Table of Contents
NOTE!
if only the F2 filter need to be reset, access the
function pressing the
button to go to the second filter.
For detailed information about the filters cleaning and
replacement, refer to J Machine cleaning and
maintenance.
I.3.6
Control panel lockout
Press keys
and
for more than three seconds to lock /
unlock the Control panel; the blinking message
on the display if the control panel is unlocked; the blinking
message
appears on the display if the control panel is
locked.
I.4
Using the refrigerated drawers (if
present)
Some models are equipped with one or two refrigerated
drawers.
Each drawer has its own refrigerating unit and can be switched
on, adjusted and switched off independently.
In order to use the refrigerated drawers to store food, the
extraction system must be switched on pressing
J
MACHINE CLEANING AND MAINTENANCE
WARNING
Refer to "WARNING and Safety
Information"
J.1
Ordinary maintenance
J.1.1
Care information
The following care operations have to be carried out by the
owner and/or user of the appliance.
IMPORTANT
Problems resulting from poor or lack of care as
hereinafter described will not be covered by the
warranty.
WARNING
Before carrying out any cleaning
or maintenance, disconnect the
appliance from the power supply.
J.1.2
Cleaning the appliance and accessories
Before using the appliance, clean all the internal parts and
accessories with lukewarm water and neutral soap or products
that are over 90% biodegradable (in order to reduce the
emission of pollutants into the environment), then rinse and dry
thoroughly.
CAUTION
Do not use solvent-based detergents (e.g.
trichloro-ethylene) or abrasive powders
for cleaning.
J.1.3
Care of the appliance – Daily
At the end of the day's work, proceed as follows:
button, then press the
appears
button.
DANGER
Do not store explosive substan-
ces,
such
containers with flammable pro-
pellant in this appliance.
I.4.1
Switching the refrigerated drawers ON
Press the
button to switch ON the drawer
to switch ON the drawer
.
The starting refrigeration level is always set to 1 (display shows
.
I.4.2
Drawer temperature selection
To change the refrigeration level press
increase or decrease the value; there are 5 refrigeration levels,
in sequence from 1 to 5 (the coldest level) and 5 to 1, but not in
loop (example: OFF-1-2-3-4-5-4-3-2-1).
During the change, the relative level blink on the display, and it
can be confirmed pressing
Each drawer has a temperature controller for automatic
maintaining of the temperature. The drawer cooling temper-
ature values range from 0 to +10, depending on the adjustment.
NOTE!
If the temperature inside the drawer exceeds the
setpoint, the relative compressor switch on to cool
down the drawer and the icon
shown in the display.
• Remove the trays holding the operator's equipment and the
respective supports "L" (see fig. 1).
• Disconnect the cooking modules (for cleaning according
their relevant instructions) and set the unit support table free
for cleaning.
• Switch OFF the cooling of the refrigerated drawers.
• Switch OFF the unit pressing and holding down
(see fig.1) for about two seconds.
• Disconnect the main cable plug from the power supply.
• The trays and their supports "L" can be placed in a
dishwasher to remove the grease.
IMPORTANT
Do not open the refrigerated drawers for guaran-
teeing
the
stored
reactivating the refrigerating function.
Side containers
• Empty the side containers and clean in dishwasher.
• Carefully dry and fit the containers back in place after
completing the cleaning of the unit.
Cleaning grease filters
In case of intense greasy cooking, the mash filters may require
a daily cleaning.
• Extract the grease filters "G" (see fig. 1) and clean in
dishwasher.
as
pressurised
; press it again
and
button, to
button, or waiting 5 seconds.
or
will be
button
food
preservation
until
27
Table of Contents
