Honeywell FIre-LITe ALArms MS-9600LS Manual

Addressable fire alarm control panel

Hide thumbs Also See for FIre-LITe ALArms MS-9600LS:

Wiring manual (80 pages)

Table Of Contents

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

128

129

130

131

132

133

134

135

136

137

138

139

140

141

142

143

144

145

146

147

148

149

150

151

152

153

154

155

156

157

158

159

160

161

162

163

164

165

166

167

168

169

170

171

172

173

174

175

176

177

178

179

180

181

182

183

184

185

186

187

188

189

190

191

192

193

194

195

196

197

198

199

200

201

202

203

204

205

206

207

208

page of 208

/ 208
Contents
Table of Contents

Table of Contents

Quick Links

Addressable Fire Alarm Control Panel

MS-9600LS/MS-9600LSE

MS-9600UDLS/MS-9600UDLSE

MS-9600LSC

Manual

Document 52646

2/12/2010

Rev:

P/N 52646:B2

ECN 10-098

http://manualforhoneywellthermostat.com

Table of Contents

Summary of Contents for Honeywell FIre-LITe ALArms MS-9600LS

Page 1 Addressable Fire Alarm Control Panel MS-9600LS/MS-9600LSE MS-9600UDLS/MS-9600UDLSE MS-9600LSC Manual Document 52646 2/12/2010 Rev: P/N 52646:B2 ECN 10-098 http://manualforhoneywellthermostat.com...
Page 2 Fire Alarm System Limitations While a fire alarm system may lower insurance rates, it is not a substitute for fire insurance! An automatic fire alarm system—typically made up of Heat detectors do not sense particles of combustion and smoke detectors, heat detectors, manual pull stations, audible alarm only when heat on their sensors increases at a predeter- warning devices, and a fire alarm control panel with remote mined rate or reaches a predetermined level.
Page 3 LiteSpeed™ is a trademark; and FireLite® Alarms is a registered trademark of Honeywell International Inc. Microsoft® and Windows® are registered trademarks of the Microsoft Corporation. ©Tuesday, August 14, 2012 9:31 am by Honeywell International Inc. All rights reserved. Unauthorized use of this document is strictly prohibited. MS-9600LS Series Manual — P/N 52646:B2 2/12/2010...
Page 4 •Brief description of content you think should be improved or corrected •Your suggestion for how to correct/improve documentation Send email messages to: [email protected] Please note this email address is for documentation feedback only. If you have any technical issues, please contact Technical Services.
Page 5: Table Of Contents
Table of Contents Section 1: Product Description ..................... 13 1.1: Inventory..............................13 1.2: Features and Options ...........................13 1.3: Specifications...............................15 1.3.1: Current Availability...........................17 1.4: Controls and Indicators..........................17 1.5: Circuits.................................18 1.6: Components ..............................19 1.6.1: Intelligent Addressable Detectors: Newer Series ................20 1.6.2: Intelligent Addressable Modules: Newer Series ................20 1.6.3: 300 Series Intelligent Addressable Devices ..................20 1.6.4: Addressable Device Accessories .......................20 1.7: Optional Modules ............................21...
Page 6 Table of Contents Section 3: Programming ......................61 3.1: Programming Data Entry ..........................61 3.2: User Programming ............................62 3.3: Initial Power-up............................63 3.4: Programming Screens Description ......................63 3.5: Programming and Passwords........................63 3.6: Master Programming Level .........................65 3.6.1: Autoprogram............................66 3.6.2: Point Program ............................67 Detector Programming..........................67 Module Programming...........................78 3.6.3: Zone Setup ............................95...
Page 7 Table of Contents Section 4: Operating Instructions ..................150 4.1: Panel Control Buttons..........................150 4.1.1: Acknowledge/Step...........................150 4.1.2: Alarm Silence ..........................150 4.1.3: Drill/Hold 2 Sec..........................150 4.1.4: Reset ..............................150 4.2: LED Indicators............................150 4.3: Normal Operation ............................151 4.4: Trouble Operation............................152 4.5: Alarm Operation ............................153 4.6: Supervisory Operation ..........................154 4.7: Process Monitor Operation ........................155 4.8: Hazard Condition Operation........................155...
Page 8 Table of Contents 5.4.2: Selecting and Locating Batteries .....................177 Appendix A: Software Zones....................178 A.1: Correlations ...............................178 Appendix B: Default Programming ..................186 Appendix C: NFPA Standard-Specific Requirements ............187 C.1: Central Station/Remote Station Transmitter: Connection to FACP Dry Contacts ........193 C.2: MBT-1 Municipal Box Trip - Silenceable....................194 Appendix D: FACP with Keltron ..................
Page 9 It is imperative that the installer understand the requirements of the Authority Having Jurisdiction (AHJ) and be familiar with the standards set forth by the following regulatory agencies: • Underwriters Laboratories Standards • NFPA 72 National Fire Alarm Code • CAN/ULC - S527-99 Standard for Control Units for Fire Alarm Systems Before proceeding, the installer should be familiar with the following documents.
Page 10 MS-9600LS Series Manual — P/N 52646:B2 2/12/2010...
Page 11 Peripheral Devices and Their Documents: Audio Control for ACC-25/50(ZS/T) Audio-Command-Center Doc. #51889 ANN-(R)LED ANN-I/O LED Display ANN-80 ANN-S/PG LED Driver Doc. #53032 Text Annunciator ANN-RLY Printer Driver Doc. #151416 Form-C Relay Card Doc. #52749 Doc. #151417 Doc. #53033 IPDACT ANN (EIA-485) TB6 Internet Communicator Doc.
Page 12 Notes MS-9600LS Series Manual — P/N 52646:B2 2/12/2010...
Page 13: Section 1: Product Description
Section 1: Product Description The MS-9600LS and MS-9600UDLS are compact, cost effective, intelligent addressable FACPs (Fire Alarm Control Panels) with an extensive list of powerful features. The combination of Fire•Lite’s newer series devices and legacy 300 Series devices, along with the MS-9600LS or MS- 9600UDLS FACP, offer the latest in fire protection technology.
Page 14 Product Description Features and Options • Optional module for adding a second SLC loop which meets NFPA Style 4, 6 and 7 requirements • 318 addressable device capacity for each SLC loop (159 detectors and 159 control/monitor modules) • 99 software zones •...
Page 15: Specifications
Specifications Product Description • Auto-program (learn mode) reduces installation time. Reports two devices set to the same address • Password and key-protected nonvolatile memory • User programmable password • Fully programmable from local keypad or keyboard or local PC • Compatible with Fire•Lite’s newer series addressable devices (LiteSpeed and CLIP Mode) - Refer to SLC Wiring Manual for listing of all compatible addressable devices •...
Page 16 Product Description Specifications Maximum signaling current per circuit: 3.00 amps (see Figure 1.1 on page 17) End-of-Line Resistor: 4.7 k, ½ watt (P/N 71252 UL listed) for NACs Refer to Device Compatibility Document for listed compatible devices Two Programmable and One Fixed Output Relay - TB1 & TB5 Contact rating: 2.0 amps @ 30 VDC (resistive), 0.5 amps @ 30 VAC (resistive) Form-C relays Refer to Figure 2.5 on page 47 for information on power-limited wiring for relay circuits...
Page 17: 1: Current Availability
Refer to the battery calculations section for additional information. Figure 1.1 Current Availability 1.4 Controls and Indicators LCD Display HONEYWELL The FACP uses an 80-character (4 lines X 20 LIFE SAFETY characters) high viewing angle LCD display. SYSTEM ALL NORMAL The display includes a long life LED backlight that remains illuminated.
Page 18: Circuits
Product Description Circuits • Maintenance/presignal (yellow) • Alarm Silenced signals (yellow) • Disabled (yellow) • Battery fault (yellow) • Ground fault (yellow) Key Panel Mounted on the main circuit board, the key panel includes a window for the LCD display and LED indicators as listed above.
Page 19: Components
Components Product Description NAC (Notification Appliance Circuits) Up to four NACs are provided with various programmable features: • four Style Y (Class B) NACs • two Style Z (Class A) NACs Relays One fixed and two fully programmable Form-C dry contact relays are provided. The fixed fail-safe relay monitors system trouble and the two programmable relays are factory default programmed for system alarm and system supervisory.
Page 20: 1: Intelligent Addressable Detectors: Newer Series
Product Description Components the BB-26 can be used for housing the batteries. The CHG-120F can be used for charging 26 to 120 AH batteries and the BB-55F can be used for housing the batteries. Batteries must be ordered sep- arately. 1.6.1 Intelligent Addressable Detectors: Newer Series Intelligent, addressable detectors provide information to the control panel on an SLC Signaling Line Circuit (refer to the SLC Wiring Manual for detailed information on device installation, wir-...
Page 21: Optional Modules
Optional Modules Product Description N-ELR Mounting Plate The N-ELR is a single End-of-Line resistor plate which is required for use in Canada. An ELR, which is supplied with each module and fire alarm control panel, is mounted to the ELR plate. Resistors mounted to the N-ELR plate can be used for the supervision of a monitor and control module circuit.
Page 22: 2: Dress Panel: Dp-9692
Product Description Accessories Important: Remote modification of FACP programming requires that the panel be enabled for remote download (refer to the DACT-UD2 manual). Remote interrogation of panel programming, history logs, detector status, etc., is possible without enabling the remote download option. 1.8.2 Dress Panel: DP-9692 A DP-9692 dress panel is available for the FACP (required for Canadian installations).
Page 23: 6: New Ann-Bus Annunciators/Devices
Accessories Product Description 1.8.6 New ANN-BUS Annunciators/Devices NOTE: Refer to “Canadian Application” on page 200 for specific Canadian requirements. WARNING: RISK OF ELECTRICAL SHOCK AND EQUIPMENT DAMAGE DISCONNECT ALL SOURCES OF POWER (AC AND DC) BEFORE INSTALLING OR REMOVING ANY MODULES OR WIRING. The legacy ACS annunciators may not be used if new ANN-BUS annunciators are being used due to incompatible serial communication protocols.
Page 24 Product Description Accessories capacitance is the limiting factor. These cases are marked in the chart with an asterisk (*). Maxi- mum length can never be more than 6,000 feet (1,800 m), regardless of gauge used. The formula used to generate this chart is shown in the note below. Wiring Distance: ANN-BUS Modules to FACP Total Worst Case Current 22 Gauge...
Page 25 Accessories Product Description The total worst case current is calculated as follows: ANN-80 Current Draw = 3 X 0.040 amps = 0.120 amps ANN-S/PG Current Draw = 1 X.0.040 amps = 0.040 amps ANN-I/O Current Draw = 1 X.0.200 amps = 0.200 amps Total Worst Case Current Draw = 0.360 amp...
Page 26: Ann-Bus Device Addressing
Product Description Accessories Powering ANN-BUS Devices from Auxiliary Power Supply  Figure 1.4 illustrates the powering of ANN-BUS devices from an auxiliary power supply such as the FCPS-24FS6/8, when the total ANN-BUS power requirement exceeds the capability of the FACP’s DC Power Output circuit. Cut Ground Fault Detection jumper JP1 (FACP monitors for ground faults) ANN-BUS and power wiring are supervised and power-limited...
Page 27: Remote Fire Annunciator
Accessories Product Description Address Switch 4 Switch 3 Switch 2 Switch 1 Switch 5 not valid 1 Switch 5 must be set to OFF for ANN-BUS devices to be recognized. ANN-80 Remote Fire Annunciator The ANN-80(-W) Annunciator is a compact, 80 character, backlit LCD remote fire annunciator. It mimics the display on the control panel and will annunciate device type, point alarm, trouble or supervisory condition, zone assignment plus any custom alpha labels programmed into the FACP.
Page 28 Product Description Accessories Annunciator backplate Annunciator cover with LCD display Press in latch Pull annunciator cover open Key switch shown in OFF/Locked position Figure 1.5 ANN-80 Mounting  TheANN-80 can be surface or semi-flush mounted to a single, double or 4” square electrical box. Select and remove the appropriate knockout(s), pull the necessary wires through the knockouts and mount the annunciator in or on the wall depending on the type of installation desired.
Page 29 Accessories Product Description Wiring ANN-80 to FACP  The following steps can be used as a guide to wire the annunciator. Make certain all power has been removed from the FACP prior to annunciator installation. Route wires from hole in backplate, through wiring channel and then to ANN-80 terminal block TB1.
Page 30: Ann-S/Pg Serial/Parallel Interface Installation
Product Description Accessories The following table shows the ANN-80 connections to the FACP FACP ANN-80 (TB1) Terminal GND (-) on TB3 Terminal 1 (-) Terminal PWR (+)TB3 Terminal 2 (+) Terminal ACS on TB6 Terminal 3 (A) Terminal ACS on TB6 Terminal 4 (B) Programming Following installation and wiring of the ANN-80 LCD annunciator to the FACP, the annunciator...
Page 31 Accessories Product Description Select the address and configuration options for the ANN-S/PG module as described in the Programming section of this manual (refer to “ANN-BUS Options” on page 121). Note that the Auto-configure feature allows the programmer to quickly bring all installed ANN-BUS modules online (refer to “Auto-Configure”...
Page 32: Ann-I/O Led Driver Module
Product Description Accessories Standard Exec 10.5 SI.Zero Auto LF PAPER BIN 1 12/72” BIN 2 12/72” SINGLE 12/72” PUSH TRA 12/72” PULL TRA 12/72” PAP ROLL 12/72” Table 1.2 PRN-6F Setup Options ANN-I/O LED Driver Module* The ANN-I/O is an LED driver module that can be used in a wide variety of applications, including as an interface with most customized graphic annunciators.
Page 33 Accessories Product Description Specifications  • Max. ANN-BUS Voltage: 28 VDC • Max. Current: • Alarm: 200 mA • Standby: 35 mA • Each LED: 10 mA • Operating Temperature: 32 F to 120 F (0 C to 49 • For indoor use in a dry location only ANN-I/O Connection to FACP ...
Page 34: Ann-Led Annunciator Module
Product Description Accessories Figure 1.10 ANN-I/O Board Layout ANN-LED Annunciator Module* The ANN-LED and ANN-RLED annunciator modules provide LED annunciation of general sys- tem faults and input zones/points when used with a compatible FACP. The ANN-LED module pro- vides alarm (red), trouble (yellow) and supervisory (yellow) indication for up to ten input zones or addressable points.
Page 35 Accessories Product Description *In Canada, the color red must be used to indicate active alarm inputs. Yellow indicates supervi- sory, burglary or trouble signals. Green indicates the presence of power or an activated output. Figure 1.11 ANN-LEDs (shown in possible stacked configuration) Specifications ...
Page 36: Ann-Rly Annunciator Module
Product Description Accessories ANN-LED Board Layout and Connection to FACP  Figure 1.13 illustrates the ANN-LED board showing locations of screw terminals for connection to the FACP and the DIP switches for selecting the ANN-BUS ID number. ANN-BUS (ID#) Address DIP switch 1 2 3 4 5 6 7 8 ANN-BUS ANN-LED...
Page 37 Accessories Product Description Mounting/Installation  The ANN-RLY relay module can be mounted inside the FACP main circuit board chassis or inside the ROME Series enclosure. Refer to the ANN-RLY Installation Document #53033 for instructions on chassis mounting or to the ROME Series Installation Document #53530 for mounting in the sep- arate backbox.
Page 38: Ann-Bus Audio Panel Control
Product Description Accessories ANN-RLY Board Layout and Connection to FACP  Figure 1.15 illustrates the ANN-RLY board showing locations of screw terminals for connection to the FACP and the DIP switches for selecting the ANN-BUS ID number. ANN-BUS (ID#) Address DIP switch Ground Wire ANN-RLY attaches to chassis...
Page 39 Accessories Product Description Examples: • FACP Input programmed to Zone 33 goes into alarm, the programmed message for Zone 33 [Message 1, 2, 3, 4 or 5] will play over the ACC-25/50ZS Series output circuit 1 which corresponds to FACP Zone 33. •...
Page 40: 7: Legacy Acs Annunciators
Product Description Getting Started 1.8.7 Legacy ACS Annunciators WARNING: RISK OF ELECTRICAL SHOCK AND EQUIPMENT DAMAGE DISCONNECT ALL SOURCES OF POWER (AC AND DC) BEFORE INSTALLING OR REMOVING ANY MODULES OR WIRING. The legacy ACS annunciators may not be used if new ANN-BUS annunciators are being used due to incompatible serial communication protocols.
Page 41 Getting Started Product Description • Enter Autoprogramming (refer to “Autoprogram” on page 66). • Resolve Programming Conflicts. • Go to Point Program to Enter Specific Data (refer to “Point Program” on page 67). Use the right and left arrow keys to navigate between devices. MS-9600LS Series Manual —...
Page 42: Section 2: Installation
Section 2: Installation The cabinet may be either semi-flush or surface mounted. The cabinet mounts using key slots and two 0.250” (6.35 mm) diameter holes located in the backbox. The key slots are located at the top of the backbox and the two securing holes at the bottom. Carefully unpack the system and check for shipping damage.
Page 43 Mounting Installation Main Circuit Board on Chassis mounting tab holes ACK/STEP EVENT ALARM SILENCE ENTER DRILL HOLD 2 SEC MODE RESET RECALL mounting studs mounting tabs grounding stud: attach solid earth ground wire (refer to mounting slots “AC Power and Earth Ground Connection”...
Page 44 Installation Mounting 3.37 cm 3.37 cm 5.1 cm 1.325“ 2.00“ 2.00“ 1.325“ 2.00“ 2.00“ 2.00“ 2.00“ 2.00“ 1.625“ (4.128 cm) Semi-Flush Mounting Do not recess box more than 3.875” into wall to avoid covering Hinge Slot for venting holes on top of optional Dress Panel box.
Page 45 Mounting Installation Depth = 5.207" (13.23 cm) Depth = Door = 16.821" (42.73 cm) 5.325" Backbox = 16.65" (42.29 cm) (13.526 cm) Door = 19.26" (48.92 cm) Backbox = 19.0" (48.26 cm) Left Side Right Side Bottom Figure 2.3 FACP Cabinet Dimensions MS-9600LS Series Manual —...
Page 46: Power
Installation Power 2.2 Power WARNING: RISK OF ELECTRICAL SHOCK AND EQUIPMENT DAMAGE SEVERAL DIFFERENT SOURCES OF POWER CAN BE CONNECTED TO THIS PANEL. DISCON- NECT ALL SOURCES OF POWER BEFORE SERVICING. THE PANEL AND ASSOCIATED EQUIPMENT MAY BE DAMAGED BY REMOVING AND/OR INSERTING CARDS, MODULES OR INTERCONNECTING CABLES WHILE THIS UNIT IS ENERGIZED.
Page 47: 3: Special Application Dc Power Output Connection
Relays Installation 2.2.3 Special Application DC Power Output Connection All Special Application DC power outputs are power-limited. Power-limited Resettable Power Power-limited Nonresettable Power #1 Power-limited Nonresettable Power #2 1.5 amperes max., 24 VDC nominal 1.5 amperes max., 24 VDC nominal 1.5 amperes max.
Page 48: 1: Configuring Nacs
Installation Notification Appliance Circuits The following sections describe the configuration and wiring of Style Y and Style Z Notification Appliance Circuits on the FACP main circuit board. The NACs are configured for Style Y (Class B) from the factory. Refer to “Configuring NACs” on page 48 for information on changing the NAC configuration to Style Z (Class A) and preparing the NACKEY configuration card located in JP8, when installing a 4XTMF Transmitter Module.
Page 49: 2: Style Y (Class B) Nac Wiring
Notification Appliance Circuits Installation 2.4.2 Style Y (Class B) NAC Wiring 4 Style Y (Class B) Notification Appliance Circuits, supervised and power-limited - 4.7K ohm, ½ watt P/N:71252 UL-listed NAC 1 NAC 3 NAC 4 NAC 2 Polarized Bells Polarized Bells Polarized Strobes Polarized Strobes Polarized Horns...
Page 50: Power-Limited Wiring Requirements
Installation Power-limited Wiring Requirements 2.5 Power-limited Wiring Requirements Power-limited and nonpower-limited circuit wiring must remain separated in the cabinet. All power-limited circuit wiring must remain at least 0.25” (6.35 mm) away from any nonpower-lim- ited circuit wiring and nonpower-limited circuit wiring must enter and exit the cabinet through dif- ferent knockouts and/or conduits.
Page 51: Optional Modules And Devices
Optional Modules and Devices Installation 2.6 Optional Modules and Devices WARNING: RISK OF ELECTRICAL SHOCK AND EQUIPMENT DAMAGE DISCONNECT ALL SOURCES OF POWER (AC AND DC) BEFORE INSTALLING OR REMOVING ANY MODULES OR WIRING. FACP Keypad/Display Removal Removal of the keypad/display is normally not necessary. If, however, it becomes necessary to replace the keypad/display, access the auxiliary trouble bus connectors at J16 and J17 or install the DACT-UD2 option module on J2, the Keypad/Display can be removed by inserting a Phillips screwdriver into each of the three holes located in the flexible covering of the Keypad/Display and...
Page 52: 1: Dact-Ud2 Installation
Installation Optional Modules and Devices 2.6.1 DACT-UD2 Installation WARNING: RISK OF ELECTRICAL SHOCK AND EQUIPMENT DAMAGE DISCONNECT ALL SOURCES OF POWER (AC AND DC) BEFORE INSTALLING OR REMOVING ANY MODULES OR WIRING. The DACT-UD2 Digital Alarm Communicator/Transmitter, which is supplied standard with the MS-9600UDLS/E, transmits system status to UL listed Central Station receivers via the public switched telephone network.
Page 53 Optional Modules and Devices Installation The following steps must be followed when installing the DACT-UD2 module: Remove all power (AC and DC) from FACP before proceeding with installation Remove all main circuit board mounting screws (6 locations) and the 4XTMF module standoffs (2 locations), unplug the power supply cable from J1 and lift the main circuit board assembly off the chassis (refer to Figure 2.10) Remove the Keypad/Display from the main circuit board as described in the beginning of this...
Page 54 Installation Optional Modules and Devices Mounting Screw Mounting Screw male/female standoff Figure 2.13 DACT-UD2 Installation on Standoffs Reinstall Keypad/Display on the main circuit board by positioning the unit over the appropriate standoffs and securing with screws which were loosened in step 3 Remount the main circuit board assembly to the chassis using screws and standoffs in their original locations.
Page 55: 2: 4Xtmf Transmitter Module Installation
Optional Modules and Devices Installation Primary Lines Secondary Lines Incoming Telco Phone Incoming Telco Lines Phone Lines Green Wire Ring Red Wire Green Wire Ring Ring To premises phones To premises phones Red Wire Ring Note: Shorting bars inside RJ31X Jack removed during male plug insertion Secondary Phone Line SEC 7 foot cable...
Page 56 Installation Optional Modules and Devices Remote Station Service (NFPA 72 Remote Station Fire Alarm Systems) - Intended for connec- tion to a polarity reversal circuit or a Remote Station receiving unit having compatible rat- ings: Maximum load for each circuit: 10 mA Reverse polarity output voltage: 24 VDC Remote Alarm and Remote Trouble wiring can leave the building Before installing the module, place the disconnect switch to the right (disconnect) position to pre-...
Page 57: 3: Auxiliary Trouble Input (J16 & J17)
Optional Modules and Devices Installation When the installation has been complete, enable the 4XTMF module by sliding the disconnect switch to the left Test system for proper operation Standoff Standoff Cut Jumper JP6 J10 & J11 Connectors 4XTMF FACP Figure 2.16 4XTMF Connectors to FACP Connectors NOTE: Jumper JP5 on the FACP main circuit board can be used to configure the FACP supervisory relay for operation with the 4XTMF module.
Page 58: 5: Printer/Pc
Installation Optional Modules and Devices Carefully plug connector J3 on the SLC-2LS module into connector J3 on the MS-9600LS/MS-9600UDLS main circuit board, being careful not to bend any pins Secure the SLC-2LS Expander Module to the four standoffs installed in step 2 with the four supplied screws (or the screws removed in step 2) Connect the SLC wiring and devices to TB8 on the SLC Expander Module.
Page 59: 6: Annunciators
Optional Modules and Devices Installation installation details. Refer to “ANN-BUS Options” on page 121 for programming information. CAUTION: POSSIBLE EQUIPMENT DAMAGE DO NOT CONNECT A PRINTER OR PC TO THE FACP IF A GROUND FAULT (ZERO IMPED- ANCE TO GROUND) EXISTS ON THE CONTROL PANEL. CIRCUIT DAMAGE MAY RESULT. REMOVE ALL POWER (AC AND DC) BEFORE INSTALLING OR REMOVING ANY WIRING.
Page 60: Legacy Acm Series Annunciators
Installation Optional Modules and Devices Legacy ACM Series Annunciators ACM and AFM Series Annunciators provide visual indications of FACP status in remote locations. Refer to the appropriate annunciator manual for information on installation, wiring and operation. MS-9600LS Series Manual — P/N 52646:B2 2/12/2010...
Page 61: Section 3: Programming
Section 3: Programming 3.1 Programming Data Entry Programming can be accomplished using the FACP keypad or by connecting an optional standard computer keyboard. The keyboard can be connected to the PS-2 connector J7 on the control panel main circuit board. Local or remote programming and editing can also be accomplished using the DACT-UD2 Digital Alarm Communicator/Transmitter which is optional for the MS-9600LS and supplied standard with the MS-9600UDLS.
Page 62: User Programming
Programming User Programming 3.2 User Programming The FACP is completely field programmable and requires no special software skills. While pro- gramming the FACP, the fire protection capabilities of the control panel are enabled. Program- ming mode will time-out following 10 minutes of inactivity. Site-specific programming may be accomplished in three ways: •...
Page 63: Initial Power-Up
Initial Power-up Programming Exit Programming or Read Status The programmer can exit Read Status or Programming mode by repeatedly pressing the keypad ESC (Escape) key until the display reads System All Normal. Ten minutes of inactivity will also cause the FACP to exit Programming mode. Note that the data which is entered during Program- ming mode is not saved until the programmer exits this mode by repeatedly pressing the ‘ESC’...
Page 64 Programming Programming and Passwords Change” on page 135. If an invalid password is entered, the blinking cursor will return to the first password character position. To exit Programming or Read Status mode at any time, press the ESC (Escape) key repeatedly. Note that Programming mode must be exited using the ESC key in order to store the program data entered during this mode.
Page 65: Master Programming Level
Master Programming Level Programming 3.6 Master Programming Level When the Master Program Level password is entered, the control panel will enter user Program- ming mode. In this mode, the piezo sounder remains off, the trouble relay is activated and the sys- tem Trouble LED flashes until Programming mode is exited.
Page 66: 1=Autoprogram
Programming Master Programming Level 3.6.1 Autoprogram PROGRAMMING Pressing 1 while viewing Programming Screen #1, will select the Autoprogram option, which 1=AUTOPROGRAM prompts the control panel to poll all devices installed on one or both SLC loops. The primary pur- 2=POINT PROGRAM 3=ZONE SETUP pose of autoprogramming is to allow the installer a fast and easy way to bring the system on-line as quickly as possible.
Page 67: 2: Point Program
Master Programming Level Programming 3.6.2 Point Program PROGRAMMING The Point Program option allows the programmer to add a new addressable device to an SLC loop, 1=AUTOPROGRAM delete an existing device from a loop or change the programming for an existing device. Pressing 2=POINT PROGRAM 3=ZONE SETUP 2, while viewing Programming Screen #1, will select the Point Program option and display the fol-...
Page 68 Programming Master Programming Level A flashing cursor will appear in the position of the first asterisk to the left. The programmer keys in the three digit detector address, such as 005. When the last digit is keyed-in, the following screen will be displayed: DETECTOR TYPE 1=SMOKE(PHOTO) 2=USER-DEFINED-1...
Page 69 Master Programming Level Programming Edit Detector  The programmer can change a detectors existing or factory default programming by pressing 3 in the Detector Screen. The following screen will be displayed: EDIT DETECTOR ENTER POINT ADDRESS Edit Detector Screen A flashing cursor will appear in the position of the first asterisk to the left. The programmer keys in the three digit detector address, such as 017.
Page 70 Programming Master Programming Level If the selected address has been added to programming and a detector (such as a photoelectric detector) with the selected address is physically installed on the SLC and is communicating with the control panel, the following will be displayed: NORMAL SMOKE (PHOTO) ********************* ZNNN...
Page 71 Master Programming Level Programming The following examples show the editing of a photoelectric smoke detector with address 017, located on the first SLC loop: EDIT DETECTOR 1D017 1=ENABLED 2=TYPE SMOKE(PHOTO) 3=VERIFICATION Edit Detector Screen #2 EDIT DETECTOR 1D017 1=WALKTEST 2=PAS 3=PRE-SIGNAL Edit Detector Screen #3 EDIT DETECTOR 1D017...
Page 72 Programming Master Programming Level Pressing the down arrow key will display additional detector types as indicated in the following table: Detector Type Action When Activated Smoke Photo Fire Alarm User-Defined-1 same as previous (Smoke Photo) Smoke Ion Fire Alarm User-Defined-2 same as previous (Smoke Ion) Heat Detect Fire Alarm...
Page 73 Master Programming Level Programming • Program the desired zone or zones to be activated by this detector, in this example Z001 • Program an output, such as a control module that is to be activated by detector 005 by assigning the same zone to it; in this example Z001 •...
Page 74 Programming Master Programming Level Note that Z** represents the Zone Number(s) corresponding to this device. The factory default for an unprogrammed device is Z00 for general alarm zone. A flashing cursor will appear on the first 0 to the left. Enter the two digit number corresponding to the zone that is to be assigned to this device.
Page 75 Master Programming Level Programming Pressing 1 while viewing the Noun/Adjective Screen will cause the following screen(s) to be dis- 1=STANDARD ADJECTIVE played. Note that the keyboard down arrow key must be pressed to see all the Adjective screens. 2=STANDARD NOUN Press the number corresponding to the adjective that is to be used as a descriptor for the location of 3=CUSTOM ADJECTIVE 4=CUSTOM NOUN...
Page 76 Programming Master Programming Level Pressing 2 while viewing the Noun/Adjective Screen will cause the following screen(s) to be dis- 1=STANDARD ADJECTIVE played. Note that the keyboard down arrow key must be pressed to see all the Noun screens. Press 2=STANDARD NOUN the number corresponding to the noun that is to be used as a descriptor for the location of the detec- 3=CUSTOM ADJECTIVE 4=CUSTOM NOUN...
Page 77 Master Programming Level Programming Pressing 3 or 4 while viewing the Noun/Adjective Screen will display screens similar to the previ- 1=STANDARD ADJECTIVE ous Adjective and Noun Screens. The new screens will list custom Adjectives and Nouns which 2=STANDARD NOUN have been programmed into the control panel using the PS-Tools programming kit. These descrip- 3=CUSTOM ADJECTIVE 4=CUSTOM NOUN tors are selected as described in the previous sections.
Page 78: Module Programming
Programming Master Programming Level With the cursor on the last letter of the Noun field, press the zero key again to increment the room number to 305. Press the right arrow key to advance the zone field. Select a zone number from 00 to 99. Z00 (default zone) is the general alarm zone. Z01 through Z99 may be selected to link software zones.
Page 79 Master Programming Level Programming Pressing 1 for Control Module or 2 for Monitor Module will cause the following screen to be dis- played: ADD MODULE MODULE# IS ADDED Add Module Screen #3 The programmer can continue adding modules by pressing the ESC or left arrow key which will return the display to the Add Module Screen #1.
Page 80 Programming Master Programming Level A flashing cursor will appear in the position of the first asterisk to the left. The programmer keys in the three digit module address, such as 012. When the last digit is keyed-in, if the selected address has not been added to programming, a screen showing information about a device that is installed with a lower address, closest to the selected address, will be displayed.
Page 81 Master Programming Level Programming If the selected address corresponds to a monitor module, a screen displaying information about the module with the selected address will be displayed as illustrated in the following: NORMAL MONITOR ZNNN 1M012 EDIT MONITOR 1M012 1=ENABLED 2=TYPE MONITOR...
Page 82 Programming Master Programming Level Type Monitor EDIT MONITOR 1=ENABLED The FACP response to the activation of a user-defined type is the same as most previous standard 2=TYPE MONITOR types in the list, thus allowing a variety of user-defined types and responses. To select the type of monitor module being programmed, press the 2 key while viewing the Edit Monitor Screen #2.
Page 83 Master Programming Level Programming Monitor module type selection will affect the function of the point as follows: Monitor Type Action When Activated Pull-Station Fire Alarm User-Defined-1 same as previous (Pull-Station) Waterflow Fire Alarm Delayed User-Defined-2 same as previous (Waterflow) Monitor Fire Alarm User-Defined-3 same as previous (Monitor)
Page 84 Programming Master Programming Level Pre-signal EDIT MONITOR 1=PRE-SIGNAL To enable the Pre-signal feature, press 1 while viewing Edit Monitor Screen #3 until the display reads Pre-signal Yes. Each press of the 1 key will cause the display to toggle between Pre-signal Yes and Pre-signal No.
Page 85 Master Programming Level Programming Pressing 1 while viewing the Noun/Adjective Screen will cause the following screen(s) to be dis- 1=STANDARD ADJECTIVE played. Note that the keyboard down arrow key must be pressed to see all the Adjective screens. 2=STANDARD NOUN 3=CUSTOM ADJECTIVE Press the number corresponding to the adjective that is to be used as a descriptor for the location of 4=CUSTOM NOUN...
Page 86 Programming Master Programming Level Pressing 2 while viewing the Noun/Adjective Screen will cause the following screen(s) to be dis- 1=STANDARD ADJECTIVE played. Note that the keyboard down arrow key must be pressed to see all the Noun screens. Press 2=STANDARD NOUN 3=CUSTOM ADJECTIVE the number corresponding to the noun that is to be used as a descriptor for the location of the mon- 4=CUSTOM NOUN...
Page 87 Master Programming Level Programming Description EDIT MONITOR 1=NOUN/ADJECTIVE The Description selection allows the programmer to enter additional information about the monitor 2=DESCRIPTION ***************** module currently being programmed. This information will be displayed as part of the device label on the LCD display. Pressing 2 while viewing Edit Monitor Screen #5 will cause the following Edit Monitor Screen #5 screen to be displayed: DESCRIPTION...
Page 88 Programming Master Programming Level Edit Module Screen for Control Modules  The programmer can change a module’s existing or factory default programming by pressing 3 in the Modules Screen. The following screen will be displayed: MODULES 1=ADD 2=DELETE 3=EDIT EDIT MODULE ENTER MODULE ADDRESS Modules Screen Edit Module Screen...
Page 89 Master Programming Level Programming To change the programming for the displayed module, press the keyboard down arrow key to view the following Edit Control screens: EDIT CONTROL 1=ENABLED 2=TYPE CONTROL 3=SILENCEABLE Edit Control Screen #2 EDIT CONTROL 1=WALKTEST 2=ZONE ASSIGNMENT 00 ** ** ** ** Edit Control Screen #3 EDIT CONTROL...
Page 90 Programming Master Programming Level The following table contains control module type codes and their functions which are displayed in the Control Type screens: Control Type Special Function Bell Circuit NAC Type - supervised Horn Circuit NAC Type - supervised Sounders NAC Type - supervised Relay Ignore Open Circuit...
Page 91 Master Programming Level Programming remaining zones can be left blank or programmed as general alarm zones Z00. When all desired changes have been made, press the Enter key to store the zone assignments. The display will return to the Edit Control Screen #3. Noun/Adjective EDIT CONTROL 1=NOUN/ADJECTIVE...
Page 92 Programming Master Programming Level Pressing 1 while viewing the Noun/Adjective Screen will cause the following screen(s) to be dis- 1=STANDARD ADJECTIVE played. Note that the keyboard down arrow key must be pressed to see all the Adjective screens. 2=STANDARD NOUN 3=CUSTOM ADJECTIVE Press the number corresponding to the adjective that is to be used as a descriptor for the location of 4=CUSTOM NOUN...
Page 93 Master Programming Level Programming Pressing 2 while viewing the Noun/Adjective Screen will cause the following screen(s) to be dis- 1=STANDARD ADJECTIVE 2=STANDARD NOUN played. Note that the keyboard down arrow key must be pressed to see all the Noun screens. Press 3=CUSTOM ADJECTIVE the number corresponding to the noun that is to be used as a descriptor for the location of the con- 4=CUSTOM NOUN...
Page 94 Programming Master Programming Level Description EDIT CONTROL 1=ADJECTIVE/NOUN The Description selection allows the programmer to enter additional information about the control 2=DESCRIPTION module currently being programmed. This information will be displayed as part of the device label on the display. Pressing 2 while viewing Edit Control Screen #4 will cause the following screen to Edit Control Screen #4 be displayed: DESCRIPTION...
Page 95: 3=Zone Setup
Master Programming Level Programming 3.6.3 Zone Setup Pressing 3 while viewing Programming Screen #1 will access the Zone Setup screens as illustrated PROGRAMMING 1=AUTOPROGRAM below: 2=POINT PROGRAM 3=ZONE SETUP ZONE SETUP Programming Screen #2 1=ENABLE 2=DISABLE 3=ZONE 97 98 99 Zone Setup Screen #1 ZONE SETUP 1=ZONES INSTALLED...
Page 96: Disable
Programming Master Programming Level Disable ZONE SETUP 1=ENABLE Pressing 2 for Disable, while viewing Zone Setup Screen #1, will display the following screen: 2=DISABLE 3=ZONE 97 98 99 Zone Setup Screen #1 ZONE TO DISABLE Disable Screen This screen allows the programmer to disable zones, one at a time. A flashing cursor appears next to the Z, prompting the programmer to enter a two digit zone number (01 - 99).
Page 97: Zones Installed
Master Programming Level Programming Zones Installed ZONE SETUP 1=ZONES INSTALLED Pressing 1 for Zones Installed, while viewing Zone Setup Screen #2, will display a screen similar to 2=ZONES ENABLED the following: 3=ZONES DISABLED Zone Setup Screen #2 ZONES INSTALLED 00 01 02 03 04 05 Zones Installed Screen This display will show all of the zones that have been programmed into the control panel.
Page 98: Zone Type
Programming Master Programming Level Zone Type ZONE SETUP 1=ZONE TYPES Zone Types must be programmed only if a DACT, programmed for zone reporting, is installed on 2=ZONES AVAILABLE the control panel. Pressing 1 for Zone Types, while viewing Zone Setup Screen #3, will display a 3=ZONE MESSAGE screen similar to the following: Zone Setup Screen #3...
Page 99: Zones Available
Master Programming Level Programming Zones Available ZONE SETUP 1=ZONE TYPES Pressing 2 while viewing Zone Setup Screen #3 will display the following screen: 2=ZONES AVAILABLE 3=ZONE MESSAGE ZONES AVAILABLE Zone Setup Screen #3 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 The display will show all of the zones that are still available for programming.
Page 100: Loop Protocol
Programming Master Programming Level Loop Protocol Loop Protocol refers to the SLC loop mode of operation. Refer to “Wire Requirements” on page 196 for wire specifications based upon SLC protocol. Two modes of operation are available: LiteSpeed and CLIP mode. CLIP mode (Classic Loop Interface Protocol) is used for the older leg- acy addressable devices such as the M300 Series modules and detectors.
Page 101: Trouble Reminder
Master Programming Level Programming Pressing 2 for System Setup, while viewing Programming Screen #2, will cause the following PROGRAMMING 1=LOOP SETUP screens to be displayed: 2=SYSTEM SETUP 3=VERIFY LOOPS SYSTEM SETUP Programming Screen #2 1=TROUBLE REM 2=BANNER 3=TIME-DATE System Setup Screen #1 SYSTEM SETUP 1=TIMERS 2=NAC...
Page 102 Programming Master Programming Level Pressing 1 while viewing the Banner Screen will select the blank factory default banner setting and BANNER 1=FACTORY display the following screen: 2=USER DEFINED FACTORY BANNER Banner Screen Factory Banner Screen Pressing the Enter key will store this selection in nonvolatile memory and return the display to the Banner Screen.
Page 103: Time-Date
Master Programming Level Programming Time-Date SYSTEM SETUP 1=TROUBLE REM The control panel time and date can be changed by pressing 3 while viewing the System Setup 2=BANNER Screen #1. The following screen will be displayed: 3=TIME-DATE System Setup Screen #1 TIME AND DATE 1=TIME 10:00 AM...
Page 104 Programming Master Programming Level digit is entered. After the last year digit is entered, the display will return to the Time-Date Screen which will show the new date entry. If an error is made while entering a digit, press the CLR key to delete the entire entry and beginning again.
Page 105: Timers
Master Programming Level Programming Timers SYSTEM SETUP 1=TIMERS Timer delays for PAS, Pre-signal and waterflow activation can be programmed by pressing 1 while 2=NAC viewing System Setup Screen #2. The following screen will be displayed: 3=RELAYS System Setup Screen #2 TIMERS 1=PAS DELAY 2=PRE SIGNAL...
Page 106 Programming Master Programming Level A flashing cursor is positioned in the lower left corner of the display. Enter a delay time consisting of three digits, such as 009 for nine seconds. Upon entering the third digit, the time delay will be stored in the control panel memory and the display will return to the Delay Screen which will indi- cate the new delay time.
Page 107: Nac (Notification Appliance Circuit)
Master Programming Level Programming Pressing 2 while viewing AC Loss Delay Screen #1 will display the following screen: AC LOSS DELAY RANGE 00-23 AC Loss Delay Screen #2 A flashing cursor will appear in the lower left corner of the display. The factory default setting is 02 hours.
Page 108 Programming Master Programming Level The following screens will be displayed for either selection: NAC # 1=ENABLED 2=TYPE BELL 3=SILENCEABLE NAC Screen #1 NAC # 1=AUTO SILENCE 2=CODING TEMPORAL NAC Screen #2 NAC # 1=ZONE 00 00 00 00 00 2=SIL INHIBITED NAC Screen #3 NAC # 1=SYNC TYPE...
Page 109 Master Programming Level Programming Type  NAC # 1=ENABLED The main circuit board NAC type can be programmed by pressing 2 while viewing NAC Screen #1. 2=TYPE The following screen will be displayed. Press the down arrow key to view additional screens: 3=SILENCEABLE NAC Screen #1 NAC TYPE...
Page 110 Programming Master Programming Level Auto Silence  NAC # 1=AUTO SILENCE The Auto Silence feature, when enabled, automatically silences all main circuit board silenceable 2=CODING TEMPORAL notification appliances after a programmed length of time. To enable this feature and program the time delay before Auto Silence activation, press 1 while viewing NAC Screen #2.
Page 111 Master Programming Level Programming The programmer can select the notification appliance output by pressing the number corresponding to the desired output. The coding selections are: • Steady - a continuous output with no coding • March Time - 120 ppm (pulse-per-minute) output •...
Page 112: Relays
Programming Master Programming Level Note that Z** represents the Zone Number(s) corresponding to the selected NAC. The factory default for an unprogrammed device is Z00 for general alarm zone. A flashing cursor will appear on the first 0 to the left. Enter the two digit number corresponding to the zone that is to be assigned to this NAC.
Page 113: Canadian Option
Master Programming Level Programming To program Relay 1 or Relay 3, press the number corresponding to the selected relay. Note that Relay 2 is fixed as a Trouble relay. Selecting Relay 2 will have no effect on its programming. The following screen will appear for each relay to be programmed: RELAY # 1=TYPE...
Page 114: Waterflow Silenceable
Programming Master Programming Level The Canadian Options configures the FACP with the following as required by Canada: • The following monitor module type codes are not available: • monitor • non-latching supervisory • non-latching drill • non-latching process monitor • process monitor •...
Page 115: 7: History
Master Programming Level Programming 3.6.7 History PROGRAMMING The History option allows an authorized user to view or erase events which have occurred in the 1=HISTORY control panel. Pressing 1 while viewing Programming Screen #3 will display the History options 2=WALKTEST 3=OPTION MODULES as shown in the following display: Programming Screen #3...
Page 116: 8: Walktest
Programming Master Programming Level 3.6.8 Walktest PROGRAMMING Walktest allows an individual to test the fire alarm system without the necessity to reset the control 1=HISTORY panel after each device activation. Pressing 2 while viewing the Programming Screen #3 will cause 2=WALKTEST 3=OPTION MODULES the following Walktest options to be displayed:...
Page 117: 9: Option Modules
Master Programming Level Programming Pressing 2 for View Points while viewing the Unit In Walktest screen will display one of the follow- ing screens: UNTESTED POINTS NO POINTS IN 1D001 SMOKE (PHOTO) SYSTEM ********************* NOT TESTED If the system has no points installed, the first screen will be displayed. If points are installed, the second screen will be displayed, which allows the viewing of all untested system points and their status relating to the current walktest session.
Page 118: Annunciators/Udact
Programming Master Programming Level Pressing 3 while viewing Programming Screen #3 will display the following screen: OPTION MODULES 1=ANNUNCIATORS/UDACT 2=ONBOARD DACT 3=PRINTER/PC PR4800 Options Screen Note that PR4800 in the display indicates that a supervised printer, configured for 4800 baud, has been previously programmed into the system.
Page 119 Master Programming Level Programming ACS Options  ANNUNCIATORS Pressing 2 for ACS Options while viewing the Annunciators screen, will display the following 1=TERM OPTIONS screen: 2=ACS OPTIONS 3=ANN-BUS OPTIONS Annunciator Screen ACS OPTIONS 1=ACS ENABLED 2=ACS INSTALLED 3=UDACT Pressing 1 while viewing the ACS Options screen will cause the display to toggle between ACS Enabled Yes and ACS Enabled No.
Page 120 Programming Master Programming Level Annunciator addressing is specific to the FACP control panel. The following table describes the annunciator addresses and the corresponding addressable devices that will be annunciated at each annunciator address. ACS Annunciator Address Annunciator Displays the Following Points 8 General System Status Points &...
Page 121 Master Programming Level Programming ANN-BUS Options  ANNUNCIATORS Pressing 3 for ANN-BUS Options, while viewing the Annunciators screen, will cause the following 1=TERM OPTIONS screens to be displayed:. 2=ACS OPTIONS 3=ANN-BUS OPTIONS ANN-BUS Annunciator Screen 1=ENABLED 2=MODULES INSTALLED 3=AUTO-CONFIGURE ANN-BUS Screen #1 ANN-BUS 1=ANN-S/PG OPTIONS 2=ANN-80 OPTIONS...
Page 122 Programming Master Programming Level Pressing 1 for Type will display the following screens: ANN-BUS MODULE TYPE 1=NOT INSTALLED 2=ANN-80 MODULE 3=ANN-I/O MODULE Module Type Screen #1 ANN-BUS MODULE TYPE 1=ANN-S/PG MODULE 2=ANN-LED MODULE 3=ANN-RLY MODULE Module Type Screen #2 ANN-BUS MODULE TYPE 1=ANN-AUDIO Module Type Screen #3 Press the number corresponding to the module type that is installed with the selected address.
Page 123 Master Programming Level Programming ANN-I/O Options Pressing 2 for Module Options while viewing ANN-BUS Address Screen when the ANN-I/O option is selected will display the following screen: ANN-I/O ADDR # SLC 1 MOD 001-030 ACTIVE LEDS ONLY ANN-I/O Address Screen #1 ANN-I/O ADDR # 1=POINT/ZONE POINT...
Page 124 Programming Master Programming Level Trouble Zone 33 Zone 73 Alarm Silenced Zone 34 Zone 74 Earth Fault Zone 35 Zone 75 Battery Fault Zone 36 Zone 76 Charger Fault Zone 37 Zone 77 NAC Fault Zone 38 Zone 78 Disabled Zone 39 Zone 79 Zone 00...
Page 125 Master Programming Level Programming ANN-I/O Point Option If Point is selected as the module option, the first ten LEDs on the first ANN-I/O module will display the system status information. The remaining 30 LEDs on the first module and 40 LEDs on each additional module will display the active/alarm status of each point in the Point Range programmed for that particular module.
Page 126 Programming Master Programming Level ANN-LED Options Pressing 2 for Module Options while viewing ANN-BUS Address Screen when the ANN-LED option is selected will display the following screen: ANN-LED ADDR # LOOP1 DET 1-10 ALARM,SUPERV,TBL ANN-LED Address Screen #1 ANN-LED ADDR # 1=POINT/ZONE 2=ALARM/ATS ANN-LED Address Screen #2...
Page 127 Master Programming Level Programming ANN-LED Zone Option - Alarm Only (for use with ANN-RLED module) If Zone is selected as the module option, and the module is programmed to annunciate alarms only, the first ten LEDs on the first ANN-LED module will display the system status information. The remaining 30 LEDs on the first module and the last 30 LEDs on the remaining modules will display the active/alarm status of each zone in the Zone Range programmed for that particular module.
Page 128 Programming Master Programming Level ANN-LED Zone Option - Alarm, Trouble and Supervisory If Zone is selected as the module option, and the module is programmed to annunciate alarms, troubles and supervisories, the first ten LEDs on the first ANN-LED module will display the sys- tem status information.
Page 129 Master Programming Level Programming ANN-LED Point Option - Alarm Only (for use with ANN-RLED module) If Point is selected as the module option and the module is programmed to annunciate alarms only, the first ten LEDs on the first ANN-LED module will display the system status information. The remaining 30 LEDs on the first module and the last 30 LEDs on each additional module will dis- play the active/alarm status of each point in the Point Range programmed for that particular mod- ule.
Page 130 Programming Master Programming Level ANN-LED Point Option - Alarm, Trouble and Supervisory If Point is selected as the module option, and the module is programmed to annunciate alarms, troubles and supervisories, the first ten LEDs on the first ANN-LED module will display the sys- tem status information.
Page 131 Master Programming Level Programming ANN-RLY Options Pressing 2 for Module Options while viewing ANN-BUS Address Screen when the ANN-RLY option is selected will cause the following screen to be displayed: ANN-RLY - ADDR. # 1=RELAY 1 ZONE 00 2=RELAY 2 ZONE 01 3=RELAY 3 ZONE 02...
Page 132 Programming Master Programming Level ANN-S/PG (Print) Options ANN-BUS The Print option allows the programmer to configure the optional printer. Pressing 1 while viewing 1=ANN-S/PG OPTIONS ANN-BUS screen #2 will display the following screens: 2=ANN-80 OPTIONS ANN-S/PG OPTIONS ANN-BUS Screen #2 1=PORT 2=PRINTER SUPV 3=OFFLINE TIMER...
Page 133 Master Programming Level Programming ANN-80 Options ANN-BUS Pressing 2 while viewing ANN-BUS screen #2 will display the following screen: 1=ANN-S/PG OPTIONS 2=ANN-80 OPTIONS ANN-80 OPTIONS ANN-BUS Screen #2 1=PIEZO ENABLE 2=LOCK ENABLE 3=ACK BTN ENABLE ANN-80 Options Screen #1 ANN-80 OPTIONS 1=SIL BTN ENABLE 2=RST BTN ENABLE 3=DRL BTN ENABLE...
Page 134: On Board Dact
Programming Master Programming Level On Board DACT OPTION MODULES The Onboard DACT (Digital Alarm Communicator/Transmitter) provides communication to a 1=ANNUNCIATORS/UDACT Central Station. Pressing 2 while viewing the Option Module Screen will allow programming of 2=ON BOARD DACT 3=PRINTER/PC the Onboard DACT. Refer to the DACT-UD2 Installation and Programming Manual Document #53037 for detailed information on installing and programming this option.
Page 135: 10: Password Change
Master Programming Level Programming 3.6.10 Password Change PROGRAMMING The factory set passwords, which have been programmed into the control panel, can be changed by 1=PASSWORD CHANGE selecting the Password Change option. Pressing 1 while viewing Programming Screen #4 will 2=CLEAR PROGRAM 3=PROGRAM CHECK cause the following screen to be displayed: Programming Screen #4...
Page 136: 11: Clear Program
Programming Master Programming Level 3.6.11 Clear Program PROGRAMMING Pressing 2 while viewing Programming Screen #4, will select the Clear Program option. This will 1=PASSWORD CHANGE cause the LCD to display the following screens: 2=CLEAR PROGRAM 3=PROGRAM CHECK CLEAR PROGRAM Programming Screen #4 1=WHOLE SYSTEM 2=ALL LOOPS 3=LOOP1...
Page 137: 12: Program Check
Master Programming Level Programming 3.6.12 Program Check PROGRAMMING The Program Check feature allows the programmer to view the zones which have been pro- 1=PASSWORD CHANGE grammed to the Notification Appliance Circuits on the control panel but have not been pro- 2=CLEAR PROGRAM 3=PROGRAM CHECK grammed to Initiating Devices as well as other circuits with no input or output correlations.
Page 138: Maintenance Programming Level
Programming Maintenance Programming Level Pressing 3 while viewing Program Check screen will cause a screen similar to the following to be displayed: ZONES NO OUTPUT 05 07 09 10 11 1D001 The Zone No Output feature allows the programmer to view the zones which have not been pro- grammed to at least one output device (not including general alarm Zone 00).
Page 139: 1: Disable Point
Maintenance Programming Level Programming Note that in the preceding screens, an arrow appears to inform the programmer that additional options can be viewed by pressing the keypad down arrow key, as shown in the following screen. PROGRAMMING 1=WALKTEST 2=SYSTEM 3=ZONE SETUP 3.7.1 Disable Point Pressing 1 for Point Program, while viewing Maintenance Screen #1 will cause the following screens to be displayed:...
Page 140: 2=History
Programming Maintenance Programming Level A flashing cursor will appear in the bottom left corner of the display, prompting for the three digit device address. When the third digit is enter, 001 for example, a screen will appear which will allow enabling or disabling of the selected point, as illustrated in the following example: EDIT DETECTOR 1D001 1=ENABLED Enable/Disable Select Screen...
Page 141: 3: Program Check
Maintenance Programming Level Programming Pressing 2 while viewing the History Screen will cause the following screen to be displayed: ERASE HISTORY PROCEED ? 1=YES 2=NO Erase History Screen Pressing 1 while viewing the Erase History Screen will cause the message ERASING HISTORY, PLEASE WAIT to be displayed.
Page 142: 4: Walktest
Programming Maintenance Programming Level Pressing 2 while viewing the Program Check screen will display a screen similar to the following: ZONES NO INPUT 05 07 09 10 11 1M001 The Zone No Input screen allows the programmer to view the zones which have not been pro- grammed to at least one input device (not including general alarm Zone 00).
Page 143: 5: System
Maintenance Programming Level Programming 3.7.5 System To program the time and date into the control panel, press 2 while viewing Maintenance Screen #2. The following display will appear: SYSTEMS 1=TIME/DATE System Screen Pressing 1 while viewing the System Screen will cause the following screen to be displayed: TIME AND DATE 1=TIME 01:00 AM...
Page 144: 6: Zone Setup
Programming Maintenance Programming Level To change the date, press 2 while viewing the Time and Date Screen. The following screen will be displayed: ENTER DATE MONTH DAY YEAR 01-01-2010 Date Screen A flashing cursor will appear on the left side of the display. Enter the two digit month, two digit day and four digit year.
Page 145 Maintenance Programming Level Programming Pressing 1 while viewing Zone Setup screen #1 will display the following screen: ZONE TO ENABLE Enable Screen A flashing cursor appears to the right of the Z. To enable a zone, enter the two digit zone number (00 - 99).
Page 146: Zones Installed
Programming Maintenance Programming Level nected to the control module can be used to indicate a PAS condition in the control panel. Do not assign Zone 97 to a Notification Appliance Circuit when using this zone to indicate a PAS condi- tion.
Page 147: Zones Disabled
Maintenance Programming Level Programming Zones Disabled Pressing 3 for Zones Disabled, while viewing Zone Setup Screen #2, will display a screen similar to the following: ZONES DISABLED Zones Disabled Screen This display will show all of the zones that are disabled in the control panel. Note that an up and/or down arrow may appear in the upper right corner of the display, indicating that additional screens of zone information exists.
Page 148: Zones Available
Programming Maintenance Programming Level Zone types can be changed by pressing the keypad number key corresponding to the zone in each Zones Installed Screen. Available zone types will be displayed in the resultant screens. For exam- ple, to change the zone type for zone Z02 in the screen illustrated above, press 3. The following screens will be displayed: ZONE TYPE PROG ZONE TYPE PROG...
Page 149: Zone Message
Maintenance Programming Level Programming Zone Message Pressing 3 while viewing Zone Setup Screen #3 will display the following screen: ZONE MESSAGE 1=Z00 NO MESSAGE 2=Z01 MESSAGE 1 3=Z02 NO MESSAGE Pressing the down arrow key will display additional screens for Zones up to Z99. Press the number key corresponding to the Zone to be programmed.
Page 150: Section 4: Operating Instructions
Section 4: Operating Instructions 4.1 Panel Control Buttons 4.1.1 Acknowledge/Step The first press of the Acknowledge/Step key silences the piezo sounder, changes flashing LEDs to steady and also changes the status field on the LCD display from capital letters to small letters. When the piezo is silenced, an acknowledge message is sent to the printer and the history file.
Page 151: Normal Operation
With no alarms or troubles in the system, the display message is System All Normal along with the current time and date as shown below. To set the time and date, refer to the appropriate section in this manual. HONEYWELL LIFE SAFETY SYSTEM ALL NORMAL...
Page 152: Trouble Operation
Operating Instructions Trouble Operation 4.4 Trouble Operation With no alarms in the system, the detection of a trouble will cause the following: • The piezo to pulse 1 second On and 1 second Off • The system Trouble LED to flash one second On and one second Off •...
Page 153: Alarm Operation
Alarm Operation Operating Instructions INV ID - indicating that an incorrect device code (Type ID) has been programmed for an  installed device (for example, Photo has been programmed but an Ion detector has been installed) SW TBL - indicating a module has failed the testing of its Class A switching relay ...
Page 154: Supervisory Operation
Operating Instructions Supervisory Operation Note that the device type, which in this example is PULL STATION, can be any other programma- ble alarm type. The information displayed in the above example provides the following information: • First line in display: –...
Page 155: Process Monitor Operation
Process Monitor Operation Operating Instructions A typical Supervisory event would be displayed as illustrated in the following: ACTIVE SUPERVISORY Z000 10:00A 010810 1M001 Note that, like alarms, supervisory signals latch (except when programmed for supervisory autore- settable) and can be assigned to software zones. Supervisory alarms do not cause resound as do other alarm conditions.
Page 156: Medical Alert Condition Operation
Operating Instructions Medical Alert Condition Operation 4.9 Medical Alert Condition Operation Medical Alert Condition operation will initiate the following events: • The piezo sounder turns on steady • The LCD displays a medical alert message along with the device name, type, address, adjective/noun, associated zones and time/date •...
Page 157: Time Functions: Real-Time Clock
Time Functions: Real-Time Clock Operating Instructions Type Code Supervision The FACP monitors addressable hardware device codes at slow intervals. Mismatch of any type code, compared to the system program, will cause a device trouble. System Alarm Verification The control panel may be programmed to perform alarm verification to help eliminate the nuisance of false alarms.
Page 158: Presignal
Operating Instructions Presignal 4.18 Presignal Presignal option programs an initiating device to delay the activation of NACs and/or control mod- ules while allowing visual verification by a person. Once a detector or monitor module triggers an alarm, the onboard piezo sounds immediately, but the NACs are not activated for a user pro- grammed time duration of up to three minutes.
Page 159: Special System Timers
Special System Timers Operating Instructions • pressing the Alarm Silence or Acknowledge/Step key will start a timer which inhibits output activation for additional time delay of up to three minutes which is user programmable • second alarm occurring anytime during either time delay will cause immediate activation of all associated outputs PAS operation requires the approval of the local Authority Having Jurisdiction.
Page 160: Walktest
Operating Instructions Walktest all appropriate outputs and indicate the alarm condition at the FACP. If no additional detector alarms occur within 73 seconds of the first alarm (13 second Retard plus 60 second Confirmation), the timer resets and the panel is ready to verify any new detector alarms which may occur. 13 sec.
Page 161: 3=Power
Read Status Operating Instructions Read Status Entry When the operator presses the control panel Enter key, the LCD will display the following: 1=READ STATUS 2=PROGRAMMING 3=REMOTE DOWNLOAD Pressing 1, while this screen is being displayed, will cause the control panel to enter the Read Sta- tus mode which allows the user to view and print the programmed features and status of the control panel.
Page 162: 1=System Point
Operating Instructions Read Status 4.22.1 System Point READ STATUS Pressing 1 while viewing Read Status Screen #1 will cause the following screen to be displayed: 1=SYSTEM POINT 2=ZONES 3=POWER READ SYSTEM POINT Read Status Screen #1 SELECT LOOP 1=LOOP 1 2=LOOP 2 The operator selects the loop containing the device to be read by pressing 1 for Loop 1 or 2 for Loop 2.
Page 163: 2=Zones
Read Status Operating Instructions Pressing the down arrow key, while viewing the screen shown on the previous page, will allow the operator to view additional programming information about the selected device, such as: • Enable/Disable Status • Device Type • Alarm Verification On/Off •...
Page 164 Operating Instructions Read Status 4.22.3 Power Pressing 3 while viewing Read Status Screen #1 will display the following screens: POWER BATTERY 27.21V 24 V RST 25.31V Zones Screen #1 POWER CHARGER 28.36V NAC 1 -2.39V NAC 2 -2.39V Zones Screen #2 POWER NAC 3 -2.39V...
Page 165: 4: Trouble Reminder
Read Status Operating Instructions 4.22.4 Trouble Reminder Pressing 1 while viewing Read Status Screen #2 will display the following screen: READ STATUS 1=TROUBLE REMINDER 2=TIMERS TROUBLE REMINDER 3=NACS TROUBLE REM Read Status Screen #2 The screen indicates whether the Trouble Reminder feature is On or Off. 4.22.5 Timers Pressing 2 while viewing Read Status Screen #2 will cause the following Timer screens to be dis- played:...
Page 166: 6: Nac
Operating Instructions Read Status 4.22.6 NAC Pressing 3 while viewing Read Status Screen #2 will display the following screen: 1=NAC 1 3=NAC 3 2=NAC 2 4=NAC 4 Note that 3=NAC 3 and 4=NAC 4 will only be displayed if the NACKEY NAC option card is installed, in JP8 of the main circuit board, for Class B operation.
Page 167: 8: Program Check
Read Status Operating Instructions 4.22.8 Program Check Pressing 2 while viewing Read Status Screen #3 will cause a screen similar to the following to be displayed: PROGRAM CHECK 1=NACS NO INPUT 2=ZONES NO INPUT 3=ZONES NO OUTPUT Pressing 1 while viewing the Program Check screen will display a screen which will indicate if any input zones have not been programmed to one of the Notification Appliance Circuits.
Page 168 Operating Instructions Read Status The Annunciator Screen indicates if Terminal mode options are enabled or disabled. Pressing 2 for ACS Options while viewing the Annunciator Screen allows the operator to view the ACS Options screen: ACS OPTIONS ACS ENABLED 2=ACS ADDRESSES UDACT ENABLED ACS Options Screen The ACS Options screen indicates if the ACS option has been enabled YES or disabled NO.
Page 169: 11: Phone Line
Read Status Operating Instructions 4.22.11 Phone Line Pressing 2 while viewing Read Status Screen #4 will display the following screen: PHONE LINE PRIMARY TOUCHTONE SECONDARY TOUCHTONE 3=SUPERV PHONE LINE The second and third lines of this screen indicate that both the Primary and Secondary phone lines have been configured for touchtone dialing operation.
Page 170: 13: Service Terminal
Operating Instructions Read Status 4.22.13 Service Terminal Pressing 1 while viewing Read Status Screen #5 will display the following screens: READ STATUS 1=SERVICE TERMINAL 2=PRINTER/PC SERVICE TERMINAL 3=PRINT RING COUNT Read Status Screen #5 Service Terminal Screen The Ring Count is displayed in the Service Terminal Screen. A Ring Count value of 00 would indi- cate that calling is disabled.
Page 171: 15: Print
Read Status Operating Instructions 4.22.15 Print To print program data or control panel status, press 3 while viewing Read Status Screen #5. The following screens will be displayed: READ STATUS 1=SERVICE TERMINAL 2=PRINTER/PC PRINT 3=PRINT 1=HISTORY Read Status Screen #5 2=WALKTEST LOG 3=DETECTOR DATA Print Screen #1...
Page 172 Operating Instructions Read Status Drift Compensation Drift compensation uses software algorithms that identify and compensate for long-term changes in the data readings from each addressable smoke detector. These long-term changes in detector data readings are typically caused by dirt and dust accumulation inside the smoke chamber. Drift com- pensation performs the following functions: •...
Page 173: 16: Time-Date
Read Status Operating Instructions 4.22.16 Time-Date The operator can view the daylight savings time and the month and week when daylight savings time will begin and end. Pressing 1 while viewing Read Status Screen #6 will display the following READ STATUS screens: 1=TIME-DATE Read Status Screen #6...
Page 174: Section 5: Power Supply Calculations
Section 5: Power Supply Calculations 5.1 Overview This section contains instructions and tables for calculating power supply currents in alarm and standby conditions. This is a four-step process, consisting of the following: Calculating the total amount of AC branch circuit current required to operate the system Calculating the power supply load current for non-fire and fire alarm conditions and calculating the secondary (battery) load Calculating the size of batteries required to support the system if an AC power loss occurs...
Page 175: 2: How To Use Table 5.3 On Page 176 To Calculate System Current Draw
Calculating the System Current Draw Power Supply Calculations • ‘Secondary’ refers to the control panel’s backup batteries • All currents are given in amperes (A). Table 5.2 shows how to convert milliamperes and microamperes to full amperes. To convert... Multiply Example Milliamperes (mA) to mA x 0.001...
Page 176 Power Supply Calculations Calculating the System Current Draw Table 5.3 contains columns for calculating current draws. For each column, calculate the current and enter the total (in amperes) in the bottom row. When finished, copy the totals from Calculation Column 2 and Calculation Column 3 to Table 5.4 on page 177. Calculation Column 1 Calculation Column 2 Calculation Column 3...
Page 177: Calculating The Battery Size
Calculating the Battery Size Power Supply Calculations 5.4 Calculating the Battery Size Use Table 5.4 to calculate the total Standby and Alarm load in ampere hours (AH). This total load determines the battery size (in AH), required to support the control panel under the loss of AC power.
Page 178: Appendix A: Software Zones
Appendix A: Software Zones A.1 Correlations Setup and configuration of an addressable system is different than a conventional system. In a conventional system, assignment of input devices (smoke detectors, pull stations, heat detectors, etc.) to zones is accomplished through wiring. The wiring is direct from clearly marked panel terminals to any device assigned to a particular zone.
Page 179 Correlations Software Zones Correlation of Input and Output Zones Input Devices Zones Output Devices SD350 CMF-300 SD350 CMF-300 ZONE MMF-300 CMF-300 MMF-302 CMF-300 CMF-300 MMF-302 CMF-300 CP350 ZONE CMF-300 CP300 SD350 CMF-300 SD350 ZONE SD350 CMF-300 MMF-302 The zone correlations which are shown graphically above are also presented in Table A.1 on page 180 and Table A.2 on page 181.
Page 180 Software Zones Correlations DETECTOR ZONE ASSIGNMENT Device Zone Device Zone Address ADJ/NOUN Address ADJ/NOUN Type Number Type Number SD350 FIRST HALL SD350 ELEV. LOBBY CP350 2ND FLOOR CP350 ROOM 210 SD350 3RD FLOOR SD350 MEZZANINE SD350 MECH. ROOM Table A.1 Detector Programming Sheet Example MS-9600LS Series Manual —...
Page 181 Correlations Software Zones MONITOR/CONTROL MODULE ZONE ASSIGNMENT Zone Device Zone Address Device Type ADJ/NOUN Address ADJ/NOUN Number Type Number MMF-300 MMF-302 1, 2 MMF-302 1, 2 MMF-302 CMF-300 CMF-300 CMF-300 CMF-300 CMF-300 1, 2, 3 CMF-300 CMF-300 CMF-300 CMF-300 Table A.2 Module Programming Sheet Example MS-9600LS Series Manual —...
Page 182 Software Zones Correlations DETECTOR ZONE ASSIGNMENT Device Zone Device Zone Address ADJ/NOUN Address ADJ/NOUN Type Number Type Number Table A.3 Blank Detector Programming Sheet - 1 of 2 MS-9600LS Series Manual — P/N 52646:B2 2/12/2010...
Page 183 Correlations Software Zones DETECTOR ZONE ASSIGNMENT Device Zone Device Zone Address ADJ/NOUN Address ADJ/NOUN Type Number Type Number Table A.4 Blank Detector Programming Sheet - 2 of 2 MS-9600LS Series Manual — P/N 52646:B2 2/12/2010...
Page 184 Software Zones Correlations MONITOR/CONTROL MODULE ZONE ASSIGNMENT Device Zone Device Zone Address ADJ/NOUN Address ADJ/NOUN Type Number Type Number Table A.5 Blank Module Programming Sheet - 1 of 2 MS-9600LS Series Manual — P/N 52646:B2 2/12/2010...
Page 185 Correlations Software Zones MONITOR/CONTROL MODULE ZONE ASSIGNMENT Device Zone Device Zone Address ADJ/NOUN Address ADJ/NOUN Type Number Type Number Table A.6 Blank Module Programming Sheet - 2 of 2 MS-9600LS Series Manual — P/N 52646:B2 2/12/2010...
Page 186: Appendix B: Default Programming
Appendix B: Default Programming The following table provides a list of the programming options and their factory default settings. Program Option Factory Default Program Option Factory Default Master Password 00000 NAC Enable Enabled Maintenance Password 11111 NAC Silenceable Detector Programming Not Installed NAC Type Bell...
Page 187: Appendix C: Nfpa Standard-Specific Requirements
Appendix C: NFPA Standard-Specific Requirements The FACP has been designed for use in commercial, industrial and institutional applications and meets the requirements for service under the National Fire Protection Association (NFPA) Standards outlined in this Appendix. The minimum system components required for compliance with the appropriate NFPA standard are listed below: Fire Alarm Control Panel Contains the main control board, cabinet (backbox and door), main power supply transformer and...
Page 188 NFPA Standard-Specific Requirements NFPA Signaling Systems for Central Station Service (Protected Premises Unit)/Remote Station The following figure illustrates an example of Central Station/Remote Station Reporting using a 411UDAC. The relay contacts from the FACP may be used to trip any dialer UL listed for Central Station/Remote Station Services.
Page 189 NFPA Standard-Specific Requirements The following figure illustrates an example of Central Station/Remote Station Reporting using a 411UD. The relay contacts from the FACP may be used to trip any dialer UL listed for Central Station/Remote Station Reporting Services. Note: The Monitor Module input, which is being used to monitor the 411UD Relay #2 Output (programmed for DACT Trouble), must be programmed as ‘Trouble’...
Page 190 NFPA Standard-Specific Requirements NFPA 72 Auxiliary Fire Alarm System All connections are power-limited and supervised. This application is not suitable for separate transmission of sprinkler supervisory or trouble conditions. Notes: 3 ohms maximum loop resistance allowed for wiring from control panel to Municipal Box. Cut JP6 on the FACP main circuit board to supervise placement of 4XTMF module and circuit.
Page 191 NFPA Standard-Specific Requirements NFPA 72 Remote Station Protective Signaling System Notes: Cut Jumper JP6 on the FACP main circuit board to supervise placement of the 4XTMF module. Refer to “4XTMF Transmitter Module Installation” on page 55 for detailed information. RS82 Remote Station Receiver UL listed. Refer to Fire•Lite Alarms, Inc., Instruction Manual for Remote Station Receiver Model RS82.
Page 192 NFPA Standard-Specific Requirements NFPA 72 Proprietary Protective Signaling Systems FACP Addressable Fire Control Panel FACP Main Board Form-C Alarm contact programmed to activate on General Alarm. Form-C Trouble contact which will automat- ically activate on any Trouble condition. Form-C relay contact programmed to activate on Supervisory condition.
Page 193: C.1: Central Station/Remote Station Transmitter: Connection To Facp Dry Contacts
Central Station/Remote Station Transmitter: Connection to FACP Dry Contacts NFPA Standard-Specific Requirements C.1 Central Station/Remote Station Transmitter: Connection to FACP Dry Contacts The dry contacts of the FACP programmable relays can be used to trip a UL-864 Listed Central Station/Remote Station Transmitter. The FACP contacts must be supervised by the Central Station/Remote Station Transmitter module using End-of-Line Resistors (ELRs) with a value determined by the Transmitter manufacturer.
Page 194: C.2: Mbt-1 Municipal Box Trip - Silenceable
NFPA Standard-Specific Requirements MBT-1 Municipal Box Trip - Silenceable C.2 MBT-1 Municipal Box Trip - Silenceable The following figure illustrates the connection of the MBT-1 (Municipal Box Trip) between the FACP and a Local Energy Municipal Box. The use of an addressable control module programmed for General Alarm and Silenceable allows silencing of the Municipal Box without resetting the panel or box.
Page 195: Appendix D: Facp With Keltron
Appendix D: FACP with Keltron The following figure illustrates the connections between the FACP and Keltron Receiver/Transmitter. CAUTION: POSSIBLE EQUIPMENT DAMAGE FOR REASONS OF WIRING DIAGRAM CLARITY, TERMINAL DESIGNATIONS OF KELTRON MODULES ARE NOT SHOWN IN ACTUAL ORDER. FOLLOW KELTRON MANUAL AND MODULE MARKINGS FOR EXACT TERMINAL LOCATIONS TO PREVENT SEVERE MODULE DAMAGE! IMPORTANT! All connections between the FACP and Keltron modules must be made within 20 feet and enclosed within conduit or equivalently protected against mechanical injury.
Page 196: Appendix E: Wire Requirements
Appendix E: Wire Requirements T-tapping of the SLC loop wiring is allowed for 2-wire (Style 4) configurations. The total resistance of any branch cannot exceed 40 ohms. The total wire length of all branches cannot exceed 10,000 feet (3,000 m). Connecting external system accessories to the FACP main circuits must be carefully considered to ensure proper operation.
Page 197: E.1: Nac Wiring
NAC Wiring Wire Requirements E.1 NAC Wiring The following table lists NAC wiring requirements for the FACP. CLASS-B CLASS-A Max. Max. allowable wire pair length Max. allowable wire pair length allowable NAC Load (feet) (feet) total loop (Amps) resistance AWG 12 AWG 14 AWG 16 AWG 18...
Page 198: Appendix F: Hvac Control
Appendix F: HVAC Control The FACP can be programmed to shut down a building’s HVAC fans in the event of a fire. The fans cannot be restarted until the fire alarm condition has been cleared and the FACP has been reset to a normal (non-alarm) condition.
Page 199: F.2.2: Hvac Ovrride
Monitor Module Operation HVAC Control F.2.2 HVAC OVRRIDE The HVAC OVRRIDE type code can be assigned to any addressable monitor module for the purpose of overriding or preventing the HVAC SHUTDN control modules from activating. The HVAC OVRRIDE monitor module acts globally throughout the FACP system and therefore is not programmed to a particular software zone.
Page 200: Appendix G: Canadian Application
Appendix G: Canadian Application • The MS-9600LSC is supplied with the DP-9692 Dress Panel. • When installing and programming the FACP, the Canadian Option must be set to ON prior to any other panel programming (refer to “Canadian Option” on page 113 of the Programming Section of this manual).
Page 201: Index
Index Numerics ANN-RLY Annunciator Module 36 ANN-SB80KIT Mounting Kit 28 300 Series addressable devices 20 annunciator 40 4XTMF module 190 ACM 14 coil resistance 55 ACM-8RF 14 current 55 graphic, see also LDM Series 14 installation 55 annunciator addressing 120 installation steps 56 annunciator, remote see also Transmitter Module 15...
Page 202 D–E Index Classic Loop Interface Protocol 100 Detector CLIP Mode add 67 see also Classic Loop Interface Protocol adding description 74 delete 68 Clock Format 104 edit 69 Coded Operation 157 enable/disable 71 Coding screen display 70 NAC 110 type 71 coding verification 72 two stage operation 111...
Page 203 Index F–N Maintenance 151 see also Indicators 17 FACP Supervisory 151 see also Fire Alarm Control Panel 13 Trouble 151 Features 13 LED annunciator 40 Fire Alarm Control Panel Local Energy Municipal Box Service 55 see also FACP 13 Local Programming 62 Form-C relay 19 Loop Setup 99 general alarm zone 84...
Page 204 O–P Index synchronized 157 Output Circuits 18 voltage drop 15 voltage, operating 15 wiring Style 47 PAS 72 NAC enable/disable 108 see also Positive Alarm Sequence 14 NAC options 100 PAS BYPASS 159 NAC type 109 PAS timer 105 NACKEY card 48 Password 15 N-ELR Mounting Plate 21 change 135...
Page 205 Index R–S program keys Reset 18 see also Key Panel 18 Resettable Power 18 Programming 61 current 47 autoprogramming 62 see also Smoke Detector Power 16 exiting 63 factory default 186 Level 1 63 Secondary Power Requirements 177 Level 2 63 sensitivity 157 manual 62 see also smoke detector sensitivity 157...
Page 206 T–Z Index Phone Line 2 169 measurements 164 Supervisory 154 ranges 164 SUPERVISORY AR 113 sync programming 108 Walktest 14 see also synchronization 112 audible 116 synchronization 157 Maintenance Level 142 by manufacturer 112 operation 160 programming 112 selection 84 see also strobe synchronization 14 silent 116 synchronized 157...
Page 207 Manufacturer Warranties and Limitation of Liability Manufacturer Warranties. Subject to the limitations set forth herein, Manufacturer warrants that the Products manufactured by it in its Northford, Connecticut facility and sold by it to its authorized Distributors shall be free, under normal use and service, from defects in material and workmanship for a period of thirty six months (36) months from the date of manufacture (effective Jan.
Page 208 World Headquarters 1 Firelite Place Northford, CT 06472-1653 USA 203-484-7161 fax 203-484-7118 www.firelite.com...

This manual is also suitable for:

Fire-lite alarms ms-9600lse Fire-lite alarms ms-9600udls Fire-lite alarms ms-9600udlse Fire-lite alarms ms-9600lsc

Honeywell FIre-LITe ALArms MS-9600LS Manual

Quick Links

Related Manuals for Honeywell FIre-LITe ALArms MS-9600LS

Summary of Contents for Honeywell FIre-LITe ALArms MS-9600LS

This manual is also suitable for:

Table of Contents