Table of Contents
SERVICE MANUAL
Ver. 1.1 2005.05
AUDIO POWER SPECIFICATIONS
(US model only)
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION
With 3.2-ohm loads, both channels driven
from 100 - 10,000 Hz; rated 1.5 W per
channel-minimum RMS power, with no
more than 10 % total harmonic distortion
in AC operation.
CD player section
System
Compact disc digital audio system
Laser diode properties
Emission duration: Continuous
Laser output: Less than 44.6 µW
(This output is the value measured at a distance
of about 200 mm from the objective lens surface
on the optical pick-up block with 7 mm
aperture.)
Spindle speed
200 r/min (rpm) to 500 r/min (rpm)
(CLV)
Number of channels
2
Frequency response
20 - 20 000 Hz +1/–2 dB
Wow and flutter
Below measurable limit
Radio section
Frequency range
CFD-E100L
FM
87.5 - 108 MHz
MW
531 - 1 611 kHz (9 kHz step)
530 - 1 610 kHz (10 kHz step)
LW
153 - 279 kHz
CFD-E100
FM
87.5 - 108 MHz
AM
531 - 1 611 kHz (9 kHz step)
530 - 1 610 kHz (10 kHz step)
Sony Corporation
9-879-702-02
Personal Audio Group
2005E05-1
Published by Sony Engineering Corporation
© 2005.05
CFD-E100/E100L
Photo : CFD-E100
CD
Section
TAPE
Section
SPECIFICATIONS
IF
FM: 10.7 MHz
AM/MW/LW: 450 kHz
Aerials
FM: Telescopic aerials
AM/MW/LW: Built-in ferrite bar aerials
Cassette-corder section
Recording system
4-track 2 channel stereo
Fast winding time
Approx. 120 s (sec.) with Sony cassette C-60
Frequency response
TYPE I (normal): 80 - 13 000 Hz
General
Speaker
Full range: 8 cm dia., 3.2 Ω, cone type (2)
Outputs
Headphones jack (stereo minijack)
For 16 - 68 Ω impedance headphones
Maximum Power output
3.6 W
Power requirements
For CD radio cassette-corder:
US, Canadian, Taiwan models:
120 V AC, 60Hz
Korean
model: 220 V AC, 60Hz
Other models: 230 V AC, 50Hz
9 V DC, 6 R14 (size C) batteries
For remote control:
3 V DC, 2 R03 (size AAA) batteries
Power consumption
AC 14 W
Canadian Model
Model Name Using Similar Mechanism
Optical Pick-up Block Name
Model Name Using Similar Mechanism
Tape Transport Mechanism Type
Battery life
For CD radio cassette-corder:
FM recording
Sony R14P: approx. 13.5 h
Sony alkaline LR14: approx. 20 h
Tape playback
Sony R14P: approx. 7.5 h
Sony alkaline LR14: approx. 15 h
CD playback
Sony R14P: approx. 2.5 h
Sony alkaline LR14: approx. 7 h
Dimensions
Approx. 385 × 190.5 × 170 mm (w/h/d)
(incl. projecting parts)
Mass
Approx. 3.1 kg (incl. batteries)
Supplied accessory
Mains lead (1)
Remote control (1)
Design and specifications are subject to change
without notice.
CD RADIO CASSETTE-CORDER
US Model
E Model
CFD-E100
AEP Model
UK Model
CFD-E100L
NEW
KSM-900AAA
NEW
MF-E100
Table of Contents
Related Manuals for Sony CFD-E100WHITE
Summary of Contents for Sony CFD-E100WHITE
-
Page 1: Specifications
4-track 2 channel stereo CD player section CD playback Fast winding time System Approx. 120 s (sec.) with Sony cassette C-60 Sony R14P: approx. 2.5 h Compact disc digital audio system Frequency response Sony alkaline LR14: approx. 7 h Laser diode properties... - Page 2 • Do not touch the soldering iron on the same conductor of the FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT circuit board (within 3 times). DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS •...
-
Page 3: Table Of Contents
CFD-E100/E100L TABLE OF CONTENTS SERVICING NOTES ..........4 GENERAL ..............6 DISASSEMBLY 3-1. Disassembly Flow ............7 3-2. Cover (Handle) ..............8 3-3. Handle Block ..............8 3-4. Cabinet (Rear) Block ............9 3-5. CD Tray Block ..............10 3-6. Optical Pick-up Block ............. 10 3-7. -
Page 4: Servicing Notes
CFD-E100/E100L SECTION 1 SERVICING NOTES NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts. - Page 5 CFD-E100/E100L Ver. 1.1 [MODEL IDENTIFICATION] The CFD-E100/E100L are available with three types and four different color variations. How to identify the destination, type, and color variation is shown below. – CD LID Top View – CD RADIO CASSETTE-CORDER CD RADIO CASSETTE-CORDER CD RADIO CASSETTE-CORDER CD RADIO CASSETTE-CORDER CD RADIO CASSETTE-CORDER...
-
Page 6: General
CFD-E100/E100L SECTION 2 This section is extracted from instruction manual. GENERAL Location of controls Loading a CD With the labeled side up Inserting a cassette Remote Control With the side you want to play facing out OPERATE (POWER) FUNCTION BAND PRESET +, –... -
Page 7: Disassembly
CFD-E100/E100L SECTION 3 DISASSEMBLY This set can be disassembled in the order shown below. 3-1. DISASSEMBLY FLOW 3-2. COVER (HANDLE) (Page 8) 3-3. HANDLE BLOCK (Page 8) 3-4. CABINET (REAR) BLOCK (Page 9) 3-5. CD TRAY BLOCK 3-9. MD BLOCK 3-8. -
Page 8: Cover (Handle)
CFD-E100/E100L Note: Follow the disassembly procedure in the numerical order given. 3-2. COVER (HANDLE) 3 cover (handle) 2 two claws 1 claw 3 cover (handle) 3-3. HANDLE BLOCK 0 handle block 2 two screws (B2.6) 1 two screws 4 four screws (B2.6) (B2.6) 8 two claws 7 screw... -
Page 9: Cabinet (Rear) Block
CFD-E100/E100L 3-4. CABINET (REAR) BLOCK 5 two caps (rear) 9 Open the cassette lid. 6 two screws (B2.6) 1 battery case lid 0 two screws (B2.6) 4 screw (B2.6) 8 two screws (B2.6) 2 two screws (B2.6) 3 screw (B2.6) 7 Open the CD lid. -
Page 10: Cd Tray Block
CFD-E100/E100L 3-5. CD TRAY BLOCK 2 two screws (B2.6) 1 flexible flat cable 4 plate (CD shaft) (20 core) (CN P701) 2 two screws (B2.6) 3 plate (CD shaft) 5 Open the CD lid. 6 CD tray block 3-6. OPTICAL PICK-UP BLOCK 2 four screws (B2.6) 6 optical pick-up block... -
Page 11: Optical Pick-Up (Ksm-900Aaa)
CFD-E100/E100L 3-7. OPTICAL PICK-UP (KSM-900AAA) 2 four screws 3 cover (frame CD) (B2.6) 8 two insulators 4 frame (CD) block 1 two screws (B2.6) 9 insulator 5 flexible board (CNP705) 0 optical pick-up (KSM-900AAA) 6 connector (CNP706) 7 CD relay board 3-8. -
Page 12: Md Block
CFD-E100/E100L 3-9. MD BLOCK 7 Open the cassette lid in the direction of arrow A , and remove the MD block in the direction of arrow B . 6 two screws (B2.6) 1 flexible flat cable (13 core) (CN303) 2 connector (CN311) 5 two screws (B2.6) 3 screw... -
Page 13: Power Board
CFD-E100/E100L 3-11. POWER BOARD 1 two harnesses 3 POWER board 2 four screws (B2.6) 3-12. TAPE MECHANISM DECK (MF-E100) 1 two buttons 2 four buttons 3 two screws (B2.6) 5 cassette lid block 6 tape mechanism deck (MF-E100) 4 screw (B2.6) -
Page 14: Rp Head (Hrp301)
CFD-E100/E100L 3-13. RP HEAD (HRP301) 4 four solders 6 two claws 1 screw 5 PRE board 7 RP head (HRP301) 2 hook tape mechanism deck 3-14. MOTOR SUB ASSY (CAPSTAN/REEL) (M901) 1 two solders 3 claw 2 screw 4 motor sub assy (CAPSTAN/REEL) (M901) 5 main belt 6 RF belt... -
Page 15: Tu Board
CFD-E100/E100L 3-15. TU BOARD 1 screw (B2.6) 3 flexible flat cable (11 core) (CNP1) 4 TU board... -
Page 16: Mechanical Adjustments
CFD-E100/E100L SECTION 4 SECTION 5 MECHANICAL ADJUSTMENTS ELECTRICAL ADJUSTMENTS PRECAUTION PRECAUTION 1. Clean the following parts with a denatured-alcohol-moistened 1. Setting swab : MEGABASS control : OFF record/playback head pinch roller erase head rubber belts TAPE DECK SECTION 0 dB=0.775 V capstan idlers 2. - Page 17 CFD-E100/E100L Ver. 1.1 0 dB=1 µV AM IF ADJUSTMENT TUNER SECTION Adjust for a maximum reading on level meter [AM] 450 kHz Setting: ( ): Singapore, Taiwan, Korean model Function: RADIO AM CV VOLTAGE ADJUSTMENT (CFD-E100 only) Band: AM Adjustment Part Frequency Display Reading on Digital Voltmeter HEADPHONE 1.0 ±...
- Page 18 CFD-E100/E100L Adjustment Location: – TU BOARD (Component Side) – FM CV Voltage Adjustment T2 FM IF Adjustment AM CV Voltage Adjustment (CFD-E100) LW CV Voltage Adjustment (CFD-E100L) T1 AM IF Adjustment FM Tracking Adjustment L3-1 MW Tracking Adjustment AM Tracking Adjustment (CFD-E100) LW Tracking Adjustment L3-2...
- Page 19 CFD-E100/E100L RF LEVEL CHECK CD SECTION Procedure: Perform all CD section check in the test mode. 1. Connect the oscilloscope to TP (RF) and TP (VREF) on the CD board. ENTERING THE CD TEST MODE 2. Set the CD test mode. 3.
- Page 20 CFD-E100/E100L MEMO...
-
Page 21: Diagrams
CFD-E100/E100L SECTION 6 DIAGRAMS 6-1. BLOCK DIAGRAM – SERVO Section – • R-ch is omitted due to same as L-ch. RF AMP, FOCUS/TRACKING SERVO, DIGITAL SIGNAL PROCESSOR, CLV SERVO, • SIGNAL PATH DIGITAL FILTER, D/A CONVERTER FIN2 : CD PLAY IC701 DETECTOR INTERPOLATION... -
Page 22: Block Diagram - Tuner Section
CFD-E100/E100L 6-2. BLOCK DIAGRAM – TUNER Section – FM IFT FM/AM RF AMP, MIX, OSC, FM/AM IF AMP, DET, MPX FM IF IC1 (CFD-E100) IC1 (CFD-E100L) ANT1 FM TELESCOPIC ANTENNA L-OUT TU-L-OUT RF-IN MIX-OUT IF-IN FM IF (Page 23) -OUT RF AMP MUTE BUFFER... -
Page 23: Block Diagram - Audio Section
CFD-E100/E100L 6-3. BLOCK DIAGRAM – AUDIO Section – INPUT SELECT, REC/PB PRE AMP CD-L-OUT IC301 (Page 21) VREF POWER MIC IN MUTE IC351 L.CD R-CH ELECTRICAL VOLUME MUTE L.RAD IC331 STANDBY SWITCH R-CH L-OUT L-OUT J361 L-IN MONITOR L.LO POWER BUFFER TU-L-OUT R-CH... -
Page 24: Block Diagram - Panel, Power Supply Section
CFD-E100/E100L 6-4. BLOCK DIAGRAM – PANEL, POWER SUPPLY Section – S0 – S16 LIQUID CRYSTAL DISPLAY LCD401 COM0 – COM3 REMOTE CONTROL RECEIVER REMOTE IC401 S407 – 414 KEY2 S401 – 406 3V-CHK 42 +3.3V CD +3.3V REGULATOR KEY1 Q908 REGULATOR CD-ON D801... - Page 25 CFD-E100/E100L Ver. 1.1 • Note for Printed Wiring Boards and Schematic Diagrams • Circuit Boards Location Note on Printed Wiring Board: Note on Schematic Diagram: • X : parts extracted from the component side. • All capacitors are in µF unless otherwise noted. (p: pF) •...
-
Page 26: Printed Wiring Boards - Cd Section
CFD-E100/E100L • See page 25 for Circuit Boards Location. 6-5. PRINTED WIRING BOARDS – CD Section – :Uses unleaded solder. CD RELAY BOARD CD BOARD R707 Q701 C701 JW762 C702 R728 R729 R710 R709 CNP705 JC704 R726 JW729 R732 JC703 R730 R713 JW732... -
Page 27: Schematic Diagram - Cd Section
CFD-E100/E100L 6-6. SCHEMATIC DIAGRAM – CD Section – • See page 40, 41 for IC Block Diagrams. • See page 39 for Waveforms. CNP706 M701 (SLED) S701 (LIMIT) ON:WHEN THE OPTICAL PICK-UP IS INNER POSITION M702 (SPINDLE) CNP705 C726 1000p C725 1000p C724... -
Page 28: Printed Wiring Board - Tuner Section (Cfd-E100 Only)
CFD-E100/E100L • See page 25 for Circuit Boards Location. 6-7. PRINTED WIRING BOARD – TUNER Section (CFD-E100 Only) – :Uses unleaded solder. TU BOARD AM FERRITE-ROD ANTENNA ANT1 FM TELESCOPIC ANTENNA (EXCEPT US, CND ) (ANT) JW14 (US, CND) TP (GND) JC24 TP (CV) (SHIELD CASE) -
Page 29: Schematic Diagram - Tuner Section (Cfd-E100 Only)
CFD-E100/E100L Ver. 1.1 6-8. SCHEMATIC DIAGRAM – TUNER Section (CFD-E100 Only) – • See page 41, 42 for IC Block Diagrams. • See page 39 for Waveform. AM FERRITE-ROD KV1520NT 220p AM OSC ANTENNA 100p JC24 JC12 JC11 1µH 0.01 220k (US, CND) EXCEPT... -
Page 30: Printed Wiring Board - Tuner Section (Cfd-E100L Only)
CFD-E100/E100L • See page 25 for Circuit Boards Location. 6-9. PRINTED WIRING BOARD – TUNER Section (CFD-E100L Only) – :Uses unleaded solder. TU BOARD TP (ANT) TP (GND) (CV) MAIN BOARD CN801 (Page 33) (11) 1-863-438- • Semiconductor Location Ref. No. Location B-10 CFD-E100/E100L... -
Page 31: Schematic Diagram - Tuner Section (Cfd-E100L Only)
CFD-E100/E100L 6-10. SCHEMATIC DIAGRAM – TUNER Section (CFD-E100L Only) – • See page 41, 42 for IC Block Diagrams. • See page 39 for Waveform. FERITE-ROD LW CV VOLTAGE IC B/D SWITCH TP (CV) FM CV VOLTAGE LC72137M-TLM FM/AM PLL JC22 JC24 CNP1... -
Page 32: Printed Wiring Board - Tape Section
CFD-E100/E100L 6-11. PRINTED WIRING BOARD – TAPE Section – 6-12. SCHEMATIC DIAGRAM – TAPE Section – • See page 25 for Circuit Boards Location. :Uses unleaded solder. • See page 42 for IC Block Diagram. • See page 39 for Waveform. IC301 TA2068N PRE BOARD... -
Page 33: Printed Wiring Board - Main Section
CFD-E100/E100L • See page 25 for Circuit Boards Location. 6-13. PRINTED WIRING BOARD – MAIN Section – :Uses unleaded solder. (CFD-E100) (CFD-E100L) • Semiconductor TU BOARD TU BOARD POWER BOARD POWER BOARD Location CNP1 CNP1 KH352 KH352 (Page 28) (Page 30) (Page 35) (Page 35) Ref. -
Page 34: Schematic Diagram - Main Section
CFD-E100/E100L Ver. 1.1 6-14. SCHEMATIC DIAGRAM – MAIN Section – • See page 42 for IC Block Diagram. • See page 39 for Waveforms. • See page 43 for IC Pin Function Description. R870 R872 RESET SIGNAL GENERATOR R848 R853 R854 R869 C822... -
Page 35: Printed Wiring Boards - Power Section
CFD-E100/E100L • See page 25 for Circuit Boards Location. 6-15. PRINTED WIRING BOARDS – POWER Section – :Uses unleaded solder. BATTERY 2 BOARD • Semiconductor BATTERY 1 BOARD Location DRY BATTERY Ref. No. Location SIZE "C" (IEC DESIGNATION R14) D351 6 PCS. -
Page 36: Schematic Diagram - Power Section
CFD-E100/E100L 6-16. SCHEMATIC DIAGRAM – POWER Section – • See page 42 for IC Block Diagram. DRY BATTERY POWER AMP SIZE"C" IC351 BA5417 (IEC DESIGNATION R14) 6PCS. 9V CN363 KH361 SP L IN L C252 R252 R261 CN362 IN R C253 KH351 C155... -
Page 37: Printed Wiring Boards - Lcd Section
CFD-E100/E100L • See page 25 for Circuit Boards Location. 6-17. PRINTED WIRING BOARDS – LCD Section – :Uses unleaded solder. DISPLAY MODE BOARD ENTER/MEMORY REMOTE CONTROL BOARD OPR/BATT D401 S403 MODE S404 R424 C402 R405 R423 R406 C401 IC401 (11) (11) 1-866-170- S401 –... -
Page 38: Schematic Diagram - Lcd Section
CFD-E100/E100L 6-18. SCHEMATIC DIAGRAM – LCD Section – (Page 34) (Page 34) S407 R417 LCD401 LIQUID CRYSTAL DISPLAY S412 R411 VOLUME + S408 R418 2.2k R419 R412 2.2k S413 R413 S401 VOLUME - (CFD-E100) (CFD-E100L) S409 R420 S406 BAND,RADIO POWER OPERATE 4.7k TUNE -... - Page 39 CFD-E100/E100L Waveforms – CD Board – – TU Board – – MAIN Board – IC701 4 (RF) IC2 w; (XOUT) IC801 ua (XT2) (CD play mode) 3.3 Vp-p 0.9 Vp-p 1.3 Vp-p 30.6 s 13.3 s 500 mV/DIV, 500 ns/DIV 500 mV/DIV, 5 s/DIV 1 V/DIV, 10 s/DIV IC701 qd (FE)
- Page 40 CFD-E100/E100L IC Block Diagrams – CD Board – IC701 LC78646E-US-E 78 77 76 75 74 73 72 71 69 68 67 66 65 64 63 62 61 FIN1 – FIN2 – TIN1 TBAL – – TIN2 – – TBAL – RFMON LEVEL SET MONI...
- Page 41 CFD-E100/E100L IC702 BA5826FP-E2 SP– D.BUFF SL– D.BUFF LEVEL D.BUFF SHIFT D.BUFF SPIN LEVEL SHIFT SLIN THERMAL SHUT-DOWN MONITOR (SLIN) REG–B VREF REGO MUTE (FIN) DRIVER MUTE (TIN) LEVEL LEVEL SHIFT D.BUFF SHIFT D.BUFF F– T– D.BUFF D.BUFF OPOUT OPIN – TU Board – IC1 TA2149BN RF GND FM RFOUT...
-
Page 42: Pre Board
CFD-E100/E100L IC2 LC72137M-TLM-E – MAIN Board – IC331 PT2257-S XOUT REFERENCE DIVIDER AOUT PHASE 12BITS DETECTOR ROUT PROGRAMMABLE LOUT CHARGE DIVIDER PUMP UNLOCK DETECTOR POWER ON RESET CONTROL UNIT SWALLOW COUNTER FMIN 1/16,1/17 4BITS UNIVERSAL COUNTER AMIN IFIN – PRE Board – –... - Page 43 CFD-E100/E100L Ver. 1.1 • IC Pin Function Description MAIN BOARD IC801 PD789478GC-A41-8BT-A (SYSTEM CONTROLLER) Pin No. Pin Name Description 1, 2 Not used 3 to 5 VLC2 to VLC0 Terminal for doubler circuit capacitor connection to develop liquid crystal display drive voltage 6 to 9 COM0 to COM3 Common drive signal output to the liquid crystal display...
- Page 44 CFD-E100/E100L Pin No. Pin Name Description Sub system clock output terminal (32.768 kHz) Power supply terminal (+3.3V) Ground terminal Main system clock input terminal (4.19 MHz) Main system clock output terminal (4.19 MHz) System reset signal input "L": reset For several hundreds msec. after the power supply rises, "L" is input, then it changes to "H" V-CLK Serial data transfer clock signal output to the electrical volume V-DATA...
-
Page 45: Exploded Views
CFD-E100/E100L Ver. 1.1 SECTION 7 EXPLODED VIEWS NOTE: • -XX and -X mean standardized parts, so they • Items marked “*” are not stocked since they The components identified by mark 0 or may have some difference from the original are seldom required for routine service. -
Page 46: Main Section
CFD-E100/E100L 7-2. MAIN SECTION panel (upper) section cabinet (rear) section cabinet (front) section Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-252-827-01 SCREW (B2.6), (+) BV TAPPING 2-587-576-11 LID, BATTERY CASE (for WHITE: LIV) 2-587-607-01 CAP (REAR) (for WHITE: ORIGINAL) 2-587-576-21 LID, BATTERY CASE (for SILVER) 2-587-607-11 CAP (REAR) (for WHITE: LIV) 2-587-576-31 LID, BATTERY CASE (for BLUE) -
Page 47: Cabinet (Front) Section
CFD-E100/E100L Ver. 1.1 7-3. CABINET (FRONT) SECTION SP101 supplied not supplied CD tray section not supplied SP201 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 2-587-579-01 WINDOW (CD) (for WHITE: ORIGINAL) * 109 A-4542-926-A CD BOARD, COMPLETE 2-587-579-11 WINDOW (CD) (for WHITE: LIV) 3-254-142-01 SCREW (B3), (+) BV TAPPING 2-587-579-21 WINDOW (CD) (for SILVER) -
Page 48: Panel (Upper) Section
CFD-E100/E100L Ver. 1.1 7-4. PANEL (UPPER) SECTION LCD401 D401 REMOTE CONTROL board LCD board MODE board Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-1109-063-A MODE BOARD, COMPLETE X-2059-691-1 PANEL (UPPER) SUB ASSY (for WHITE: LIV) 3-253-143-01 SCREW (B2.6), (+) P TAPPING 1-830-508-11 CABLE, FLEXIBLE FLAT (3 CORE) X-2059-694-1 PANEL (UPPER) SUB ASSY (for BLUE, SILVER) -
Page 49: Cabinet (Rear) Section
CFD-E100/E100L 7-5. CABINET (REAR) SECTION ANT1 main board section Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-252-827-01 SCREW (B2.6), (+) BV TAPPING 3-918-696-11 SCREW (M3X6 LOCK ACE) 2-587-619-01 TERMINAL (+/–) (B), BATTERY * 210 1-866-167-11 BATTERY 1 BOARD 3-252-828-01 SCREW (B2.6), (+) PWH TAPPING 2-587-618-01 TERMINAL (+/–) (A), BATTERY 3-229-975-01 SPRING BATTERY (–) -
Page 50: Main Board Section
CFD-E100/E100L Ver. 1.1 7-6. MAIN BOARD SECTION supplied MD block section-1 not supplied F901 T901 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-254-151-01 SCREW (B2.6), (+) P TAPPING 2-587-569-31 CABINET (REAR) (for BLUE) 2-587-603-01 HOLDER (PWB) A-1109-054-A POWER BOARD, COMPLETE (US) 1-829-241-11 CABLE, FLEXIBLE FLAT (11 CORE) A-1109-052-A MAIN BOARD, COMPLETE (US, CND) -
Page 51: Cd Tray Section (Ksm-900Aaa)
CFD-E100/E100L 7-7. CD TRAY SECTION (KSM-900AAA) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 2-587-594-01 TRAY, CD (for WHITE: ORIGINAL) 2-587-593-01 COVER (FRAME CD) 2-587-594-11 TRAY, CD (for WHITE: LIV) 2-587-594-21 TRAY, CD (for SILVER) 1-830-506-11 CABLE, FLEXIBLE FLAT (20 CORE) 2-587-594-31 TRAY, CD (for BLUE) 3-253-143-01 SCREW (B2.6), (+) P TAPPING 3-265-479-01 CUSHION (OP) -
Page 52: Md Block Section-1
CFD-E100/E100L 7-8. MD BLOCK SECTION-1 MD block section-2 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 2-587-584-01 BUTTON (MD REC) (z) (for WHITE: ORIGINAL) 2-587-581-11 BUTTON (MD FWD) (M) (for WHITE: LIV) 2-587-584-11 BUTTON (MD REC) (z) (for WHITE: LIV) 2-587-581-21 BUTTON (MD FWD) (M) (for SILVER, BLUE) 2-587-584-21 BUTTON (MD REC) (z) (for SILVER, BLUE) 2-587-586-01 BUTTON (MD STOP) (xZ) -
Page 53: Md Block Section-2
CFD-E100/E100L 7-9. MD BLOCK SECTION-2 tape mechanism deck section Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-3683-864-A PRE BOARD, COMPLETE 2-587-596-01 HOLDER (MD) (for WHITE: ORIGINAL) 3-252-614-01 CHASSIS, TC 2-587-596-11 HOLDER (MD) (for WHITE: LIV) 2-587-597-01 HOLDER (CASSETTE) 2-587-596-21 HOLDER (MD) (for SILVER) X-2055-196-1 LID SUB ASSY, CASSETTE... -
Page 54: Tape Mechanism Deck Section (Mf-E100)
CFD-E100/E100L 7-10. TAPE MECHANISM DECK SECTION (MF-E100) M901 not supplied HRP301 S902 not supplied HE301 supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-1119-419-A MECHANISM DECK ASSY (MF-E100) HRP301 3-266-053-01 HEAD, RP (RECORD/PLAYBACK) 3-933-825-01 ARM ASSY, PINCH ROLLER M901 X-3385-048-1 MOTOR SUB ASSY (CAPSTAN/REEL) 3-266-054-01 BELT, MAIN... -
Page 55: Electrical Parts List
CFD-E100/E100L Ver. 1.1 SECTION 8 BATTERY 1 BATTERY 2 ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • RESISTORS When indicating parts by reference number, parts list may be different from the parts All resistors are in ohms. please include the board name. - Page 56 CFD-E100/E100L CD RELAY HEADPHONE HEADPHONE TRANSLATION Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R712 1-216-809-11 METAL CHIP 1/10W R261 1-216-809-11 METAL CHIP 1/10W ************************************************************ R713 1-216-809-11 METAL CHIP 1/10W R714 1-216-853-11 METAL CHIP 470K 1/10W 1-866-166-11 HEADPHONE TRANSLATION BOARD R715 1-216-849-11 METAL CHIP...
- Page 57 CFD-E100/E100L Ver. 1.1 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-1109-052-A MAIN BOARD, COMPLETE (US, CND) C932 1-126-382-11 ELECT 100uF A-1119-536-A MAIN BOARD, COMPLETE (TW, KR) C933 1-164-156-11 CERAMIC CHIP 0.1uF A-1126-046-A MAIN BOARD, COMPLETE (AEP, UK, IT, EE, RU) C934 1-164-156-11 CERAMIC CHIP 0.1uF...
- Page 58 CFD-E100/E100L Ver. 1.1 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark Q908 8-729-036-86 TRANSISTOR KTC3203Y-AT R835 1-216-821-11 METAL CHIP 1/10W < RESISTOR > R836 1-216-853-11 METAL CHIP 470K 1/10W R837 1-216-845-11 METAL CHIP 100K 1/10W R131 1-216-817-11 METAL CHIP 1/10W...
- Page 59 CFD-E100/E100L Ver. 1.1 MAIN MODE POWER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R883 1-216-864-11 SHORT CHIP 0 (US, CND, SP) A-1109-054-A POWER BOARD, COMPLETE (US) R891 1-216-833-11 METAL CHIP 1/10W A-1119-538-A POWER BOARD, COMPLETE (AEP, UK, IT, EE, RU, KR) R892 1-216-841-11 METAL CHIP...
- Page 60 CFD-E100/E100L Ver. 1.1 POWER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < IC > C107 1-162-962-11 CERAMIC CHIP 470PF C201 1-162-964-11 CERAMIC CHIP 0.001uF IC351 8-759-426-51 IC BA5417 C202 1-104-665-11 ELECT 100uF C203 1-165-176-11 CERAMIC CHIP 0.047uF <...
- Page 61 CFD-E100/E100L Ver. 1.1 REMOTE CONTROL Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R211 1-216-829-11 METAL CHIP 4.7K 1/10W 1-162-970-11 CERAMIC CHIP 0.01uF R212 1-216-827-11 METAL CHIP 3.3K 1/10W (E100L) R301 1-216-857-11 METAL CHIP 1/10W 1-162-910-11 CERAMIC CHIP 0.25PF 50V R302 1-216-829-11 METAL CHIP...
- Page 62 CFD-E100/E100L Ver. 1.1 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-162-919-11 CERAMIC CHIP 22PF 8-719-988-61 DIODE 1SS355TE-17 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 8-719-988-61 DIODE 1SS355TE-17 1-136-169-00 FILM 0.22uF (E100) < IC > 1-137-194-81 FILM 0.47uF 6-700-512-01 IC TA2149BN (E100L) 8-759-483-40 IC LC72137M-TLM-E...
- Page 63 CFD-E100/E100L Ver. 1.1 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-216-821-11 METAL CHIP 1/10W < TRANSFORMER > 1-216-833-11 METAL CHIP 1/10W (E100L) 1-433-741-11 TRANSFORMER, IF 1-216-825-11 METAL CHIP 2.2K 1/10W 1-419-465-11 COIL (DET) (E100L) 1-216-829-11 METAL CHIP 4.7K 1/10W <...
- Page 64 CFD-E100/E100L Ver. 1.1 Ref. No. Part No. Description Remark 2-596-560-31 MANUAL, INSTRUCTION (SWEDISH) (E100L: EE, RU) 2-596-560-41 MANUAL, INSTRUCTION (FINNISH) (E100L: EE, RU) 2-596-560-51 MANUAL, INSTRUCTION (POLISH) (E100L: EE, RU) 2-596-560-61 MANUAL, INSTRUCTION (CZECH) (E100L: EE, RU) 2-596-560-71 MANUAL, INSTRUCTION (HUNGARIAN) (E100L: EE, RU) 2-596-560-81 MANUAL, INSTRUCTION (SLOVAKIAN) (E100L: EE, RU)
- Page 65 CFD-E100/E100L MEMO...
- Page 66 CFD-E100/E100L REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2005.05 2005.05 Addition of Singapore and Taiwan model...