Related Manuals for Philips EasyKey 1000 Series
Summary of Contents for Philips EasyKey 1000 Series
- Page 1 Easy Key 1000 series Indoor lock DDL101-3HBS User manual ww w.philips.com/support Sign your product up and get support at ww w.philips.com/support...
-
Page 3: Table Of Contents
Contents 6. Indicators 1. Important Information Safety Caution 7. Troubleshooting Disposal of used products and batteries Low battery alert Lock-out alert 2. Assembly Battery replacement How to apply external power supply Packing list Exploded views Notice before assembling Assembly procedures 3. -
Page 4: Important Information
◆ Do not forcibly disassemble the product to Philips, a Philips authorized service center trigger an alarm or damage the product. or professional technicians. ◆ Do not scrape the fingerprint sensor with ◆... -
Page 5: Assembly
Drilling template Mortise Easy Key 1000 series Indoor lock DDL101-3HBS Easy Key User manual ww w.philips.com/support Sign your product up and get suppo rt at ww w.philips.com/support Warranty Card Lock cylinder User manual Warranty card Quality certificate cover AAA batteries... -
Page 6: Exploded Views
Exploded views 1.Interior unit x1 6.M5 screw tube x4 11.Anchor screw for lock 2.Lateral screw x4 7.Exterior unit x1 cylinder x1 3.Interior unit base x1 8.Interior lock cylinder 12.Exterior lock cylinder 4.Mortise x1 cover x1 cover x1 5.Hollow square shaft x1 9.Anchor screw x4 13.Lock cylinder x1 10.Interior lock cylinder... -
Page 7: Notice Before Assembling
Notice before assembling This product applies to doors with swing directions as follows: left-hand inswing, left-hand outswing, right-hand inswing, and right-hand outswing. Left-hand swing Right-hand swing Left-hand inswing Right-hand inswing Left-hand outswing Right-hand outswing Adjustable latch instructions Adjust the latch bolt direction based on the needs of inswing and outswing doors. Push upward Push the latch bolt down, rotate... -
Page 8: Assembly Procedures
Assembly procedures The following assembly instructions are for right-hand swing doors. For left-hand swing doors, please read and understand the 'Notice before assembling' section, and follow the 'Adjustable latch instructions' to adjust the latch bolt direction accordingly. Drill holes according to the drilling Align the hollow square shaft on the template, then place the mortise exterior unit with the rotating opening... - Page 9 Connect the cable to the interior Insert the lock cylinder and secure unit. Then assemble the interior unit it with the screw as shown in the and the interior lock cylinder cover. diagram. Use the provided screws to secure the interior unit and the interior decorative ring on both sides.
-
Page 10: Get To Know Your Lock
3 Get to know your lock This packing list is for reference only. Please refer to the actual packing items. Exterior unit Fingerprint sensor ① Type-C port ② Mechanical keyhole ③ Indicator 1 ④ Indicator 2 ⑤ Interior unit Battery cover ①... -
Page 11: Settings
4 Settings Initialization Add a master fingerprint Prerequisite: With batteries installed and the device in its default factory state. Press the setup button once. You will After inserting the batteries into hear a "beep" sound from the buzzer, the lock, perform the initialization and the blue light will stay continuously procedure and engage self-checking for lit, indicating that the device has... - Page 12 Add a user fingerprint During the first 7 presses User fingerprints can be used for daily unlocking and remain valid permanently unless the system is restored to default settings. Prerequisite: Before adding user fingerprints, you need to successfully LED flashes blue twice and emits a enroll a master fingerprint.
- Page 13 Master fingerprint verification During the first 7 presses LED flashes blue twice and emits a LED in blue and emits a long “beep” short “beep” sound sound On the 8th press Press the finger that needs to be enrolled on the fingerprint sensor for 8 times.
-
Page 14: Lock Mode
Lock mode Re-clicking the setting button will cause the green light to flash twice, and the buzzer will emit two "beep" sounds, General mode indicating that the passage mode is activated. After adding fingerprints to the lock, the lock will enter the general mode, where the door requires a fingerprint to unlock after being locked. -
Page 15: Mute Mode
Restore to default Exhibition Mode settings In the default settings, before adding any fingerprints, the lock can be unlocked with any finger. Mute mode Enable mute mode Prerequisite: Non-setting mode + Mute LED in blue and emits a long “beep” mode disabled sound emits a “beep”... -
Page 16: Application Binding
Application binding 7. After adding the lock, a new interface will prompt you to rename the newly Download paired lock. 8. Tap the "Done" button in the Please scan the QR code below or top right corner, and the app will search for "Tuya Smart"... -
Page 17: Get To Use Your Lock
5 Get to use your lock Outdoor/ indoor unlock Outdoor unlock ③ After successful fingerprint verification, the motor activates the clutch to unlock, allowing you to press down the handle and open the door(If the door is locked from the inside, please insert the key into the keyway to unlock it before verifying the fingerprint). -
Page 18: Indicators
6 Indicator explanation Blue: System wake-up Green: Verification succeeded Red: Verification failed 7 Troubleshooting Low battery alert Triggering: Upon system wake-up, the battery voltage is automatically checked. If the battery voltage is low, an alert will sound after unlocking, reminding you to replace the battery promptly. - Page 19 Lock-out alert If 5 consecutive incorrect fingerprints are entered within 5 minutes, the system will lock for 3 minutes. Status indication: Red light flashes 5 times and emits 6 "beep" sounds during each verification, with the timer restarting. Alarm release: Automatically Red light flashes 5 times and emits 6 "beep"...
- Page 20 How to apply an external power supply If the battery voltage is insufficient to unlock the door from the outside, you can use a 5V power bank as an external power supply by connecting it to the lock via the Type-C port. After unlocking the door, please replace the batteries promptly.
- Page 22 Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license. This product has been manufactured by and is sold under the responsibility of Shenzhen Conex Intelligent Technology Co., Ltd. and Shenzhen Conex...