Table of Contents
Table of Contents
Related Manuals for Electrolux R410A
Summary of Contents for Electrolux R410A
- Page 1 INVERTER SPLIT - TYPE (R410A)
- Page 2 Installation work must be performed in accordance with the national wiring standards by authorised personnel only. Wrong connection can cause over heating or fire. Take care not to catch fingers on the fan when adjusting vertical louvres. This air conditioner uses R410A refrigerant.
- Page 3 Do not use the socket if it is Do not open the unit loose or damaged. during operation. It may cause fire. It may cause fire and electric It may cause an explosion or fire. shock.
- Page 4 Sharp edges could cause injury. There is danger of fire or electric shock.
- Page 5 Mode Cooling operation Drying operation Heating operation Temperature Room temperature 10 C 32 C 17 C 32 C 17 C 27 C Outdoor temperature 18 C 50 C -15 C 34 C 10 C 50 C CAUTION: 1. If air conditioner is used outside of the above conditions, certain safety protection features may come into operation and cause the unit to function abnormally.
-
Page 7: Features Of Remote Control
AUTO, COOL, DRY, HEAT to Timer on button Press the TIMER ON button to TIMER ON set the auto-on time sequence. To cancel the auto-on time TIMER OFF sequence press the TIMER ON button until the auto-on time is set to "0:00"... - Page 8 AUTO, COOL, DRY, HEAT and FAN only (Refer to note below) and back to AUTO.
-
Page 9: Using Remote Control
When you set the air conditioner in AUTO mode, it will automatically select cooling, heating or fan only operation depending on what temperature you have selected and the room temperature. TIMER ON TIMER OFF TURBO DIRECTION... - Page 10 Press to select COOL, HEAT or FAN only. TIMER ON TIMER OFF TURBO DIRECTION TIMER ON TIMER OFF TURBO DIRECTION...
- Page 11 1. TIMER ON button Press this button to initiate the TIMER ON sequence. Each press will increase the TIMER ON setting in 30 minutes increments. When the setting time displays 10:00, each press will increase the TIMER ON setting in 60 minutes increments. To cancel the TIMER ON program, simply adjust the TIMER ON time to "0:00".
- Page 12 To stop the air conditioner 2 hours after setting and start it again 10 hours after setting. 1. Press the TIMER ON button until you can see 10h on the TIMER ON display. 2. Press the TIMER OFF button until you can see 2.0h on the TIMER OFF display.
- Page 13 TIMER ON TIMER OFF TIMER OFF TURBO TURBO DIRECTION DIRECTION TIMER OFF TURBO DIRECTION left hand...
- Page 14 ADJUSTING AIR FLOW DIRECTION Adjust the air flow direction properly otherwise, it might cause discomfort or cause uneven room temperatures. Adjust the horizontal louvre using the remote controller. Adjust the vertical louvre manually. Adjusting the Vertical Air Flow Direction (up - down) The air conditioner automatically adjusts the vertical air flow direction in accordance with the operating mode.
-
Page 15: Indoor Unit
PARTS IDENTIFICATION Indoor unit 1. Front panel Indoor unit 2. Air inlet 3. Air filter 4. Air outlet Horizontal air flow grille Vertical air flow louvre 7. Display panel 8. Remote controller signal receiver 9. Remote controller 10. Manual control button Outdoor unit 11. - Page 16 Manual operation Manul operation can be used temporarily in case you can find the remote controller or its batteries are exhausted. Open and lift the front panel up to an angle until it remains fixed with a clicking sound. One press of the manual control button will lead to the forced AUTO operation.
- Page 17 Cleaning and maintenance WARNING It is necessary to stop the air conditioner and Household Drain disconnect the power supply before cleaning. Cleaner Cleaning the indoor unit and remote controller CAUTIONS Use a dry cloth to wipe the indoor unit and remote controller.
- Page 19 HOW THE AIR CONDITIONER WORKS AUTOMATIC OPERATION Press ECONOMY button When you set the air conditioner in AUTO mode, it will automatically select cooling, heating, or fan only operation depending on what temperature Temperature you have selected and the room temperature. 1 hour 1 hour Cooling...
- Page 20 Operation tips The following events may occur during normal operation. Protection of the air conditioner. Compressor protection The compressor can't restart for 3 minutes after it stops. Anti-cold air The unit is designed not to blow cold air on HEAT mode, when the indoor heat exchanger is in one of the following three situations and the set temperature has not been reached.
- Page 21 Dust is blown out from the indoor unit. This is a normal condition when the air conditioner has not been used for a long time or during first use of the unit. A peculiar smell comes out from the indoor unit. This is caused by the indoor unit giving off smells permeated from building material, from furniture, or smoke.
- Page 22 Troubleshooting tips Malfunctions and Solutions Stop the air conditioner immediately if one of the following faults occur. Disconnect the power and contact the nearest customer service center. If the following code appears on the LED window, disconnect the power and contact the service people: E0,E1,E2,E3,E4,E5,E6,E7,E8 or P0,P1,P2,P3,P4.