Related Manuals for Philips EasyKey 6000 Series
Summary of Contents for Philips EasyKey 6000 Series
-
Page 3: Table Of Contents
Contents 6. Other features 1. Important Information Default settings Safety Mute button Caution Disposal of used products and batteries 2. Assembly 7. Indicators Packing list Door lock status indicator Exploded views Mute indicator Notice before assembling System locking indicator Assembly procedure 3. -
Page 4: Important Information
◆ Do not hang objects on the handle in case it might affect the normal use of the lock. ◆ You can have your locks reclaimed at Philips authorized service centers. You will receive ◆ Please clean the product with soft cloth. -
Page 5: Assembly
2 Assembly Packing list This packing list is for reference only. Please refer to the actual packing items. ① Outside ② Inside escutcheon ③ Drilling template ④ Mortise escutcheon with with silicon pad silicon pad Easy Key Warranty Quick Start EasyKey Card Guide... -
Page 6: Exploded Views
Exploded views Inside escutcheon Mortise anchor Lock cylinder*1 cover*1 screw*2 Lock cylinder’s anchor battery*4 M6 screw tube*2 screw*1 Anchor screw*2 Square shaft*1 Inside escutcheon Cotter pin*1 component*1 Outside escutcheon 5. Mortise*1 component*1... -
Page 7: Notice Before Assembling
Notice before assembling Step 1 | Door swing direction This product applies to doors with four opening directions: left-hand inswing, left- hand outswing, right-hand inswing, and right-hand outswing. Left-hand swing Right-hand swing Inside Inside Left-hand Right-hand inswing inswing Outside Outside Inside Inside Left-hand... - Page 8 Adjustable rear lever instructions Loosen the screw on the Secure the screw lever and rotate the lever on the lever. 180° to the right position. Attention 1. Choose a proper installation kit base on the door thickness. The default tool kit applies to a door thickness of 30-60mm.
-
Page 9: Assembly Procedure
Assembly procedure The following assembly procedure applies to the right-hand swing doors. For left-hand swing doors, please read through the [Notice before assembling] and complete the adjustable latch instructions. To drill holes in the door Assemble the lock cylinder to according to the drilling template, the mortise, and secure the lock mount the mortise into the jamb,... - Page 10 Insert the connecting cables into the sockets accordingly, and align the square shaft with the hole. Please be sure the inside escutcheon is closely attached to the inner surface of the door, then secure the inside escutcheon with M6 anchor screws. Attention Please cut the square shaft to a proper length according to the door thickness.
-
Page 11: Get To Know Your Smart Lock
3 Get to know your smart lock This packing list is for reference only. Please refer to the actual packing items. Outside escutcheon Indicator Keypad Card reader Mute button Fingerprint sensor Front lever Mechanical key hole Reset and external power supply interface Inside escutcheon Battery compartment... -
Page 12: Settings
4 Settings Instructions before setting ◆The system mode is divided into general mode and dual-verification mode. General mode Dual-verification mode Any enrolled access methods can Any two enrolled access methods among unlock the door PIN code, key tag, and fingerprint can unlock the door Attention 1. -
Page 13: Delete A Pin Code
User settings Press [*] twice, and enter the initial master PIN code “12345678”, then press [#] to Press [*] twice, and enter the master PIN confirm. code, then press [#] to confirm. Press [2] to add a PIN code. The indicator After entering the master mode, enter will flash in green once after [2] is pressed, the new master PIN code (6-12 digits) - Page 14 Add a PIN code (optional) Place your finger on the fingerprint sensor until you hear a voice prompt, Press [*] twice, and enter the master PIN when the indicator flashes in green code, then press [#] to confirm. twice, indicating the deletion is done. Attention The fingerprint is an optional feature, if the Press [5] to add a fingerprint.
-
Page 15: Passage Mode
Attention After the passage mode is activated, press [8] for 3s can temporarily turn off the passage Press [8] to delete a key tag. The indicator mode. When the next user uses any enrolled will flash in green once after [8] is pressed, access methods to unlock the door, the indicating that the lock can perform in passage mode will be restored. -
Page 16: Get To Use Your Lock
5 Get to use your lock Outdoor unlock Fingerprint Key tag Card reader 下 Press down Fingerprint Press down 压 the handle sensor 执 the handle Place the enrolled key tag on the card Place the enrolled finger on the reader. - Page 17 Indoor unlock Handle Press down the handle to unlock Outside/Inside locking Outside locking After closing the door, lift up the handle, and the latch bolt will automatically pop up to lock the door. Inside locking After closing the door, lift up the handle, and the latch bolt will automatically pop up to lock the door.
- Page 18 Mechanical key Get the mechanical How to open the Insert the mechanical key from the product mechanical key cover: key into the lock hole, package. Lift the mechanical so that the key is 90° key cover from the vertical to the outside lip, and rotate it by 90 escutcheon.
-
Page 19: Other Features
6 Other features Default settings Function： To empty all user information and restore to default settings. How to use: Double press the [RES] button with a sharp object, and all the user information will be emptied. The lock will restore to default settings. -
Page 20: Indicators
7 Indicators Status indicator Meanings of the indicator in different colors Blue: when the system wakes up, the indicator will turn blue, indicating that the door lock can be processed and operated; 门 锁 Green: when the door lock is unlocked, the 状... -
Page 21: System Locking Indicator
System-locking indicator Flash twice Flash once The door lock will be locked for 100 seconds if there are 5 consecutive incorrect inputs among any of the 3 types of access methods (fingerprint, PIN code, or key tag) within 5 minutes. Attention 1.Only when touching to wake up the keypad or verifying the... -
Page 22: How To Apply External Power
How to apply an external power supply When the battery voltage is insufficient, and the door cannot open from outside, you can power up the lock through a 5V power bank as an external power supply via the Type-C interface. After opening the door lock, please replace the batteries immediately. - Page 23 Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license. This product has been manufactured by and is sold under the responsibility of Shenzhen Conex Intelligent Technology Co., Ltd., and Shenzhen Conex Intelligent Technology Co., Ltd. is the warrantor concerning this...