Summary of Contents for Healthrider SoftStrider DRTL25060
Page 1
Model No. DRTL25060 Serial No. Serial Number Decal QUESTIONS? As a manufacturer, we are committed to providing complete customer satisfaction. If you have questions, or find that there are missing or dam- aged parts, we will guarantee complete satisfaction through direct assistance from our factory.
Page 3
35 or persons with pre-existing health problems. Read all instructions before using. HealthRider assumes no responsibility for personal injury or prop- erty damage sustained by or through the use of this product.
To help us assist you, please note the product model number and serial number before calling. The model number is DRTL25060. The serial number can be found on a decal attached to the tread- mill (see the front cover of this manual for the location).
ASSEMBLY Assembly requires two people. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Assembly requires only a phillips screwdriver and wire cutters 1. Using wire cutters, cut the cable tie from each upright.
Page 6
18. Make sure that all parts are tightened before you use the treadmill. The use of all remaining parts will be explained in later sections of this manual. Note: Place a mat beneath the treadmill to protect the floor or carpet.
GROUNDING INSTRUCTIONS THE PERFORMANT LUBE WALKING BELT Your treadmill features a walking belt coated with PERFORMANT LUBE , a high-performance lubricant. IMPORTANT: Never apply silicone spray or other substances to the walking belt or the walking plat- form. They will deteriorate the walking belt and cause excessive wear.
When the console is in the manual mode, the speed and incline of the treadmill can be changed with a touch of a button. As you exercise, large LED displays will provide continuous exercise feedback. The con- sole even includes a built-in telephone that allows you to answer or make calls without leaving the treadmill.
Page 9
Refer to the drawing at the top of page 8. A. Telephone—The built-in telephone allows you to answer or make telephone calls without leaving the treadmill. The telephone can also be used to call E-Coach ® for a Personal Trainer program.
Page 10
After the INCLINE buttons are pressed, it may take a few seconds for the treadmill to reach the selected incline setting. Any time that the INCLINE buttons are pressed, the DISTANCE/INCLINE display will show the incline setting for seven seconds.
Page 11
THE SPEED PROGRAMS The Incline program automatically controls the incline of the treadmill as it guides you through an effective work- out. The Speed 1, Speed 2, and Speed 3 programs au- tomatically control the speed of the treadmill. The pro- gram profiles printed on the console show how the in- cline or speed will change during each program.
Page 12
SPEED buttons. If you selected the Speed 1, Speed 2, or Speed 3 program, the incline of the treadmill can be changed with the INCLINE buttons. The program will continue until the setting of the last segment is shown in the CURRENT SEGMENT col- umn and no time remains in the TIME display.
Page 13
The programs control both the speed and incline of the treadmill. Insert the key fully into the console. See HOW TO TURN ON THE POWER on page 9.
Page 14
CUR- RENT SEGMENT column, and the speed of the button repeatedly until the treadmill will change accordingly. The incline will also change according to the settings that you pro- grammed previously.
Page 15
THE USER INFORMATION MODE The console features a user information mode that keeps track of the total time and distance accumulated on the treadmill. The information mode also allows you to switch the console from miles per hour to kilometers per hour.
1. Hold the handrails. Place one foot on the base as shown. 2. Tilt the treadmill back until it rolls freely on the front wheels. Carefully move the treadmill to the desired location. Never move the treadmill without tipping it back, or the base pads may come off.
2. SYMPTOM: THE POWER TURNS OFF DURING USE a. Check the circuit breaker located on the treadmill frame near the power cord (see 1. c. above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.
If this occurs, remove the key, wait for ten seconds, and then reinsert it. If you weight over 200 pounds, it may also be helpful to increase the incline of the treadmill. If the error code appears again, call our Customer Service Department.
Page 19
TRAINING ZONE (Beats/Min.) Unconditioned 138-167 136-166 135-164 134-162 132-161 131-159 129-156 127-155 126-153 125-151 123-150 122-147 120-146 To measure your heart rate, stop exer- cising and place two fingers on your wrist as shown. Take a six-second heartbeat count, and multiply the result by ten to find your heart rate.
Page 20
REMOVE THIS PART LIST/EXPLODED REMOVE THIS EXPLODED DRAWING DRAWING FROM THE MANUAL! AND PART LIST FROM THE MANUAL Save this EXPLODED DRAWING and PART LIST for future reference. Note: Specifications are subject to change without notice. For information about ordering replacement parts, see the back cover of the User’s Manual.
Page 21
PART LIST—Model No. DRTL25060 Key No. Qty. Description Left Link Arm Right Link Arm Incline Motor Bolt Motor Tension Washer Motor Tension Star Washer Motor Tension Nut Pulley Cover Screw Left Pivot Bolt Link Arm Bolts Spacer Upright Bolt Console Screw/Latch Screw...
HealthRider’s option, the product at one of its authorized service centers. All products for which warranty claim is made must be received by HealthRider at one of its au- thorized service centers with all freight and other transportation charges prepaid, accompanied by suffi- cient proof of purchase.