1. Manuals
  2. Brands
  3. AEG Manuals
  4. Air Compressor
  5. AC3060S
  6. Original instructions manual

AEG AC3060S Original Instructions Manual

Hide thumbs
Table of Contents

Quick Links

AC3060S
Original instructions
Table of Contents
loading

Related Manuals for AEG AC3060S

Summary of Contents for AEG AC3060S

  • Page 1 AC3060S Original instructions...
  • Page 2 Important! It is essential that you read the instructions in this manual before assembling, operating and maintaining the product. Subject to technical modifications.
  • Page 3 Fig. 1 1 - Air filter assembly x4 2 - On/off switch 3 - Tank pressure gauge 4 - Regulator pressure gauge 5 - Quick connect coupler 6 - Pressure regulator knob 7 - Pressure relief valve 8 - Front handle 9 - Rubber foot x2 10 - Drain valve 11 - Wheel x2...
  • Page 4 Fig. 6a Fig. 6b Fig. 7 Fig. 9 1 - Quick connect coupler 2 - Quick connect air fitting 3 - To close (counterclockwise) 4 - Pressure relief valve 5 - Pressure regulator locking ring Fig. 8 1 - Regulated pressure gauge 2 - Tank pressuse gauge 1 - Quick connect air fitting 3 - To open (clockwise)
  • Page 5 Fig. 10 Fig. 11 1 - Drain valve 1 - Ring 2 - To close 2 - Pressure relief valve 3 - To open Fig. 12 1 - Air filter housing 2 - Air filter 3 - Air filter cover...

  • Page 6: General Safety Warnings

    TECHNICAL DATA SILENT AIR COMPRESSOR AC3060S Rated motor power 2200 W Rated current 9.5 A Air outlets 2 pcs, 6.35mm (1/4”) NITTO style connector/ coupler (suitable for NITTO fitments) Quick connector fitting size 6.35 mm (1/4”) BSP thread Weight 73 kg...

  • Page 7: Air Compressor Safety Warnings

    AIR COMPRESSOR USE AND CARE Never point any air tool toward yourself or others. Do not operate this air compressor if it does not contain a legible Do not exceed the pressure rating of any component in the warning label. system.
  • Page 8 to completely eliminate certain residual risk factors. The following WARNING hazards may arise and the operator should pay special attention to avoid the following: Do not connect to power supply until assembly is complete. Failure to comply could result in accidental starting and possible serious Use the product only for its intended use.

  • Page 9: Operation

    OPERATION 4. Confirm that the outlet pressure is at zero (0) bar. 5. Attach hose with quick connect air fitting to 6.35 mm (1/4 in.) quick connect coupler (regulated pressure) on air compressor. DANGER Make sure to push the hose adapter end fully into the coupler until the sleeve springs forward to lock it in place.

  • Page 10: Checking The Pressure Relief Valve

    5. If drain valve is clogged, release all air pressure. Remove and clean WARNING the valve, then reinstall. Air powered tools may require more air consumption than this air compressor is capable of providing. Check the tool DANGER manual to avoid damage to the tool or risk of personal injury. Unplug the air compressor and release all air from the tank before servicing.

  • Page 11: General Maintenance

    Do not smoke while spraying or spray where spark or flame is present. Keep compressors Use only AEG accessories and spare parts. Should components need as far from the spraying area as possible. Keep to be replaced which have not been described, please contact one of compressor, at least 10 m from the spraying area and all explosive vapours.

  • Page 12: Troubleshooting

    TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION Compressor will not run Loss of power or overheating Check for proper use of extension cord No electrical power Check to be sure unit is plugged in Check fuse/breaker Blown shop/house fuse Replace shop/house blown fuse Shop/house breaker open Reset shop/house breaker, determining why problem happened...

  • Page 13: Parts List

    PARTS LIST...
  • Page 14 Description Description Description Description Motor and pump assembly 1-31 Cover Spring - Dia. 10 1-32 Cover A Washer - Dia. 10 Nut-M5 1-33 Shaft seal Washer - Dia. 45* Dia. 10*4 Left crankcase 1-34 Bearing 6908 Wheel - 10" Adjusting washer 1-35 Bolt - M8*10 Bolt - M10...

  • Page 15: Circuit Diagram

    CIRCUIT DIAGRAM Motor 2 Motor 1 Thermal protector Thermal protector 220V-240V Kelly Input power 1100W x 2 Motor Motor Main Main Pressure switch bracket bracket winding winding Aux. Aux. winding winding Power cable: 1.0 mm², 1.5 mm² Input power: 1.1 kW x 2 Capacitor Capacitor Main winding: 1.05 mm...
  • Page 16 Techtronic Industries Australia Pty Ltd 31 Gilby Road, Mount Waverley VIC, 3149, Australia Techtronic Industries N.Z. Limited Unit C, 70 Business Parade South Highbrook, Auckland 2013, New Zealand AEG is a registered trademark used under 20190326v1b license from AB Electrolux (publ).

Table of Contents