Honeywell Performance Series Quick Installation Manual page 2

Mounting and Aiming the Camera

1. Connect the camera's BNC connector to a coaxial cable.

2. Connect the camera's power connector to a 12 VDC/24 VAC power source.

3. Position the camera so that the screw holes on the base align with the anchors.

4. Fix the camera to the mounting surface using the

supplied screws.

5. Using the supplied hex key, loosen the locking screws

on the mounting bracket arm.

6. Point the camera in the desired direction by rotating

the camera body and mounting bracket arm.

7. Tighten the locking screws.

8. Refer to the following figure and table for external

cable functions.

1

2

3

4

5

CAUTION

The default resolution is 8MP in HQA. Use the OSD menu to change definition.

Configuring the Camera

1. Connect the camera to a Honeywell Performance Series HQA DVR and log on as the admin user.

2. Right-click to display the shortcut menu, then click Camera

Menu. The Menu Operation window opens.

3. Click Enter to display the camera's OSD menu.

4. To configure the camera, in the Menu Operation window,

click the up/down arrows to move through the menu list,

click the left/right arrows to change a menu setting, or click

Enter to enter a submenu ( ) or execute a command.

5. After you have finished configuring the camera, scroll down

to Exit, and then click Enter to exit the OSD menu. Right-click to close the Menu Operation window.

© 2018 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell. The information in this publication is believed to be accurate in all respects. However, Honeywell cannot assume responsibility for any consequences

resulting from the use thereof. The information contained herein is subject to change without notice. Revisions or new editions to this publication may be issued to incorporate such changes.

No.

Port Name

Function

Inputs DC 12V or AC 24 power. Please be sure to

1

DC 12V or AC

supply power as instructed in the Manual.

24V Power

Input

Device abnormity or damage could occur if power is

not supplied correctly.

2

Video Output

Connects to HRHT DVR to output video signal.

3

Audio Input

Connects to sound-pick-up devices to receive audio

signal.

4

Power Output

Supplies DC12V 2W power.

Dial switches to change output mode. Switch up

5

DIP Switch

indicates "ON", switch down indicates "OFF".

Switch2

Output Mode

Switch1

OFF

OFF

HQA

ON

ON

CVBS

ON

OFF

AHD

OFF

ON

TVI

Recommended Recorders

HRHT408*

HRHT416*

Regulatory Statements

FCC Compliance

Information to the User: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency

Locking screws

energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•

Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's

authority to operate the equipment.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la Classe B est conforme à la norme NMB-003 du Canada.

Manufacturer's Declaration of Conformance

Europe The manufacturer declares that the equipment supplied is compliant with the European Parliament and

Council Directive on the restriction of the use of certain hazardous substances in electrical and electronic equipment

(2011/65/EU), General Product Safety Directive (2001/95/EC), and the essential requirements of the EMC directive

(2014/30/EU), conforming to the requirements of standards EN 55032 for emissions, EN 50130-4 for immunity, and

EN 60950-1 for electrical equipment safety.

WEEE (Waste Electrical and Electronic Equipment)

Correct disposal of this product (applicable in the European Union and other European countries with

separate collection systems). This product should be disposed of, at the end of its useful life, as per applicable

local laws, regulations, and procedures.

2700 Blankenbaker Pkwy, Suite 150

Louisville, KY, 40299, USA

www.honeywell.com/security

+1 800 323 4576

(North America only)

8-channel, 2 SATA, 4 MP, HQA/1080p@120fps, HQA/SD/IP@120fps

16-channel, 2 SATA, 4 MP, HQA/1080p@240fps, HQA/SD/IP@120fps

Aston Fields Road, Whitehouse Industrial Estate

Runcorn, Cheshire, WA7 3DL, UK

www.honeywell.com/security/uk

+1 44 (0) 1928 754 028

(Europe only)

Document 800-23996V1 – Rev A – 04/2018

35F Tower A, City Center, 100 Zunyi Road

Shanghai, 200051, China

www.asia.security.honeywell.com

+86 21 221 96888

(Asia Pacific only)