kept readily available as
an important reference when using this machine.
Table of Contents
Related Manuals for Hitachi CH22EPA
Summary of Contents for Hitachi CH22EPA
- Page 1 Pole Hedge Trimmer Model CH 22EPA(S)/CH 22EPA(SM) CH 27EPA(S) Handling instructions Note: Before using this machine, carefully read through these HANDLING INSTRUCTIONS to ensure effi cient, safe operation. It is recommended that these INSTRUCTIONS be kept readily available as an important reference when using this machine.
-
Page 2: Meanings Of Symbols
MEANINGS OF SYMBOLS NOTE: Some units do not carry them. Symbols WARNING The following show symbols used for the machine. Be sure that you understand their meaning before use. It is important that you read, fully Keep all people, bystanders and helpers understand and observe the following 15 m away from the unit. -
Page 3: 7. Priming Pump
WHAT IS WHAT Since this manual covers several models, there may be some diff erence between pictures and your unit. Use the instructions that apply to your unit. Fuel cap 2. Throttle trigger 3. Starter handle 4. Cutting attachment 5. Drive shaft tube 6. -
Page 4: Warnings And Safety Instructions
○ Inspect the entire unit / machine before each use. Replace ○ Keep others away when making carburetor adjustments. damaged parts. Check for fuel leaks and make sure all fasteners ○ Use only genuine Hitachi replacement parts as recommended are in place and securely tightened. by the manufacturer. -
Page 5: Specifications
SPECIFICATIONS Model CH22EPA (S) CH22EPA (SM) CH27EPA (S) Engine Displacement (cm 21.1 21.1 26.9 Spark plug NGK BMR7A NGK BMR7A NGK BMR7A Idling speed (min 3000 3000 3000 Recommended max. speed (min 10000 10000 10000 Max. engine output (kW) 0.63 0.63... -
Page 6: Operating Procedures
○ Always use branded 89 octane unleaded gasoline. ○ Use genuine two-cycle oil or use a mix between 25:1 to 50:1, please consult the oil bottle for the ratio or Hitachi Authorized Service Centers. ○ If genuine oil is not available, use an anti-oxidant added quality Fig. - Page 7 Starting 5. Then allow the engine about 2 – 3 minutes to warm up before subjecting it to any load. CAUTION Before starting, make sure the cutting attachment does not Stopping (Fig. 13) touch anything. Decrease engine speed and run at an idle for a few minutes, then turn off...
-
Page 8: Maintenance
(20) instead. If the cutting attachment still rotates after idle speed adjustment, Stop the engine. contact Hitachi Authorized Service Centers. 2. Loosen handle knob (21) slightly so that the support handle (20) slides. 3. Adjust the blade angle to desired position by holding the support handle (20). -
Page 9: Cutting Blade
Those bolts are tightened with a clearance so that the blades can move smoothly. Maintenance schedule Below you will fi nd some general maintenance instructions. For further information please contact Hitachi Authorized Service Centers. Daily maintenance ○ Clean the exterior of the unit. - Page 10 ○ Clean the cooling fi ns on the cylinder. ○ Clean the fan and the space around it. ○ Clean the muffl er of carbon. CAUTION Cleaning of cylinder fi ns, fan and muffl er shall be done by a Hitachi Authorized Service Center.
- Page 16 Shinagawa Intercity Tower A, 15-1, Konan 2-chome, Minato-ku, Tokyo, Japan Code No. E99249313 NS Printed in Japan...