Page 1
BELMAR 52” CEILING FAN MODELS #50193, 50194 Español p. 21 Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-877-361-3883, Monday - Thursday, 8 am - 6 pm, EST and Friday, 8 am - 5 pm, EST.
PACKAGE CONTENTS Unpack your fan and check the contents. You should have the following items: 1. Blade (5) 2. Canopy 3. Hanger Bracket 4. Canopy Cover 5. Yoke Cover 6. Downrod 7. Blade Arm (5) 8. Motor Housing 9. Light Kit 10.
SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate, or install the product. • Before you begin installing the fan, disconnect the power by removing fuses or turning off the circuit breakers. • Make sure that all electrical connections comply with local codes, ordinances, the National Electrical Code, and ANSI/NFPA 70-199.
MOUNTING OPTIONS Fig. 1 DANGER Turn off the circuit breakers and the wall switch to the fan supply line leads. Failure to disconnect the power supply prior to installation may result in serious injury or death. 1. Your fan has 3 mounting options: •...
MOUNTING BRACKET INSTALLATION 4. Loosen all mounting bracket screws. Remove the Fig. 4 two mounting bracket screws and washers from the round holes of canopy. Set aside for later use. Mounting Mounting Detach mounting bracket from canopy (Fig. 4). Bracket Bracket Screws Mounting Bracket...
STANDARD OR ANGLE MOUNTING INSTRUCTIONS 6. Partially loosen the motor housing set screws in the Fig. 6 yoke at the top of the motor housing (Fig. 6). Set Screw Fig. 7 7. Remove the downrod pin and downrod clip from the downrod (Fig.
Page 8
STANDARD OR ANGLE MOUNTING INSTRUCTIONS 9. Slide the downrod into the yoke of the motor Fig. 9 Downrod housing, align the holes, and reinstall the downrod pin and downrod clip. Then retighten the set screws (Fig. 9). Downrod Downrod Clip Set Screw 10.
Page 9
STANDARD OR ANGLE MOUNTING INSTRUCTIONS 12. Install the ball end of the downrod into the Fig. 12 mounting bracket opening. Align the slot in the ball with the tab in the mounting bracket. The rod should not rotate if installed correctly (Fig. 12). Slot Mounting Bracket...
CLOSEMOUNT INSTRUCTIONS 13. Remove the canopy cover from the bottom of the Fig. 13 canopy (Fig. 13). Helpful Hint: The downrod, hanging ball, and canopy cover are not used in this type of installation. Canopy Cover Canopy 14. Align the canopy with the closemount screw holes Fig.
WIRING CAUTION Fig. 16 Be sure outlet box is properly grounded or that a ground (green or bare) wire is present. Black (live) WARNING White (neutral) If house wires are different colors than referred to in Bare/Green (ground) the following step, stop immediately. A professional electrician is recommended to determine wiring.
CANOPY INSTALLATION 18. Lift the canopy up so the partially installed mounting Fig. 18 bracket screws are situated in the L-slots on each side of the canopy. Rotate the canopy clockwise and install the remaining mounting bracket screws and washers from Step 4 (Fig. 18). Mounting Mounting Bracket Screw...
BLADE INSTALLATION 19. Remove motor screws from underside of the motor Fig. 19 Fig. 19 and save for blade arm attachment. Discard the plastic motor blocks but keep the motor screws (Fig. 19). Motor Block Motor Screw Motor Block Motor Screw 20.
LIGHT KIT INSTALLATION 22. (Optional) To install the fan without a light kit: Fig. 22 Unscrew the hex nut located inside the switch housing cap from the threaded rod in the center of the cap to remove the light kit and wiring (Fig. 22). Switch Housing Light Kit...
LIGHT KIT INSTALLATION 25. Align holes in the switch housing cap with holes Fig. 25 in upper switch housing. Re-insert screws and washers that were previously removed. Use a Phillips screwdriver (not included) to secure all screws (Fig. 25). Screw Washer Screw Washer...
Page 16
LIGHT KIT INSTALLATION 28. Feed pull chain through the center hole in the Fig. 28 glass globe, rubber washer and nut. Lift the glass globe and rubber washer over the threaded rod. Screw the nut onto the threaded rod to temporarily hold the glass globe in place.
OPERATING INSTRUCTIONS 30. Use the fan reverse switch, located on the side Fig. 30 of the light kit, to optimize your fan for seasonal performance (Fig. 30). Using a ceiling fan will allow you to raise your thermostat in the summer and lower your thermostat in the winter without sacrificing comfort.
REPLACEMENT PARTS LIST For replacement parts, call the customer service department at 1-877-361-3883, 8 a.m. - 6 p.m., EST, Monday - Thursday, 8 a.m. - 5 p.m., EST, Friday. MODEL 50193 MODEL 50194 PIECE DESCRIPTION PART # PART # Blade Arm 50193-A 50194-A Blade...
TROUBLESHOOTING At least twice each year, lower the canopy to check the downrod assembly, and then tighten all screws on the fan. Clean the motor housing with only a soft brush or lint-free cloth to avoid scratching the finish. Clean the blades with a lint-free cloth. You may occasionally apply a light coat of furniture polish to wood blades for added protection.
1-877-361-3883 Monday - Thursday, 8 am - 6 pm, EST and Friday, 8 am - 5 pm, EST. Please have a copy of the receipt as proof of purchase. The Honeywell Trademark is used under license from Honeywell International Hong Kong China Electric Appliance Manufacture Co., Ltd.