Page 2: Warning
MorphoAccess® SIGMA Family Administrator Guide Introduction WARNING COPYRIGHT© 2016-2017All rights reserved. Information in this document is subject to change without notice and do not represent a commitment on the part of Morpho. No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying or recording, for any purpose without the express written permission of Morpho.
Page 3: Revision History
MorphoAccess® SIGMA Family Administrator Guide Revision History Revision History The table below contains the history of changes made to the present document. Version Date Description First version MorphoAccess® SIGMA Family Administration Guide Created from: April 2017 2014_0000002196_v11- MA SIGMA - Administration Guide 2015_2000010196_v8 - MorphoAccess®...
Page 4: Table Of Contents
MorphoAccess® SIGMA Family Administrator Guide Introduction Table of Contents WARNING ..........................2 REVISION HISTORY ....................... 3 SECTION 1 : INTRODUCTION ....................14 MorphoAccess® SIGMA Family Series Terminal..............15 Scope of the document ....................16 About Biometrics ......................18 About fingerprint biometrics ....................18 Templates supported ......................
Page 5 MorphoAccess® SIGMA Family Administrator Guide Introduction Date/Time settings ......................32 SSL Securing ......................... 32 Network Wi-Fi™ configuration .................... 33 MorphoAccess® Terminal Database Management ............34 General ..........................34 Adding a user to the database .................... 34 Removing a user from the database ................... 34 Database Size ........................
Page 6 MorphoAccess® SIGMA Family Administrator Guide Introduction Password Configuration ....................72 First Boot Assistance At Next Boot Configuration ............74 Recover Corrupted Components ..................76 SECTION 5 : MORPHOACCESS® TERMINAL ADMINISTRATION MENU ........77 Access to Administration Menu ..................78 User Menu ........................80 User Enrollment in Database ....................
Page 7 MorphoAccess® SIGMA Family Administrator Guide Introduction Terminal Settings > Communication > Communication Channels Configuration ..... 236 Additional User Verification Settings................. 240 Change LCD Password ....................... 243 Additional User Control Settings ..................245 USB Menu........................251 Format USB Mass Storage device ..................252 Initialize USB Mass Storage device ..................
Page 8 MorphoAccess® SIGMA Family Administrator Guide Introduction Communication Details ..................... 304 Steps to Setup Wallpaper ....................305 Recover Corrupted Components ..................306 Display Screens and Actions ..................307 SECTION 8 : TERMINAL CONFIGURATION THROUGH WEBSERVER ........311 Access to Administration Menu through Webserver ............312 Login to Webserver ......................
Page 9 MorphoAccess® SIGMA Family Administrator Guide Introduction Result of the access control request .................. 356 User’s Data required in the terminal ................. 356 Identification Modes (database extension licenses) ............356 Compatibility with Access Control Systems ............... 357 User Interface ........................358 SECTION 12 : ACCESS CONTROL BY AUTHENTICATION ............
Page 10 MorphoAccess® SIGMA Family Administrator Guide Introduction Biometric check and biometric data in local database ........... 375 Description ......................... 375 User’s data required in the terminal ................. 375 User’s data required on the user’s card ................375 Activation key ........................376 User interface ........................
Page 11 MorphoAccess® SIGMA Family Administrator Guide Introduction SECTION 13 : MULTIFACTOR ACCESS CONTROL MODE ............395 Multi-factor Mode ......................396 Description ......................... 396 User Interface ........................396 User’s data required in the terminal ................. 396 User’s data required on the user’s card ................396 Activation keys ........................
Page 12 MorphoAccess® SIGMA Family Administrator Guide Introduction SECTION 23 : MMI (MAN-MACHINE INTERFACE) CONFIGURATIONS ........449 MMI (Man-Machine Interface) Menu ................450 SECTION 24 : PROXY MODE ....................452 Presentation of Proxy (or slave) mode ................453 Process ..........................453 Local signals ........................454 Proxy mode use sample .....................
Page 13 MorphoAccess® SIGMA Family Administrator Guide Introduction Note about Terminal Clock Deviation ................475 SECTION 28 : TERMINAL USER INTERFACE ................. 476 Audio Man Machine Interface ..................477 Audible signal ........................477 Terminal States ........................478 Enrolment .......................... 481 LED – Buzzer Sequence ...................... 483 SECTION 29 : COMPATIBILITY ACCESSORIES, SOFTWARE LICENSES AND SOFTWARE APPLICATIONS........................
Page 14: Section 1 : Introduction
MorphoAccess® SIGMA Family Administrator Guide Introduction Section 1 : Introduction 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 15: Morphoaccess® Sigma Family Series Terminal
MorphoAccess® SIGMA Family Administrator Guide Introduction MorphoAccess® SIGMA Family Series Terminal Congratulations for choosing a MorphoAccess® SIGMA Family Series Automatic Fingerprint Recognition Terminal. MorphoAccess® SIGMA Family provides an innovative and effective solution for access control applications using Fingerprint identification. Amongst a range of alternative biometric technologies, the use of finger imaging has significant advantages, i.e., each finger constitutes an unalterable physical signature, developed before birth and preserved until death.
Page 16: Scope Of The Document
MorphoAccess® SIGMA Family Administrator Guide Introduction Scope of the document This document is intended to guide administrators on ‘How to setup and use’ the MorphoAccess® SIGMA Family Series terminal. It also talks about capabilities, and the possible configurations that can be done along with detailed steps and snapshots. On top of this an administrator can learn about access control processes, compatibility with access control systems, Time &...
Page 17 MorphoAccess® SIGMA Family Administrator Guide Introduction Contactless smartcard reader Terminal iCLASS® Terminal Name MIFARE® Outdoor Prox Series DESFire® iCLASS® ® NFC® MorphoAccess® SIGMA Lite iCLASS®   MorphoAccess® SIGMA Lite + iCLASS® MorphoAccess® SIGMA Lite Multi    MorphoAccess® SIGMA Lite + Multi MorphoAccess®...
Page 18: About Biometrics
MorphoAccess® SIGMA Family Administrator Guide Introduction About Biometrics About fingerprint biometrics Fingerprints are permanent and unique. They are formed before birth and last throughout one's life. Classification and systematic matching of fingerprints for different purposes have been in use since the late 19th century. The skin on the underside of fingers is different from the skin on other areas of a human body.
Page 19: Templates Supported
MorphoAccess® SIGMA Family Administrator Guide Introduction Templates supported Morpho terminals are able to manage external templates. Following is the list of supported templates. Morpho private fingerprint template formats PK_COMPV2, fingerprint template format (minutiae). PK_MAT, little endian fingerprint template format (minutiae). PK_LITE, fingerprint template format (minutiae).
Page 20: Notation
MorphoAccess® SIGMA Family Administrator Guide Introduction Notation Product support notation: In this document, the term “MorphoAccess® SIGMA Family terminal” is considered either “MorphoAccess® SIGMA” or “MorphoAccess® SIGMA Lite” or “MorphoAccess® SIGMA Extreme” Series terminal, unless it is explicitly mentioned. The term “MorphoAccess® SIGMA Lite”...
Page 21 MorphoAccess® SIGMA Family Administrator Guide Introduction Parameter description: In this document a parameter is described using this format: Parameter name Value Description For example to allow additional attempt for biometric authentication: Parameter name Value Description auth_param.additional_bio_c 1, 2 or 3 A value of “2”...
Page 22: Section 2 : Connecting The Terminal To A Pc
MorphoAccess® SIGMA Family Administrator Guide Connecting the Terminal to a PC Section 2 : Connecting the Terminal to a PC 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 23: General
MorphoAccess® SIGMA Family Administrator Guide Connecting the Terminal to a PC General Why would one connect the terminal to a PC? The MorphoAccess® SIGMA Family terminal is designed to be able to run in standalone mode, it means without any connection to a master system. But sometimes, a connection with a PC is useful to perform tasks like: ...
Page 24: Point To Point Ethernet Connection
MorphoAccess® SIGMA Family Administrator Guide Connecting the Terminal to a PC Point to Point Ethernet Connection The MorphoAccess® SIGMA Family terminal can be connected directly to a PC by an Ethernet cable. The administrator needs to consider the points mentioned below prior to connecting the terminal directly to a PC via an Ethernet cable.
Page 25: Connection Through Only One Ethernet Switch
MorphoAccess® SIGMA Family Administrator Guide Connecting the Terminal to a PC Connection through only one Ethernet switch The MorphoAccess® SIGMA Family terminal can be connected to a PC through an Ethernet switch. This is useful when no crossover cable is available, in that case the administrator can use one Ethernet switch and two Ethernet standard cables.
Page 26: Connection Through A Lan
MorphoAccess® SIGMA Family Administrator Guide Connecting the Terminal to a PC Connection through a LAN Description The administrator can also connect the MorphoAccess® SIGMA Family terminal to a PC via Local Area Network (LAN) by specifying a unique IP address or host name. The IP address could be static or dynamically assigned by the DHCP server in the network.
Page 27: Lan Without Dns Server
MorphoAccess® SIGMA Family Administrator Guide Connecting the Terminal to a PC It is useful to specify the MorphoAccess® SIGMA Family terminal by its host name, when the DHCP mode is enabled, as the IP address of the terminal can change after a power up. LAN without DNS Server This section helps the administrator in connecting the MorphoAccess®...
Page 28: Wi-Fi™ Network Configuration
MorphoAccess® SIGMA Family Administrator Guide Connecting the Terminal to a PC Wi-Fi™ Network configuration Requirements Wi-Fi™ connection is available under the following mandatory conditions:  The administrator must have plugged in a Morpho Wi-Fi™ USB adapter in the rear USB port of the terminal.
Page 29: Section 3 : Terminal Configuration And Administration
MorphoAccess® SIGMA Family Administrator Guide Terminal Configuration and Administration Section 3 : Terminal Configuration and Administration 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 30: Understanding Morphoaccess® Configuration
MorphoAccess® SIGMA Family Administrator Guide Terminal Configuration and Administration Understanding MorphoAccess® Configuration Presentation MorphoAccess® SIGMA Family terminal has factory default settings or reset values for all the supported functionalities. The administrator can configure the terminal depending on the desired level of security using one of the methods described below: Feature SIGMA Series SIGMA Lite Series...
Page 31: Configuring A Networked Morphoaccess
MorphoAccess® SIGMA Family Administrator Guide Terminal Configuration and Administration Configuring a Networked MorphoAccess® Introduction The administrator can manage a MorphoAccess® SIGMA Family terminal by a PC connected to the terminal, by using an application such as a web browser connected to the embedded Webserver (in MA5G mode) or MorphoBioToolbox (in case terminal is in MA5G or legacy Morpho modes).
Page 32: Network Factory Settings
MorphoAccess® SIGMA Family Administrator Guide Terminal Configuration and Administration Network factory settings By default the IP address of the MorphoAccess® SIGMA Family terminal is 192.168.1.10. The administrator can change IP address either by the local Administrator Menu or a distant system connected though an IP link or with a USB flash drive (USB Scripts).
Page 33: Network Wi-Fi™ Configuration
MorphoAccess® SIGMA Family Administrator Guide Terminal Configuration and Administration Network Wi-Fi™ configuration Administrator can configure Wi-Fi™ parameters, Wi-Fi™ connection is available under the following conditions:  The administrator has plugged in a Morpho Wi-Fi™ USB adapter. Details of the Installation procedure are described in the MorphoAccess® SIGMA Series Installation Guide or in the MorphoAccess®...
Page 34: Morphoaccess® Terminal Database Management
MorphoAccess® SIGMA Family Administrator Guide Terminal Configuration and Administration MorphoAccess® Terminal Database Management Database Management SIGMA Series SIGMA Lite Series SIGMA Extreme Series ✔ ✖ From administration menu of the terminal ✔ ✔ From Webserver Application General The administrator can manage the database of the MorphoAccess® SIGMA Family terminal by using administration menu of the terminal or through Webserver application connected to terminal.
Page 35: Database Size
MorphoAccess® SIGMA Family Administrator Guide Terminal Configuration and Administration Database Size The MorphoAccess® SIGMA Family terminal database storage is as follows: Database Limits SIGMA Series SIGMA Lite Series SIGMA Extreme Series Maximum User (Including 5000 Administrator) Maximum Authorized User 250,000 250,000 Maximum VIP User Transaction Log...
Page 36: Morphoaccess® Terminal License Management
MorphoAccess® SIGMA Family Administrator Guide Terminal Configuration and Administration MorphoAccess® Terminal License Management The administrator can install one or more licenses in the terminal in order to unlock one or several optional features of the MorphoAccess® SIGMA Family terminal. The MorphoAccess® SIGMA Family terminal supports the following license types: License type SIGMA Series SIGMA Extreme...
Page 37: User Licenses
MorphoAccess® SIGMA Family Administrator Guide Terminal Configuration and Administration User licenses Administrator can install user licenses for extending this maximum database limit. User data are stored with two fingers per user record. In case of duress finger is enabled, it can have three fingers per user record.
Page 38: Communication Licenses
MorphoAccess® SIGMA Family Administrator Guide Terminal Configuration and Administration Communication licenses MorphoAccess® SIGMA Family terminal supports communication to distant system through Ethernet Connection. There are other networks such as Wi-Fi™ and 3G which can be used for connecting terminal with distant systems. The administrator needs to install license(s) in order to enable the communication between the terminal and the distant system.
Page 39: Time And Attendance (T&A) License
MorphoAccess® SIGMA Family Administrator Guide Terminal Configuration and Administration Time and Attendance (T&A) license  MA_TA The administrator needs to install the MA_TA license in order to enable Time & Attendance (T&A) feature. Only if the license is loaded, an administrator can configure Time &...
Page 40 MorphoAccess® SIGMA Family Administrator Guide Terminal Configuration and Administration view the installed licenses or add licenses from a PC, an Ethernet or Wi-Fi™ connection and License Manager Application are needed. The application can be downloaded from our biometric terminals website (www.biometric-terminals.com). Screens &...
Page 41 MorphoAccess® SIGMA Family Administrator Guide Terminal Configuration and Administration Figure 8: Licenses installed in a MorphoAccess® SIGMA Family terminal 3. Refer to the screenshot above, the licenses on the MorphoAccess® SIGMA Family terminal are listed in the “license in hardware" line in the main window. For further information concerning the license management tool (License Manager PC tool), please see the document MorphoAccess®...
Page 42: Installing A New License
MorphoAccess® SIGMA Family Administrator Guide Terminal Configuration and Administration Installing a new license To install a new license, the administrator must follow the steps mentioned below:  Copy the received license file (.lic extension) on the PC  Launch the "License Manager" application then add the MorphoAccess® SIGMA Family terminal IP address as specified in the previous section.
Page 43: Terminal Firmware Upgrade
MorphoAccess® SIGMA Family Administrator Guide Terminal Configuration and Administration Terminal Firmware Upgrade How to get latest version of firmware The administrator can obtain the latest version of the MorphoAccess® SIGMA Family terminal firmware on a CD/ROM package from the customer service, or download it from Morpho Website dedicated to biometric terminals: http://www.biometric-terminals.com/ The administrator needs to have a login name and a password in order to access the protected...
Page 44 MorphoAccess® SIGMA Family Administrator Guide Terminal Configuration and Administration Syntax of the command-line [-h] [-v] -f path_to_file -e IP_address [-t timeout] [-p port_number] Options Description Displays the help menu. Verbose mode. This is optional. -f path Path to the binary file used for upgrade. This is mandatory. -e IP_address IP address of the terminal to upgrade.
Page 45: Morphoaccess® Sigma Family Modes
MorphoAccess® SIGMA Family Administrator Guide Terminal Configuration and Administration MorphoAccess® SIGMA Family Modes MorphoAccess® SIGMA Family (also referred to as MA5G) terminals are standalone biometric access control terminals that offer advance features for access rights of the users. MorphoAccess® SIGMA Family terminals are equipped with a facility to emulate (partially) either the previous generation of the MorphoAccess®...
Page 46 MorphoAccess® SIGMA Family Administrator Guide Terminal Configuration and Administration In case, users are enrolled in MA5G mode, the user data cannot be exported when terminal is configured in the L1 mode. There are certain other limitations, when MorphoAccess® SIGMA Family terminal is run in L1 Legacy mode. For details about these limitations, refer to MorphoAccess®...
Page 47: Morphoaccess® Sigma Family Native Mode
MorphoAccess® SIGMA Family Administrator Guide Terminal Configuration and Administration MorphoAccess® SIGMA Family native mode MorphoAccess® SIGMA Family terminal is by default in the native mode; this native mode is designed by MA5G, which means MorphoAccess® 5 generation. This mode supports new features and a remote management application called Webserver.
Page 48: Section 4 : Morphoaccess® Terminal First Boot Assistant
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal First Boot Assistant Section 4 : MorphoAccess® Terminal First Boot Assistant 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 49: Assistant Initialization
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal First Boot Assistant Assistant Initialization First Boot Assistant (FBA) is launched as soon as the MorphoAccess® SIGMA Family terminal is started for the first time. All the basic configurations can be done by following the simple and easy to follow menu on the FBA screen.
Page 50 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal First Boot Assistant 2. The administrator can configure the basic parameters via the First Boot Assistant Screen. For more details, please refer to the sections below: 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 51: Date & Time Configuration
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal First Boot Assistant Date & Time Configuration The administrator must configure the current date, time and time zone in the terminal, on the first boot or a reboot of the terminal. NOTE: The time stored in the product is not lost if power supply is removed for up to 48 hours. Access Path Access point Access Path...
Page 52 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal First Boot Assistant b. DD/MM/YYYY c. MMM-DD-YY d. DD-MMM-YY e. YYYY/MM/DD (this format is not available, if terminal is set in L1 mode) 4. Click on the Check button “ ” to save the setting 5.
Page 53 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal First Boot Assistant 10. Select Time Zone Configuration Figure 13: Configuring Time Zone 11. Select Observe Daylight Saving as ‘On’, in case the administrator needs to auto- schedule the time during the daylight saving months. By doing this, the terminal’s time is automatically set to an hour later than the actual time while in the daylight saving time frame.
Page 54 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal First Boot Assistant Figure 14: List of Predefined Time Zones of World 15. The list of Predefined Time Zones of the entire world is displayed 16. Scroll up or down to select required Time Zone from the list 17.
Page 55: Trigger Event
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal First Boot Assistant Trigger Event MorphoAccess® SIGMA Family terminal will begin checking for access rights upon the occurrence of a specific event on the terminal. By setting these configurations the administrator can define as to when the terminal would commence performing access checks. The administrator can chose from the following events.
Page 56 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal First Boot Assistant Figure 16: Selecting the event(s) that starts access control rights check process 1. The administrator can select from the above stated events. The event can be selected to be ON or OFF. 2.
Page 57: Language Configuration
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal First Boot Assistant Language Configuration The administrator can select the language of the terminal’s display by using this functionality. Multiple language options are available to select from, e.g. English, French, Spanish and Arabic. Access Path Access point Access Path...
Page 58 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal First Boot Assistant Press Language to select Figure 18: Language selection on main screen 1. On the Home Screen, the administrator can select from the language options such as Arabic, French, Spanish or English. Results The preferred language is saved.
Page 59: Show/Hide Language Icon
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal First Boot Assistant Show/Hide Language Icon The administrator can chose whether to display the language icon on the home screen or not. This can be done via the Web Server application. The value of this parameter (misc.language_config_display) can be 0 or 1.
Page 60: Ethernet Interface Settings
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal First Boot Assistant Ethernet Interface Settings The administrator can connect MorphoAccess® SIGMA Family terminal to other servers and door panels via Ethernet channel. Using Ethernet connection, the terminal can make access request to the access controller and receive result message. The administrator can configure the terminal to communicate through Ethernet channel by means of the FBA screen.
Page 61 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal First Boot Assistant Screens & Steps Figure 20: Selecting Ethernet-Network Configuration 1. Select Ethernet 2. Select IP Configuration Figure 21: Ethernet Configuration 3. Under Ethernet tab, the administrator can select IPV4 or IPV6 4.
Page 62 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal First Boot Assistant Figure 22: IP Mode Selection 5. An administrator can select IP Mode as ‘Static’ or ‘DHCP’ 6. Use Check button “ ” to save the setting Figure 23: Configuring IP Address under Static IP Mode The administrator can manually configure ‘IP Address’...
Page 63: Wi-Fi™ Configuration
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal First Boot Assistant Wi-Fi™ Configuration The administrator can connect MorphoAccess® SIGMA Family terminal to other servers and door panels via WLAN (Wi-Fi™ network). Using Wi-Fi™ connection, the terminal can make access request to the access controller and receive result message. The administrator can configure the terminal to communicate through WLAN by means of the FBA screen.
Page 64 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal First Boot Assistant Screens & Steps Automatic Configuration Figure 24: Selecting available Wi-Fi™ network 1. Select from the list of scanned Wi-Fi™ networks Figure 25: Enter Encryption Key 2. Enter an Encryption Key to connect to the selected Wi-Fi™ network 2017_2000025464-v03 This document and the information therein are the property of Morpho.
Page 65 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal First Boot Assistant Figure 26: Success message is displayed showing Wi-Fi™ network is configured Figure 27: Connected to Wi-Fi™ network Manual Configuration 1. Select WLAN Configuration to set up Wi-Fi™ Network 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 66 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal First Boot Assistant Figure 28: Selecting Other Network to set up Wi-Fi™ network manually 2. The list of available Wi-Fi™ networks will be displayed. Select Other Network to set up Wi-Fi™ network manually Figure 29: WLAN Parameter Configuration 3.
Page 67 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal First Boot Assistant Figure 31: Selecting Encryption Mode 5. The administrator needs to select the Encryption Mode, as supported by a Wi-Fi™ Router. In order to avoid unauthorized access, Encryption mode is selected. The available Encryption modes are: a.
Page 68 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal First Boot Assistant Figure 33: Entering in WLAN – IP Configuration 8. On WLAN screen select “IP Configuration” to set up the IP which is required to be connected through WLAN 9. Select IPV 4 or IPV 6 Figure 34: WLAN –...
Page 69 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal First Boot Assistant Figure 35: Success message is displayed showing Wi-Fi™ network is configured 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 70: Protocol Configuration
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal First Boot Assistant Protocol Configuration The administrator can configure the terminal to work in any of the following modes by using Protocol Configuration.  Legacy L1 i.e. Bioscrypt 4G Series Legacy Mode terminals ...
Page 71 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal First Boot Assistant Screens & Steps Figure 36: Protocol Configuration 1. Select Protocol from the list of modes 2. Click on the Check button “ ” to save the setting Results The protocol selected is saved. The administrator needs to reboot the terminal in order to use it in any of the legacy modes.
Page 72: Password Configuration
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal First Boot Assistant Password Configuration The administrator can use this function to reset the default login password of the terminal. The administrator can use this password to access the administration menu and perform required configurations.
Page 73 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal First Boot Assistant 1. Administrator needs to enter Current Password and use “ ” button to move on next screen. By default, the login password of the terminal is set as “12345” Figure 38: Entering New Password 2.
Page 74: First Boot Assistance At Next Boot Configuration
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal First Boot Assistant First Boot Assistance At Next Boot Configuration The configuration defined with the First Boot Assistant, can be either permanent or temporary. This is specified by the "First Boot Configuration Storage Type" parameter as described below: ...
Page 75 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal First Boot Assistant Results The preferred value of “First Boot Assistant At Next Boot” is saved. The terminal will display FBA menu, based on the value this parameter. 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 76: Recover Corrupted Components
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal First Boot Assistant Recover Corrupted Components There is a mechanism in the terminal to recover corrupted data such as Smartcard Keys, Terminal Password, SSL Certificate and User Database. This could have been corrupted in the event of a power failure or interrupt in ongoing operation.
Page 77: Section 5 : Morphoaccess® Terminal Administration Menu
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Section 5 : MorphoAccess® Terminal Administration Menu 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 78: Access To Administration Menu
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Access to Administration Menu The administrator can login to MorphoAccess® SIGMA Family terminal using a default password. The administration menu allows user to perform various actions and configurations on the terminal, through the categories of menu listed below. This section is about configurations that can be done via the terminal menu for MorphoAccess®...
Page 79 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 43: Logging in Device 1. Press on key lock icon Figure 44: Entering Password 2. Enter Password and Press on validation button NB Identification policy depends of misc.LCD_login_optionvalue : 0 - Password only (0 - Default) 1 - ID + Password 2 - ID + BIO + Password 3 - ID + BIO...
Page 80: User Menu
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu User Menu User menu offers all functions related to the end users. An administrator can use this to enroll new user in the system, edit user information, delete users from the terminal database, and reset user information from contactless smart cards.
Page 81: User Enrollment In Database
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu User Enrollment in Database By using this feature of MorphoAccess® SIGMA Family terminal, the administrator can enroll new users in the terminal. The user information such as name, biometric data (e.g. fingerprint), User ID and PIN, access rights, etc.
Page 82 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Screens & Steps Figure 47: Entering User Identifier 1. Enter User Identifier (User ID). Numeric value up to 24 digits. NOTE:  Wiegand protocol doesn't support special characters such as "*" and "#", then is not recommended to insert these characters in the User ID value.
Page 83 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 49: Enter First Name of User 4. First Name of user and Press on “ ” button to move to the next screen. 5. Similarly, on next screen, Enter Last Name of user and Press on “ ”...
Page 84 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 51: Select first finger to capture 8. Select finger for biometric data capture Figure 52: Biometric data capture 9. Place user’s finger on biometric Sensor. If finger is not placed properly or within the time limit, an error message is displayed.
Page 85 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 53: Set Duress Finger as ON 12. Once the administrator completes capturing fingerprints of the first and second finger, an option for capturing Duress Finger is enabled. 13. The administrator needs to select ON if it is required to capture duress finger. Follow steps 8 to 10, for enrolling duress finger Figure 54: Assigning Access Rights 14.
Page 86 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu c. Full Admin: The user is an administrator with full Admin Rights. He or she can access all the menus in the administration menu and perform operations. An administrator with full Admin Rights can enroll regular users, as well as administrators.
Page 87 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 55: Enter User PIN – Alphanumeric/Numeric 16. The administrator has to enter User PIN which can be either numeric or alphanumeric based the LCD_configuration.PIN_keypad_type. Default value of this parameter is 1 which enables Numeric keypad for User PIN.
Page 88 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu 2. When the Time and Attendance mode is enabled, entering job code during authentication is optional despite the Job Code Check being enabled. It is based on the value of parameter time_and_attendance.jobcode_by_key and selected time and attendance key during authentication.
Page 89 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu 21. The administrator can select an Access Schedule, if the access is to be allowed within a particular time period of the day. By default, the access schedule is selected as Schedule 63 which means access is allowed at any time of the day.
Page 90 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 60: Configuring Dynamic Message for User 25. Set Dynamic Message as On Figure 61: Setting duration for dynamic message 26. Select the duration for which the Dynamic Message is to be displayed on LCD screen by selecting the Start Date and End Date 27.
Page 91 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 62: Configuring Dynamic Message for User 28. The administrator can select the type of dynamic message as “Normal” or a “Picture Message” a. If Normal Message is selected, then on the next screen the message to be displayed, needs to be entered by the administrator.
Page 92 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 64: Enrolment Information Screen 31. The administrator can configure Infinite Expiry Date as OFF or ON. This parameter indicates whether user account is active for specific duration or will be active forever a.
Page 93 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 66: Defining User Rule – Trigger Source 36. Trigger Source: The administrator can configure which of the following triggers the terminal for the access. a. Set Biometric as ON, if the administrator wants to allow user to access by fingerprint identification.
Page 94 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 67: Defining User Rule – Record Reference Source 37. The administrator can configure whether user’s information should be looked up in the Terminal database and/or on the Smart Card using Record Reference Source a.
Page 95 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 69: Defining Control Mode - Face Detection Mode c. Face Detection Mode: The administrator can configure face authentication check rule as depicted in the snapshot above. Please refer to “Additional User Control Settings”...
Page 96 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Recommendation: In case of authentication failure due to bad biometrics, the administrator can re-enroll the user. In case of L1 mode, the re-enrolment can be done using Secure Admin station equipped with a MorphoSmart™ MSO biometric sensor only. 2017_2000025464-v03 This document and the information therein are the property of Morpho.
Page 97: User Enrolment In Card
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu User Enrolment in Card The administrator can encode a contactless smartcard for a user, using this functionality. The user's data are saved only on the card, and not in the terminal database. It means, that the authentication of the user is done by checking the user's data stored in the card.
Page 98 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Screens & Steps Figure 71: Select Card Data Format 1. The administrator can use the Card Data Format to select the data that will be used for user authentication. Following are the options available: a.
Page 99 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu c. ID Only: When the administrator selects this format, it implies that the user authentication is done by verifying the User ID d. ID + PIN + Template: When the administrator selects this format, it implies that the user authentication is done by verifying the User ID, PIN, and Biometric Template e.
Page 100: User Enrolment In Card & Database
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu User Enrolment in Card & Database An administrator can use this functionality to enroll a new user and store the user data in a contactless smartcard as well as in the database of the terminal. This implies that the authentication of the user is done by checking the details stored in the card as well as in terminal database.
Page 101 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 73: Select Card Data Format 1. The administrator can select the user data that is required for access rights check, by means of Card Data Format. The administrator must select the appropriate user data type and then encode the user’s card accordingly.
Page 102: Update User Information
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Update User Information The administrator can edit user information stored in database, by using this functionality. The administrator cannot update the user information if the user has been enrolled only in the card. However it is possible to erase and rewrite the user's card with new data.
Page 103 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 75: Entering first digits of the searched User ID 3. Enter the User ID of the user account which is required to be edited 4. Press on “ ” button to move to next screen Figure 76: Selecting User ID 5.
Page 104 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 77: Enrolment Information screen is displayed for editing 6. The administrator can update the following user details, by means of the Enrolment Information screen as depicted in the above snapshot. a.
Page 105: Authenticate User
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Authenticate User The administrator can authenticate user by using this functionality. This feature can be used by the administrator to test whether the enrolled user is allowed access or not. However the user can authenticate from the home screen, by entering in User ID and then placing finger when asked.
Page 106: Delete User
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 79: Entering User ID for authentication 1. Enter the User ID that is required to be authenticated and Press on “ ” button 2. Terminal will ask user to place finger on biometric sensor Results A success message is displayed and user will be granted access on successful authentication.
Page 107 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Screens & Steps Figure 80: Deleting User 1. If the administrator needs to delete a single user, Select Delete User. Figure 81: Searching User ID 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 108 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu 2. The administrator needs to enter the User ID that needs to be deleted. Figure 82: Deleting User ID 3. The list of User IDs matching entered User ID is displayed. Select a User ID 4.
Page 109 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Delete All User ID The administrator can use this functionality to delete all the users stored in terminal database. Access Path Access point Access Path SIGMA Series SIGMA Lite Series SIGMA Extreme Series Terminal User Menu >...
Page 110 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 85: Confirm All User Deletion 2. A confirmation message is displayed, asking the administrator to confirm the action 3. Press on check “ ” to confirm delete all users action 4.
Page 111: Card Manager
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Card Manager MorphoAccess® SIGMA Family terminals allows user enrolment and authentication using contactless smart cards. When the administrator enrolls a user on a smart card, the User Identifier, Fingerprint Template and PIN/BIOPIN are stored in the card. The terminal will now refer to the information on the card for user authentication if configured to do so.
Page 112 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Renewal of User Card A smart card has a default expiry date. Once the smart card has expired it is not useful for verification. The administrator can renew a contactless card that has expired with the same user data such as User ID, fingerprint, PIN and BIOPIN that is saved in it.
Page 113 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 87: Renewal of User Card 1. Select Renew User Card Figure 88: Select Card Data Format 2. Select the card data format from available options as below: a. ID + Template (fingerprint) b.
Page 114 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu 4. Select criteria to search user by ID, First Name or Last Name 5. Press on check button to move next Figure 90: Entering User ID to be searched 6. Enter the first characters of the selected search criteria. E.g. if search by User ID is selected, then enter User ID Prefix Figure 91: Selecting User ID 7.
Page 115 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 92: A success message is displayed showing user is stored in card Results User’s data stored in terminal database are copied on the card. The card is renewed with new expiry date.
Page 116 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Encode Administrator card When site key in a terminal is changed, it is required to load the same site key in all the terminals in a premises. In such scenario, an Administrator card can be used to change the site key in other terminals.
Page 117 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Screens & Steps Figure 93: Encoding Administrator card 1. Select Encode Administrator card Figure 94: Select Card Type to be encoded 2. Select the Card Type, for which site key is to be generated. Options are MIFARE® Classic, MIFARE®...
Page 118 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 95: Administrator card is encoded Results A success message is displayed showing that the administrator card is encoded. The site key in the terminal is copied in the administrator card. The administrator can change the site key of other terminals using same administrator card.
Page 119 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Encode Visitor Card Encoding means writing user data, which includes Name, Biometric data, PIN or BIOPIN; on contactless smart cards. Cards for normal users as well as visitors can be encoded. The administrator can encode a contactless card for a visitor by means of this functionality.
Page 120 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu 1. Select Encode Visitor Card Figure 97: User ID for Visitor Card 2. Terminal will prompt to enter User ID. NOTE: Contactless card CSN can also be used as User ID by configuring a specific parameter.
Page 121 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Smart Card Read Profile The administrator can set the type of card that MorphoAccess® SIGMA Family terminal will be able to read, by means of this functionality. This implies that these cards can be used for authentication purpose only.
Page 122 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 99: Smartcard Read Profile_Multi b. In case of iClass product. Figure 100: Smartcard Read Profile_iClass 2. The administrator must set the following card read profile as ON, if it is required to be readable by the terminal.
Page 123 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Smart Card Encode Profile The administrator can set the type of card that MorphoAccess® SIGMA Family terminal will be able to encode, by using this functionality. These cards can be used to store user’s profile and for user authentication.
Page 124 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 102: Smartcard Encode Profile 2. The administrator needs to set the following smartcards encode profile as ON, if they are to be encoded by the terminal: a. MIFARE® Classic b. MIFARE® Plus c.
Page 125 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Generate Site Key Securing card includes protecting the card by primary/secondary keys to prevent unauthorized use. At the time of authentication using a smart card, the site key stored in card and the one in the terminal must match.
Page 126 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 104: Generating Site Key 4. Enter the Passphrase to generate Site key using keyboard. 5. Use check button to save Figure 105: Success message is displayed showing site key is generated in the terminal 2017_2000025464-v03 This document and the information therein are the property of Morpho.
Page 127 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Reset Site Key The administrator can reset security keys stored in terminal to factory default settings by using this functionality. The administrator can select the card type from the available card types. Access Path Access point Access Path...
Page 128 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 107: Confirming reset key action 3. Confirm reset site key by click on “ ” Figure 108: Site Key is reset successfully 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 129 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Configure ELITE Mode The administrator can configure the iClass terminal in ELITE mode by using this functionality. The administrator can select the options to enable and/or disable the ELITE mode. When ELITE mode is enabled, the terminal will start accepting specific iCLASS card, ELITE card and starts rejecting the regular cards.
Page 130 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu 2. Select Present Configuration Card a. Terminal will ask to Place Card. b. Present the “Configuration card STD->Elite” Card c. Check that terminal display Hold Card and then Remove Card 3. Use “ ”...
Page 131 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu No. of Start Block for MIFARE® Cards The administrator can specify the location of the access control data on the contactless card, by configuring the number of the first block to read on the card. By default, the 1st block to read is block # 4.
Page 132 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Screens & Steps Figure 111: Setting No. of Start Block 1. Select Starting block number 2. On next screen the administrator can enter the start block number using keypad 3. Use “ ”...
Page 133 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Select Keyset for Reading MIFARE® Cards The administrator can select a key set that is used by terminal for authentication and reading MIFARE® cards, by means of this functionality. Following are the key set values that can be configured: ...
Page 134 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Select Enroll ID Format The administrator can set the User ID format to be encoded on card, by using this functionality. Access Path Access point Access Path SIGMA Series SIGMA Lite Series SIGMA Extreme Series...
Page 135 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 114: Selecting Enroll User ID Format 2. Select one of the following User ID formats: a. No CSN: this value indicates that the serial number on the contactless card will not be used as User ID.
Page 136 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu //reverse the first 4-bytes and reverse the next 4-bytes. //reverse the whole 8-byte after above manipulation //generate decimal from the manipulated HEX else //ICLASS CARD //reverse the first 4-bytes and reverse the next 4-bytes. //reverse the whole 8-byte after above manipulation //generate decimal from the manipulated HEX e.
Page 137 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Defining Application ID and File ID for DESFIRE® Cards The administrator can specify the value of the Application ID and File ID for reading DESFire® cards, by means of this functionality. When the DESFire® card is presented to the reader during authentication, the application ID is read from the configured location from where the active File ID is fetched which further contains the user data.
Page 138 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 115: Configuring Application ID and File ID 1. Select Application ID 2. Enter Application ID from range of 0x000001-0xFFFFFF. By default, application ID 0xEEE600 3. Now select File ID 4. Enter File ID using keypad, from range of 0 – 15. By default, File ID is set as 0 5.
Page 139 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Defining Offset for Reading iCLASS® Cards The administrator can configure the offset to read the data from 2APP iCLASS® cards, by using this functionality. When the iCLASS® card is presented to the reader, the application area 2 is read after the card is authenticated with the key 2.
Page 140 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 117: Set Key Offset 2. Enter Offset value. An administrator can configure offset from 0x13 to 0x9F (hex values) 3. Press on check “ ” button to save the Offset value 2017_2000025464-v03 This document and the information therein are the property of Morpho.
Page 141 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Defining Active Pages for Reading iCLASS® Cards The administrator can configure the active page for reading data from 16APP iCLASS® cards, by using this functionality. When the iCLASS® card is presented to the reader, the application area 2 is read after the card is authenticated with the key 2.
Page 142 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 119: Enter Active Pages 2. Enter number of Active Pages 3. Press on check “ ” button to save Defining ADF OID & DO TAG for HID iCLASS® SEOS® Cards The administrator can specify the value of ADF OID and DO TAG in the MorphoAccess®...
Page 143 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Screens & Steps Figure 120: Configure ADF OID & DO TAG for HID iCLASS® SEOS® cards 1. Select ADF OID Figure 121: Enter ADF OID 2. Enter ADF OID number 3. Press on check “ ”...
Page 144 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 122: Enter ADF OID 5. Enter DO TAG number 6. Press on check “ ” button to save Reset Card The administrator can reset a contactless card, by using this functionality. The user data stored in the card is erased.
Page 145 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Screens & Steps Figure 123: Reset card 1. Select Reset Card 2. Terminal will ask to Place Card at card reader. 3. Once the administrator places the card, terminal will read and reset the card by erasing the stored data.
Page 146: Multimedia Menu
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Multimedia menu The administrator can upload and manage audio, video and images on MorphoAccess® SIGMA Family terminal, by using the multimedia menu. These multimedia contents are used to perform various tasks such as to play an alarm when the terminal is tampered. The administrator needs to refer to the following sections in order to understand as to how one can upload the multimedia contents in the terminal and the supported formats.
Page 147: Audio Settings
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Audio Settings The administrator can configure the MorphoAccess® SIGMA Family Terminal to play a notification sound on the following events:  Access Denied: Audio is played when user verification has failed and access is denied ...
Page 148 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu  The maximum supported Audio file size is up to 500KB  Supported audio file formats are FLAC, PCM, and VORBIS  The administrator must ensure that the audio messages must be in the same language, as configured in the terminal Screens &...
Page 149 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu 6. A confirmation pop-up will appear. Press on “ ” icon to copy file from USB mass storage device to terminal Figure 128: Success message is displayed Results Success message is displayed showing Audio file is copied to terminal. Audio is played on respective action on terminal.
Page 150: Video Settings
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Video Settings MorphoAccess® SIGMA Family terminal is capable of playing video when screen is idle. The administrator can configure the following, by using Video settings:  Upload Video files using USB mass storage device ...
Page 151 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Screens & Steps Step 3 Step 2 Step 1 Figure 129: Uploading Video File in device 1. Select USB Mode 2. The administrator can view the folders present in USB mass storage device. 3.
Page 152 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 131: Success message is displayed Results Success message is displayed showing Video file is copied to terminal. The uploaded video is played on idle screen time out. The administrator can click on the “ ”...
Page 153: Images Settings
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Images Settings MorphoAccess® SIGMA Family terminal is capable of displaying images on the LCD screen. The images can be used for purposes listed below:  Dynamic Message: The administrator must set the “Dynamic Message Configuration” as ON at the time of user enrolment if it is required to display an image when the user is granted access.
Page 154 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Screens & Steps Step 3 Step 2 Step 1 Figure 132: Uploading Image File in device 1. Select USB mode 2. The administrator can view the folders present in USB mass storage device 3.
Page 155 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 134: Success message is displayed Figure 135: Image uploaded is displayed as wallpaper Results Success message is displayed showing image file is copied to terminal. The uploaded image is displayed as wallpaper or dynamic message. The administrator can select and Delete images using “...
Page 156: System Menu
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu System Menu The administrator can configure fundamental parameters of Terminal such as LCD screen parameters and transaction log settings, using the System menu. System menu also allows an administrator to launch the First Boot Assistant that has all basic parameters in one screen. Only an administrator with full administrative rights can access this menu.
Page 157: Terminal Configurations
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Terminal Configurations Set Factory Default The administrator can use this functionality for resetting all the parameters of MorphoAccess® SIGMA Family terminal to their default value. An administrator can also select particular parameters manually, for which values are needed to be reset as factory default value.
Page 158 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 138: Select Items to reset 2. The administrator can select parameters from the list and set as ON. The parameters that are marked ON, will be reset. 3. Press on check button to move next Figure 139: Confirmation message displayed 4.
Page 159 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Date and Time Configuration The administrator can set the time zone, current date and time in the MorphoAccess® SIGMA Family terminal, by means of this functionality. Besides this, there are options to set the format of date and time.
Page 160: Network Time Protocol Server (Ntp Server)
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Results Based on the selected time zone, the time and date will be calculated and set in the terminal. During Daylight Saving, the time will be auto-adjusted. Network Time Protocol Server (NTP Server) This functionality is used to synchronize the terminal date and time with external server using SNTP/NTP protocol, to update the terminal date and time automatically with the NTP server time.
Page 161 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Set Time Access Path Access point Access Path SIGMA Series SIGMA Lite Series SIGMA Extreme Series Terminal System Menu > Terminal Settings ✔ ✖ Menu > Date and Time Settings > Clock Parameters >...
Page 162 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Single Door Controller (SDC) Configuration The administrator can configure the Single Door Controller (SDC) parameters in order to control the access through a door when specific actions are triggered on MorphoAccess® SIGMA Family terminal.
Page 163 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu  Tamper Occurred: When Tamper Mode is enabled and if tamper gets triggered i.e. Physical movement of the terminal housing triggers a reed switch which in turn activates user specified Tamper options on the terminal. ...
Page 164 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Screens & Steps Figure 141: SDC Parameters configuration 1. Press on GPIO State to select modes Figure 142: Selecting GPIO State 2. By default “GPIO General Mode” is selected. In order to configure SDC on a terminal, select SDC Mode 3.
Page 165 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 143: Configuring Parameters in “SDC Mode” The administrator can select the following parameters when the SDC Mode is enabled. 4. Press on Door Unlock Time field to set the duration (in Seconds only) for which the door should be unlocked after access is granted.
Page 166 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Time Override Mode (TOM) Configuration The administrator can temporarily suspend the need for verification of a user for a specific time period, by using the Time Override Mode (TOM). Whenever TOM is triggered on terminal then door gets unlocked and user can open Door without any authentication till TOM remains active.
Page 167 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 145: Setting TOM Duration 2. Press on TOM Duration to set the duration for which door should be under TOM 3. Enter the number of minutes TOM will be active into the Time Override Duration field and use “...
Page 168 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Tamper Configuration for Terminal Security The MorphoAccess® SIGMA Family terminal can detect two types of intrusion attempts:  Someone tries to steal the complete terminal,  Someone tries to open the terminal The administrator can configure the Tamper parameters in order to take necessary actions on tampering of the terminal.
Page 169 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Screens & Steps Figure 146: Enabling Tamper 1. Press on Tamper State 2. In next screen, an administrator can set Tamper State as Disable or Enable 3. Select Enable and use “ ”...
Page 170 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu 6. Erase Template Database The administrator turns this as ON/OFF. When ON, all the templates enrolled and saved in the MorphoAccess® SIGMA Family terminal will be deleted on Tamper detection. 7. Play MMI The administrator can set this as ON if it is required to play a sound alarm on tamper detection.
Page 171 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu LCD Configuration The administrator can control the look and feel of the content/multimedia displayed on the LCD touch screen of MorphoAccess® SIGMA Family terminal’s LCD, by using this functionality. Several Parameters that an administrator can configure are: ...
Page 172 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Screens & Steps Screen Brightness Control Figure 148: LCD Brightness adjustment 1. Press on Brightness 2. On next screen an administrator can adjust the brightness of LCD back light by scrolling the curser left or right Scroll Figure 149: LCD Brightness adjustment...
Page 173 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Disable Sensor in Idle Mode The administrator can disable the biometric sensor backlight when terminal is in idle mode, by configuring this parameter. When turned ON, the biometric sensor will automatically power off, if the terminal is in idle mode.
Page 174 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Idle Screen Status The administrator sets this to be ON when it is desired that the terminal must be auto locked and a video needs to be played, incase no activity is detected on the terminal. The video to be played can be uploaded in the Idle Screen Video folder, using “Video Settings”...
Page 175 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Video Play Brightness Control Scroll Figure 152: Video Play Brightness Control 1. Press on Video Play Brightness 2. In the next screen, the administrator can adjust the brightness of the video by scrolling the curser left or right 3.
Page 176 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Idle Screen Time Out Figure 153: Configuring Idle Screen Timeout 1. Idle Screen Timeout parameter indicates that if there is no action taken on LCD for specified duration, then screen should be auto-locked and video play starts 2.
Page 177 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu 1. This parameter indicates whether the video needs to be played on idle screen for infinite duration or not. 2. Select OFF or ON 3. The administrator must define duration for which video is to be played, if the ‘Infinite video play’...
Page 178: Transaction Log
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Transaction Log The MorphoAccess® SIGMA Family terminal records each event taken place on a terminal. The events that can be logged are:  Access granted to the user  Access denied to the user ...
Page 179 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Configure Transaction Logging Mode The administrator can chose as to which event will be logged:  No Log: An administrator can set Transaction Logging to ‘No Log’ mode. This indicates that no actions will be recorded and stored on terminal ...
Page 180 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Results As per the selected mode of logging, transaction logs are created by terminal. In case terminal fails to store log parameter, an error message is displayed. 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 181 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Define Actions on Log Full Event The administrator can select the action to perform when there is no room for a new log record, by using this functionality:  Delete Partial Logs ...
Page 182 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu 2. Press on “ ” button to save settings Figure 158: Defining number of logs to be deleted 3. The administrator needs to define Number of Logs to be Deleted when delete action is triggered and Delete Partial Logs is set to be ON.
Page 183 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Delete Transaction Logs The administrator can delete all transaction logs recorded and stored in terminal database, by using this functionality. Access Path Access point Access Path SIGMA Series SIGMA Lite Series SIGMA Extreme Series Terminal...
Page 184: Miscellaneous Settings
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Miscellaneous Settings Global Device Volume The administrator can set volume of all the audio/video files that are uploaded in the terminal by using Global Terminal Volume. Access Path Access point Access Path SIGMA Series SIGMA Lite Series...
Page 185 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 161: Set Global Device Volume 2. Scroll the radio button to right side for increasing the volume and scroll towards left to decrease the volume 3. Press on check button to save settings Results Sound will be played as per the configured Global Terminal Volume.
Page 186 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Enable AZERTY Keyboard The administrator can enable AZERTY (French standard) keyboard type, by using this functionality. The default keyboard in MorphoAccess® SIGMA Family terminal is QWERTY (English standard keyboard). Access Path Access point Access Path SIGMA Series...
Page 187 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 163: AZERTY keypad 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 188: Web Server
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Web Server The administrator can access the Web Server. Web Server allows an administrator to configure any parameter of the terminal by connecting remotely. Please refer the “Access to Administration Menu through Webserver” in this document. By default the access to Web Server is disabled in a MorphoAccess®...
Page 189: Error Log Configuration
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Error Log Configuration MorphoAccess® SIGMA Family terminal is capable of capturing logs of the events when access is denied or any error has occurred during operations. The administrator can enable/disable error logging and configure related parameters, using ‘Error log Configuration’...
Page 190 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 166: Enable Error Logging 2. Select Error Log as ON, to enable error logging. Figure 167: Setting Error Log Debug Level 3. Select Debug Level from the available list a. Fatal b.
Page 191: Sensor Log Configuration
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu NOTE: If the administrator selects Debug Level as WARNING, then all the messages of the Error, Fatal, Alert and Critical category, will be logged. Messages in the ‘Notice’, ’Info’ , ‘Debug’ and ‘Trace’ category will not be displayed. 4.
Page 192 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 168: Select Error Log Configuration 1. Select Error Log Configuration Figure 169: Enable Error Logging 2. Select Sensor Log as ON, to enable sensor logging. Figure 170: Sensor Modules Log Activation 3.
Page 193: Communication Menu
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Communication menu MorphoAccess® SIGMA Family terminals are standalone terminals, it means the configuration and operations are performed without any connection to a host application. However, MorphoAccess® SIGMA Family Terminal is required to communicate with distant applications such as door controller, access controller or hosted application like Webserver.
Page 194: Security Recommendation
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Security recommendation It is recommended to disable unused communication channels to avoid security issues, however ensure to let at least one way to configure the terminal. Ethernet Network Configuration The MorphoAccess® SIGMA Family terminal can be connected to devices (such as central access controller, and door controller) via Ethernet.
Page 195 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu 6. Select IP Configuration Figure 173: Ethernet Configuration 7. Under Ethernet tab, the administrator can select IPV4 or IPV6 8. On next screen, default IP Mode is selected as static. Press on IP Mode for update Figure 174: IP Mode Selection 9.
Page 196: Wi-Fi™ Network Configuration
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 175: Configuring IP Address under Static IP Mode 11. The administrator can manually configure ‘IP Address’ of the terminal, ‘Subnet Mask’, 'Network Mask', 'Gateway Address' and 'DNS Servers under the Static IP Mode. Results Once the Ethernet Configuration is done, the terminal can be connected to a distant server.
Page 197 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu NOTE: The Administrator needs to contact mobile network provider for the settings for their network. Access Path Access point Access Path SIGMA Series SIGMA SIGMA Lite Extreme Series Series Terminal Communication Menu > Network ✔...
Page 198 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 177: Enter User Name 2. Enter User Name. Press on “ ” button to set. Figure 178: Enter Password / PIN 3. Enter Password / PIN. Press on “ ” button to set. 2017_2000025464-v03 This document and the information therein are the property of Morpho.
Page 199 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 179: Enter Access Number 4. Enter Access Number. Press on “ ” button to set. 5. Press on “ ” button to save all setting on Mobile Network parameter menu. 2017_2000025464-v03 This document and the information therein are the property of Morpho.
Page 200: Configure Hostname
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Configure Hostname The administrator can configure the Hostname when the IP Mode is selected as DHCP. The host name is used instead of the IP address, when a DNS (Domain Name Server) exists in the network.
Page 201: Serial Parameters
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Serial Parameters MorphoAccess® SIGMA Family terminal is able to communicate with external controller using Serial Port, through RS422 or RS485 protocols. When terminal is communicating (i.e. receiving inputs and sending outputs) through RS422, it will not be able to communicate through RS485, and vice versa.
Page 202 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 182: Select Baud Rate 2. The list of supported Baud Rates is displayed. Select the required Baud Rate 3. Use Check button “ ” to save Figure 183: Selecting Communication Type 4.
Page 203 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 184: Enter Net ID 6. Enter a Net ID (will be used to identify the terminal in a RS485 network connection) 7. Press on “ ” button to save 8. Use Check button “ ”...
Page 204: Security Menu
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Security Menu The administrator can configure security parameters to guard the MorphoAccess® SIGMA Family terminal against unauthorized access, by means of the Security Menu. Security menu deals with Biometric control, Network security, multi-user verification, LCD Login Password and User Control.
Page 205: User Control Settings
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu User Control Settings Configure Trigger Events The administrator can configure as to which of the following events trigger the MorphoAccess® SIGMA Family terminal. The terminal when triggered, begins the identification and authentication process.
Page 206 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Screens & Steps Figure 186: Configuring the events on which authentication/identification is triggered 1. Select the events listed in the trigger event screen (above) as ON or OFF 2. Use Check button “ ”...
Page 207 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Audio Settings” for more information about MMI configuration. Duress Finger Event is logged in transaction logs with action ‘Duress Finger detected’ on successful identification and action ‘VERIFY_DURESS_ID / VERIFY_DURESS_TEMPLATE’ on successful authentication. Refer to “How to Export & View Transaction Logs” section for more information on exporting and viewing transaction log.
Page 208 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Biometric Check Mode If the administrator sets this mode as ON, the biometric data of the finger placed on the sensor is compared with the corresponding one that is stored in the terminal database (identification) or in the card of the user (authentication).
Page 209 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Number of Biometric Check Attempt The administrator can configure the Biometric Matching Strategy by means of which multiple biometric check attempts are allowed to the user. This is to reduce the False Rejection Rate (FRR).
Page 210 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Access Path Access point Access Path SIGMA Series SIGMA Lite Series SIGMA Extreme Series Terminal Security Menu > User Control ✔ ✖ Menu Settings > Biometric Matching Strategy Webserver Terminal Settings > Biometric > ✔...
Page 211 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Biometric Timeout This parameter defines the duration within which the user needs to place finger on the biometric sensor of the terminal. If user fails to place the finger within that period, the access is rejected.
Page 212 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Screens & Steps Figure 190: Biometric Time Out 1. Enter the duration for Biometric Check Timeout. The entered duration is in terms of seconds 2. Use “ ” to save settings NOTE: Whatever the duration for Biometric Check Timeout, MALite will blink yellow 5 seconds after first unsuccessful biometric attempt before to come back to blue default light.
Page 213 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu PIN Check Mode At the time of enrolment, administrator can provide the PIN code along with the biometric data of the user. The administrator can enable PIN Check Mode if it is required to authenticate users based on the entered PIN.
Page 214 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Screens & Steps Figure 191: Setting PIN Check Mode 1. Set PIN Check Mode as OFF or ON. PIN Check Attempts The administrator can set this parameter, it indicates the maximum number of attempts a user can get before entering the correct PIN.
Page 215 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Screens & Steps Figure 192: Setting number of PIN Check Attempts 1. Select number of PIN Check Attempts as 1 or 2 2. Press on “ ” button to Save settings 2017_2000025464-v03 This document and the information therein are the property of Morpho.
Page 216 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu PIN Check Time Out The administrator can configure the PIN Check Time Out. This stands for the duration within which user is required to enter PIN. By default, the PIN Check Time Out is set as 5 seconds, the terminal will deny access, if user fails to enter PIN within the time limit.
Page 217 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu 2. Use “ ” to save settings Setting-up Matching Security Threshold The performances of a biometric system are mainly characterized by two values:  False Reject Rate (FRR): number of wrongly rejected authorized users, divided by the number of access requests, ...
Page 218 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Matching threshold values are detailed in the table below: Value Description Lowest threshold value: the number of false rejects is very low, but the number of false acceptances is too high for a secure usage. It is strongly advised not to use this value, because the terminal becomes too tolerant.
Page 219 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Access Path Access point Access Path SIGMA Series SIGMA Lite Series SIGMA Extreme Series Terminal Security Menu > User Control ✔ ✖ Menu Settings > Global Security Threshold ✔ ✔ Webserver Terminal Settings >...
Page 220: Anti-Tamper Switch For Terminal Security
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Anti-Tamper Switch For Terminal Security Description The MorphoAccess® SIGMA Family terminal is able to detect the opening of the box. This detection is controlled by the anti-tamper switch attached in the terminal. The opening of the external USB port cover is not detected.
Page 221 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Parameter Configuration The action(s) to be performed by the terminal on tamper detection is defined by several dedicated parameters: Parameter Name Parameter Value Description 0 or 1 Using this parameter, tamper detection can tamper.state be enabled or disabled.
Page 222 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Since the anti-tamper alarm message is sent via the same port/protocol as the access control result messages, the administrator must enable this function, otherwise the alarm message will not be sent (see section “Sending an Access Control Result Message”) Alarm Message Sent through Wiegand or Clock &...
Page 223 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Parameter Format Type Description Values wiegand_fmt_custom_slot5 Custom Wiegand format slot 5 wiegand_fmt_custom_slot6 Custom Wiegand format slot 6 wiegand_fmt_custom_slot7 Custom Wiegand format slot 7 Here, Custom Slot indicates the customer format defined for sending Wiegand String. Custom Format can only be set in parameter, if format is defined in corresponding slot.
Page 224: Network & Communication Security Settings
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Network & Communication Security Settings Authorized IP Configuration The administrator can use this feature to specify the IP address of the computers that are allowed to communicate with the terminal. Connection requests to the terminal will be rejected for the computers with an IP address not present in the list, despite having a compatible configuration application.
Page 225 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu 1. Select Authorized IP address Configuration Figure 196: Authorized IP addresses Mode selection 2. The administrator can set the Authorized IP Mode as ON or OFF. If this is set as OFF, then any IP address is allowed to connect and communicate with the terminal.
Page 226 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 198: Add IP address 3. The administrator can Add IP Address of the computer that can talk to the terminal. 4. Press on “ ” icon to save Figure 199: A success message is displayed showing IP Address is added successfully 2017_2000025464-v03 This document and the information therein are the property of Morpho.
Page 227 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Configure IP Addresses Range The administrator can add an IP Address Range, this is to authorize computers having IP addresses in the specified range to communicate with Morpho Access® terminal. None other than the specified range of computers can communicate with the terminal.
Page 228 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu View IP Address The administrator can view the IP Addresses that are added and authorized to communicate with the terminal, by using this functionality. Figure 201: Viewing authorized IP Addresses 1. Press on View IP Addresses. List of IP Addresses authorized is displayed View IP Range The administrator can view the Range of IP Addresses that are added and authorized to communicate with terminal, by using this functionality.
Page 229 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Delete IP Address The administrator can delete an IP Address, by using this functionality. It allows the administrator to select several IP addresses and delete them. Once deleted, that computer cannot communicate with the terminal. Figure 203: Deleting an IP Address 1.
Page 230 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Delete IP Address Range The administrator can delete an IP Address Range, by using this functionality. It allows an administrator to select several IP addresses range and delete them. Once deleted, computers having IP addresses in that range are not allowed to communicate with terminal.
Page 231 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu SSL Configuration Secure Sockets Layer (SSL) and its successor Transport Layer Security (TLS) are cryptographic protocol designed to provide communication security over Ethernet or Wi-Fi™ channels. These protocols are used to protect the communication between the MorphoAccess® SIGMA Family terminal and a distant system, such as a central access controller or a terminal configuration station.
Page 232 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Compatibility of cipher algorithms with SSL protocol versions Cipher Algorithm List Protocol Version sslv23 sslv3 tlsv1 tlsv1.1 tlsv1.2 AES128-SHA AES256-SHA AES128-SHA256 AES256-SHA256 AES128-GCM-SHA256 ECDHE-ECDSA-AES256-SHA:ECDH-ECDSA-AES256- ECDHE-ECDSA-AES128-GCM-SHA256:ECDH-ECDSA- AES128-GCM-SHA256 ECDHE-ECDSA-AES128-SHA256:ECDH-ECDSA- AES128-SHA256 ECDHE-ECDSA-AES128-SHA:ECDH-ECDSA-AES128- NOTE: Cipher algorithm that ends with ‘SHA256’ supports only SSL protocol version tls1.2. 2017_2000025464-v03 This document and the information therein are the property of Morpho.
Page 233 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu SSL Protocol Versions support for communication Client side (from PC application) sslv23 sslv3 tlsv1 tlsv11 tlsv12 sslv23 sslv3 tlsv1 tlsv11 tlsv12 The above table describes the protocol versions supported by the client side application, when communication is started by the terminal using a specific protocol.
Page 234 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Screens & Steps Figure 205: SSL Configuration 1. Select SSL Configuration 2. On next screen select Input Channel Figure 206: Configuring SSL Mode and parameters 3. Select SSL Mode as ON or OFF. Only if the SSL Mode is ON, the SSL protocol is used 2017_2000025464-v03 This document and the information therein are the property of Morpho.
Page 235 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 207: Entering Secure Communication Port 4. Enter Secure Communication Port: port that will be used for TLS or SSL protocol 5. Use “ ” button to save 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 236: Terminal Settings > Communication > Communication Channels Configuration
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Default Communication Port The administrator can define a default communication port that will be used for Ethernet connection, by using this functionality. Access Path Access point Access Path SIGMA Series SIGMA Lite Series SIGMA Extreme Series...
Page 237 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 209: Entering Communication Port 2. Enter Communication Port: port that will be used for TCP (plain text) 3. Use “ ” button to save Enabling TCP Channel Transmission Control Protocol (TCP) is a protocol that is used for transmission of the input/output messages between the MorphoAccess®...
Page 238 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Screens & Steps Figure 210: Configuring TCP Channels 1. The administrator needs to select the TCP Channel as ON if it is required to use TCP protocol for communication 2. Use “ ”...
Page 239 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Enabling Serial Channel Serial Channel is used for transmission of the input/output messages between the MorphoAccess® SIGMA Family terminal and distant systems, such as external controllers, connected through RS422 and RS485. By default, Serial Channel is disabled.
Page 240: Additional User Verification Settings
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Additional User Verification Settings When the administrator enables this feature, the terminal evaluates the access rights with the data of two different users, instead one user. It implies that, when access rights are based on the biometric data check, the terminal requires the fingerprint of two different users, to grant the access.
Page 241 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu 3. Use “ ” to Save Set Additional Users Verification Timeout The administrator can set this parameter to set the duration within which the additional user has to place finger on the biometric sensor. If the finger is not presented on the sensor within the time limit, access will be denied.
Page 242 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 214: Additional User Verification Timeout 2. Enter the Time limit 3. Use “ ” button to save 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 243: Change Lcd Password
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Change LCD Password An administrator can login to the terminal using an LCD Password. In order to prevent any unauthorized access, it is recommended to change the password periodically. The administrator can change the LCD password, by using this functionality.
Page 244 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 216: Entering New Password 2. Enter the New Password of choice 3. Use “ ” button to move on next screen Figure 217: Verifying New Password 4. Re-enter the New Password for verification 5.
Page 245: Additional User Control Settings
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Additional User Control Settings The MorphoAccess® SIGMA Family terminal administrator can set as to which access control parameters are applicable to allow access to the additional users, by using this functionality. Access Path Access point Access Path...
Page 246 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu 3. Door Open Schedule: This parameter indicates, whether terminal should check the door open schedule of the enrolled user 4. Authorized List Check Mode: At the time of enrolment the administrator can set whether the user is an authorized user or not.
Page 247 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu A parameter has been added in the “Complete Configuration” Screen of the Web Server named ucc.users_photo_policy, whose possible values can be 1, 2 or 3.  If the administrator sets this as 1, the images for only those users who have been granted access, shall be saved.
Page 248 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu ucc.users_ User Rule_Face Terminal_Face Successful Failed Failed Detection Detection Identification Identification Authentication photo_policy Face Detection Photo Taking Mandatory Face Detection Photo Taking Mandatory Face Detection Photo Taking Mandatory Face Detection Disable Optional Face Detection Disable...
Page 249 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu ucc.users_ User Rule_Face Terminal_Face Successful Failed Failed Detection Detection Identification Identification Authentication photo_policy Face Detection Face Detection Mandatory Optional Face Detection Face Detection Mandatory Optional Face Detection Face Detection Mandatory Optional Face Detection Face Detection Mandatory...
Page 250 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu References Refer to “Recommended Conditions for Face Detection” for knowing the correct position of the user and required lighting conditions in order to achieve correct face detection. 9. User Rule Check: This parameter defines the user rule check flow, whether to apply the user rules configured on terminal or on trigger event.
Page 251: Usb Menu
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu USB Menu MorphoAccess® SIGMA Family terminal is equipped with a USB Port that is to connect a USB Mass Storage, temporarily. Following are the uses of USB connection:  The administrator can upgrade firmware ...
Page 252: Format Usb Mass Storage Device
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Format USB Mass Storage device The administrator can use the Format USB Mass Storage device functionality to delete the entire data stored in a USB Mass Storage device. Once the device is formatted, it can be initialized to store the same folder structure as in the terminal.
Page 253 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 223: Confirmation message pop-up 3. A confirmation message pop-up is displayed, notifying that the previous data in the USB Mass Storage device will be lost. 4. Confirm action by using “ ”...
Page 254: Initialize Usb Mass Storage Device
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Initialize USB Mass Storage device The MorphoAccess® SIGMA Family terminal administrator must ensure that all the folders in the USB Mass Storage device have the same structure as on the terminal. This can be done using the Initialize USB Mass Storage device functionality.
Page 255 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 226: A confirmation message is displayed 3. Confirm Initialize USB Mass Storage device by using “ ” button Results A success message is displayed showing USB Mass Storage device is initialized. Now the administrator can use the USB Mass Storage device to upload or download data to or from the terminal.
Page 256: Import Data Into Terminal
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Import Data into Terminal MorphoAccess® SIGMA Family terminal is capable of importing several files in its local database. The administrator can import the following files to the terminal by using Import Data functionality: ...
Page 257: How To Import User Database
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu How to Import User Database Access Path Access point Access Path SIGMA Series SIGMA Lite Series SIGMA Extreme Series Terminal USB Menu > Import ✔ ✖ Menu Pre-requisite  USB Mass Storage device should be initialized and must have the user database file in the correct folder ...
Page 258 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 228: Selecting file to be imported in the terminal 2. The list of files present in the user database folder in USB Mass Storage device is displayed 3. Select a file to be imported Figure 229: Confirmation message to import User Database 4.
Page 259 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 230: Enter password 6. Enter a Passphrase. The passphrase set at the time of exporting user database is required to be entered for importing the same user database file in terminal. 7.
Page 260: How To Import Contectless Key
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu How to Import Contectless key Access Path Access point Access Path SIGMA Series SIGMA Lite Series SIGMA Extreme Series Terminal USB Menu > Import ✔ ✖ Menu Pre-requisite  USB Mass Storage device should be initialized and must have the contactless key file in the correct folder ...
Page 261 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 233: Selecting file to be imported in the terminal 2. The list of files present in the user database folder in USB Mass Storage device is displayed 3. Select a file to be imported Figure 234: Enter password 4.
Page 262: How To Import Language
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 235: Success message of contactless key imported is displayed Results Once the user’s site key is imported, the card can be edit, erase and renew. How to Import Language Access Path Access point Access Path SIGMA Series...
Page 263 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Screens & Steps Figure 236: Importing Language file 1. Select Language to be imported Figure 237: Selecting Language file to import 2. The language files present in USB Mass Storage device is displayed. The language file will be in ‘.qm’...
Page 264 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 238: Confirm import action 5. A confirmation message is displayed as a pop-up, select the check box to confirm import of language file. This action will replace the previous language file with the new file Figure 239: A success message is displayed showing language file is imported 2017_2000025464-v03...
Page 265: Export Data In Usb Mass Storage Device
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Export Data in USB Mass Storage Device The administrator can export the information from terminal database into the USB Mass Storage Device, by using this functionality. The terminal allows the export of the following categories of data.
Page 266: How To Export & View Transaction Logs
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu How to Export & View Transaction Logs Access Path Access point Access Path SIGMA Series SIGMA Lite Series SIGMA Extreme Series Terminal USB Menu > Export > Transaction ✔ ✖ Menu Logs Pre-requisites ...
Page 267 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 241: Selecting a file format for exporting transaction logs 2. Select the format in which data should be exported in, such as Binary Format or CSV Format NOTE: Only Transaction Log has option to be exported in .bin or .csv format. Error logs and User database is exported in encrypted format by default.
Page 268 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 243: A success message is displayed showing transaction log is exported Figure 244: Transaction Log in .CSV Format Sample Results The file for the exported transaction logs is created and stored in the USB Mass Storage Device, in .csv format.
Page 269: How To Export Error Logs
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu How to Export Error Logs Access Path Access point Access Path SIGMA Series SIGMA Lite Series SIGMA Extreme Series Terminal USB Menu > Export > Error Log ✔ ✖ Menu Pre-requisites ...
Page 270 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 246: A confirmation message pop-up 2. A confirmation message pop-up is displayed 3. Confirm an action to export log by using “ ” button Figure 247: A success message is displayed showing error log is exported Results The file for the exported error logs is created and stored in the USB Mass Storage Device, in .tar format.
Page 271: How To Export User Database
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu How to Export User Database Access Path Access point Access Path SIGMA Series SIGMA Lite Series SIGMA Extreme Series Terminal USB Menu > Export > User ✔ ✖ Menu Database Screens & Steps Figure 248: Exporting data into USB Mass Storage Device 1.
Page 272 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 249: A confirmation message pop-up 2. A confirmation message pop-up is displayed 3. Confirm an action to export database by pressing“ ” button Figure 250: Enter Passphrase 4. Enter Passphrase. The same passphrase will be required on importing the user database in terminal 5.
Page 273: How To Export Contectless Key
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Results The file for the user database is created in .BIN format and stored in the USB Mass Storage Device. The file is encrypted and non-readable, for security purpose. How to Export Contectless key Access Path Access point Access Path...
Page 274 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 253: Enter Passphrase 3. Enter Passphrase. The same passphrase will be required on importing the user contactless key in terminal 4. Press on “ ” button 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 275 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 254: A success message is displayed showing error log is exported Results The file for the contactless key is created in .BIN format and stored in the USB Mass Storage Device.
Page 276: Information Menu
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Information Menu The administrator can view important data such as the ones listed below, from a single panel. This can be achieved by means of the Information Menu.  Information related to Terminal’s commercial name and license ...
Page 277: View Device Details
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu View Device Details The administrator can view the information related to the MorphoAccess® SIGMA Family Terminal, by using this functionality. Access point Access Path SIGMA Series SIGMA Lite SIGMA Series Lite+ SIGMA Series Extreme Series...
Page 278 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu 1. Following information of the terminal are displayed: a. Device Commercial Name b. Device Description Name c. Device Serial Number d. Device Unique Product identifier e. License Name f. License Identifier g.
Page 279: View Firmware Information
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu View Firmware Information The administrator can view information regarding the current version of the Terminal firmware by using this functionality. The firmware version is upgradeable. Access point Access Path SIGMA Series SIGMA SIGMA Lite Series...
Page 280: View Sensor Revision Information
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu View Sensor Revision Information The administrator can view the information related to the biometric sensor, by using this functionality. Access point Access Path SIGMA Series SIGMA Lite Series SIGMA Extreme Series Terminal Information Menu...
Page 281: View Communication Parameters
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu View Communication Parameters The administrator can view the information of various Networks interface through which the terminal is connected with distant systems, Under Communication tab. Access point Access Path SIGMA Series SIGMA Lite Series SIGMA Extreme...
Page 282 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Figure 261: Viewing information of Ethernet network 2. Under Ethernet, select IPV4 or IPV6 3. Following information is displayed, of an IP connection: a. IP Mode i.e. Static or DHCP b. IP Address of the terminal c.
Page 283 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu a. IP Address of the terminal b. MAC Address of the terminal c. Subnet Mask d. Gateway Address e. Preferred DNS Address f. Alternate DNS Address Figure 263: Viewing Serial Protocol Configuration 5.
Page 284: View Memory Status
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu 6. Hostname of the terminal is displayed View Memory Status The administrator can view the remaining memory of the terminal, by using this functionality. Access point Access Path SIGMA Series SIGMA Lite Series SIGMA Extreme Series...
Page 285: View User Status
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu View User Status The administrator can view the summary of number of enrolled users, number of authorized listed users and number of VIP users by following the View User Status tab. Access point Access Path SIGMA Series...
Page 286 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu 5. Number of VIP users, the number of users enrolled as VIP users. Read more on “Access Control Process for VIP Users” 6. Maximum VIP user capacity indicates the maximum capacity of the users that can be enrolled as VIP users.
Page 287: View Transaction Log Status
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu View Transaction Log Status The administrator can view the Transaction log status, by following the access path mentioned below. It displays the number of current logs recorded in the terminal database as well as the maximum capacity of logs that can be stored in the terminal.
Page 288: Reboot Terminal
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu Reboot Terminal Reboot of Terminal is performed to restart the terminal (soft restart). Reboot is required in following scenarios:  On a firmware upgrade  Installation of Wi-Fi™ USB Adapter  When terminal legacy mode is changed to ‘Legacy L1’ or ‘Legacy Morpho’ or ‘MA5G’ ...
Page 289 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal Administration Menu screen by pressing “ ” button. By pressing button” “, the user can stay in the current screen to validate changes. Figure 269: Confirmation Message To Return to Home Screen 2017_2000025464-v03 This document and the information therein are the property of Morpho.
Page 290: Section 6 : Morphoaccess® Terminal : Videophone Facility
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal : Videophone Facility Section 6 : MorphoAccess® Terminal : Videophone Facility 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 291: Introduction To Videophone
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal : Videophone Facility Introduction to Videophone MorphoAccess® SIGMA Series terminal provides a Videophone feature which allows a user to initiate a video call by pressing an icon on the main screen of the terminal. This feature requires a Videophone server which is a PC with a VOIP client application using SIP protocol, such as Linphone.
Page 292: Configure Video Phone Server
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal : Videophone Facility Configure Video Phone Server In order to make a video phone call, it is a pre-requisite for the terminal to connect to computer based software, which can route the video call to the call center. Thus, the administrator needs to configure the server parameters, on which VoIP client application is installed.
Page 293 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal : Videophone Facility Figure 272: Enter Server Name 2. Enter Server Name 3. Use “ ” button to move to next screen Figure 273: Enter Server IP 4. Enter Server IP Address 5. Use “ ”...
Page 294 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal : Videophone Facility Figure 274: Entering Server Port 6. Enter Server Port 7. Use “ ” button to save Figure 275: Videophone Server is added successfully Results A success message is displayed showing video phone server is added successfully. Video call can be connected once server is configured.
Page 295: Viewing Video Phone Server Details
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal : Videophone Facility Viewing Video Phone Server Details The administrator can view parameters of the video phone server configured on MorphoAccess® SIGMA Family terminal, by using this feature. Access Path Access point Access Path SIGMA Series SIGMA Lite Series...
Page 296: Delete Video Phone Server
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal : Videophone Facility Delete Video Phone Server The administrator can delete registered videophone from the terminal, by using this functionality. Access Path Access point Access Path SIGMA Series SIGMA Lite Series SIGMA Extreme Series Terminal System Menu >...
Page 297 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal : Videophone Facility Figure 278: Video Server Deleted Success Message Results A success message is displayed on the screen showing video server is deleted. The record of the server is no longer available on the terminal NOTE: The videophone icon on idle screen shall not be displayed if the videophone feature is not configured.
Page 298: How User Can Make Video Call
MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal : Videophone Facility How User can make Video Call Videophone feature of MorphoAccess® SIGMA Family terminal enables end users to make a video call to a customer care center. The executive at customer care center can view the user and solve all functional queries on call.
Page 299 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal : Videophone Facility Figure 280: Select Server to make Video Call 2. The list of servers is displayed. Video call is connected to customer care center through these servers. 3. Select a Server Name 4.
Page 300 MorphoAccess® SIGMA Family Administrator Guide MorphoAccess® Terminal : Videophone Facility The user must press “ ” button and speak. The user must understand that this communication is one way in nature, hence when he speaks by enabling the microphone, he cannot hear the executive’s response. Figure 283: Release to hear In order to enable hearing, the user must release the same button from the terminal end.
Page 301: Section 7 : Terminal Menu For Morphoaccess® Sigma Lite+ Series
MorphoAccess® SIGMA Series - Administrator Guide Terminal Menu for MorphoAccess® SIGMA Lite+ Series Section 7 : Terminal Menu for MorphoAccess® SIGMA Lite+ Series 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 302: Morphoaccess® Sigma Lite+ Series Terminal Screens
MorphoAccess® SIGMA Series - Administrator Guide Terminal Menu for MorphoAccess® SIGMA Lite+ Series MorphoAccess® SIGMA Lite+ Series terminal Screens This section is about the screens displayed on MorphoAccess® SIGMA Lite+ Series terminals. Terminal Home Screen During the power up, the Morpho Logo and boot up animation will be displayed. Idle screen will display wallpaper, date and time with different icons.
Page 303: Terminal Details
MorphoAccess® SIGMA Series - Administrator Guide Terminal Menu for MorphoAccess® SIGMA Lite+ Series Figure 285: Information Menu Terminal Details The Terminal details will be displayed when “ ” icon is pressed. Figure 286: Terminal Details 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 304: Communication Details
MorphoAccess® SIGMA Series - Administrator Guide Terminal Menu for MorphoAccess® SIGMA Lite+ Series Communication Details The communication parameters and their default settings will be displayed when “ ” icon is pressed. Figure 287: Communication Details 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 305: Steps To Setup Wallpaper
MorphoAccess® SIGMA Series - Administrator Guide Terminal Menu for MorphoAccess® SIGMA Lite+ Series Steps to Setup Wallpaper On boot up, the MorphoAccess® SIGMA Lite+ Series home screen may either display the wallpaper (if set) or the default company logo. The wallpaper can be set by external commands. Following are the steps to set the wallpaper ...
Page 306: Recover Corrupted Components
MorphoAccess® SIGMA Series - Administrator Guide Terminal Menu for MorphoAccess® SIGMA Lite+ Series Recover Corrupted Components There is a system within the terminal to recover corrupted secure container components like Smartcard Keys, Terminal Password, SSL Certificate and User Database. Due to issues such as power failure or interrupt in operation, corruption may occur.
Page 307: Display Screens And Actions
MorphoAccess® SIGMA Series - Administrator Guide Terminal Menu for MorphoAccess® SIGMA Lite+ Series Display Screens and Actions The following table, enlists the various actions and indications on the MorphoAccess® SIGMA Lite+ Series terminal and the corresponding screen appearance. Display Screen Action/Indication Keypad Authentication Keypad Authentication for...
Page 308: V03 This Document And The Information Therein Are The Property Of Morpho. They Must Not
MorphoAccess® SIGMA Series - Administrator Guide Terminal Menu for MorphoAccess® SIGMA Lite+ Series Display Screen Action/Indication BIOPIN Entry Request Bootup Animation Screen (default) Please Wait…Action in Progress Tamper Detected Distant Session Is Opened Controller Feedback Animation with Door Open Configuration Failed for Device 2017_2000025464-v03 This document and the information therein are the property of Morpho.
Page 309: Be Copied Or Communicated To A Third Party Without The Prior Authorization Of Morpho July
MorphoAccess® SIGMA Series - Administrator Guide Terminal Menu for MorphoAccess® SIGMA Lite+ Series Display Screen Action/Indication Configuration Failed for Communication Place Card Remove Card Prompt for second attempt Admin Card Detected Firmware Upgrade Started Remove Finger 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 310 MorphoAccess® SIGMA Series - Administrator Guide Terminal Menu for MorphoAccess® SIGMA Lite+ Series Display Screen Action/Indication Invalid Input Time Override Mode – Active Sensor DB Upgrade Terminal Blocked 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 311: Section 8 : Terminal Configuration Through Webserver
MorphoAccess® SIGMA Series - Administrator Guide Terminal Configuration through Webserver Section 8 : Terminal Configuration through Webserver 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 312: Access To Administration Menu Through Webserver
MorphoAccess® SIGMA Series - Administrator Guide Terminal Configuration through Webserver Access to Administration Menu through Webserver The Webserver allows user to perform various actions and configurations on terminal, through below listed menus: Figure 290: Webserver Administration Menu  User Management Menu: For enrolling and managing users ...
Page 313 MorphoAccess® SIGMA Series - Administrator Guide Terminal Configuration through Webserver  Logs Menu: Used for retrieving transaction logs, configure transaction and debug logs  Schedules Menu: Used to add/edit/delete user defined Access Schedules, Holiday Schedules and Door Open Schedules  Control Configuration Menu: Used to configure the Controller (Panel) Feedback, User Control Parameters, Events and Contactless Card parameters ...
Page 314: Login To Webserver
MorphoAccess® SIGMA Series - Administrator Guide Terminal Configuration through Webserver Login to Webserver An administrator can login to MorphoAccess® SIGMA Family terminal through Webserver using the default password (Please refer to the section: Password Configuration). An administrator can enroll new user in the system, edit user information, delete users from the terminal database, and reset user information from contactless smart cards.
Page 315: User Enrollment In Database
MorphoAccess® SIGMA Series - Administrator Guide Terminal Configuration through Webserver User Enrollment in Database This feature of MorphoAccess® SIGMA Family Series terminal allows an administrator to enroll new users in the terminal. The user information such as name, biometric data (i.e. fingerprint), User ID and PIN, access rights, etc.
Page 316 MorphoAccess® SIGMA Series - Administrator Guide Terminal Configuration through Webserver a. Enter the First Name of user b. Similarly, Enter Last Name of user c. Select the Finger Id for First and Second Finger to enroll fingerprints of the user Figure 294: Enrolling Finger Index 3.
Page 317 MorphoAccess® SIGMA Series - Administrator Guide Terminal Configuration through Webserver 8. If the administrator wants to capture Duress Finger, the Total Fingers to enroll should be set as ‘3’ 9. Repeat steps 8 and 9 to enroll the duress finger. Figure 296: Enter User PIN 10.
Page 318 MorphoAccess® SIGMA Series - Administrator Guide Terminal Configuration through Webserver 12. Configure Observe Holiday Schedule by enabling or disabling. If this parameter is enabled, then access on holiday will be provided as per defined holiday schedule. If this parameter is disabled, then authentication is done without any check on holiday schedule.
Page 319 MorphoAccess® SIGMA Series - Administrator Guide Terminal Configuration through Webserver a. Set Finger Biometric as ON, if an administrator wants to allow user to access by fingerprint identification. If trigger event through biometric is OFF, then user cannot initiate the access rights check using fingerprint. And Biometric Check will be bypass for the particular user.
Page 320 MorphoAccess® SIGMA Series - Administrator Guide Terminal Configuration through Webserver 22. Allow Bio Substitution parameter can be set as ON. It indicates that instead of Biometric, the user can be authenticated through a substitute such as BIO-PIN or PIN 23. Press on Enroll User to Enroll the user with the details inputted. Results A confirmation message is displayed showing User is enrolled successfully.
Page 321: User Enrolment In Card
MorphoAccess® SIGMA Series - Administrator Guide Terminal Configuration through Webserver User Enrolment in Card The administrator can encode a contactless smartcard for a user, using this functionality. The user's data are saved only on the card, and not in the terminal database. It means, that the authentication of the user is done by checking the user's data stored in the card.
Page 322 MorphoAccess® SIGMA Series - Administrator Guide Terminal Configuration through Webserver f. ID + PIN: This format indicates that the user authentication is done by verifying the User ID, and PIN 2. According to the selected Card Data Format, next user’s data will be captured and stored in the card.
Page 323: User Enrolment In Card & Database
MorphoAccess® SIGMA Series - Administrator Guide Terminal Configuration through Webserver User Enrolment in Card & Database The administrator can enroll a new user and store the user data in contactless smartcard as well as in database of terminal. It means, that the authentication of the user is done by checking the details stored in the card as well as in terminal database.
Page 324 MorphoAccess® SIGMA Series - Administrator Guide Terminal Configuration through Webserver The user's data stored on card are not editable or viewable. Recommendation: In case of authentication failed due to bad biometric, the user can be re- enrolled. In case of L1 mode, the re-enrolment can be done using Secure Admin station equipped with a MorphoSmart™...
Page 325: Update User Information
MorphoAccess® SIGMA Series - Administrator Guide Terminal Configuration through Webserver Update User Information The administrator can edit the user information stored in database, using this functionality. It is not possible to edit the information of the user stored on the Card but it is possible to erase and rewrite the user's card with new data.
Page 326 MorphoAccess® SIGMA Series - Administrator Guide Terminal Configuration through Webserver Figure 304: Enrolment Information screen is displayed for editing 1. Enrolment Information screen is displayed. An administrator can update below information: a. First Name and Last Name of the user b.
Page 327: Delete User
MorphoAccess® SIGMA Series - Administrator Guide Terminal Configuration through Webserver Delete User Using this functionality, an administrator can delete user information. There are several options for deleting users:  Delete a User  Delete All Users Delete a User Access Path Webserver >...
Page 328 MorphoAccess® SIGMA Series - Administrator Guide Terminal Configuration through Webserver Screens & Steps Figure 306: Select Delete All Users action 1. Select Delete All Users to delete all the user in the database 2. A confirmation message is displayed, asking to confirm the action 3.
Page 329: Card Manager
MorphoAccess® SIGMA Series - Administrator Guide Terminal Configuration through Webserver Card Manager MorphoAccess® SIGMA Family terminals allows user enrolment and authentication using contactless smart cards. When a user is enrolled on smart card, the User Identifier, Fingerprint Template and PIN/BIOPIN are stored in the card. Terminal can check this information on card for authenticating a user.
Page 330 MorphoAccess® SIGMA Series - Administrator Guide Terminal Configuration through Webserver The card manager has certain parameters that are required to be configured, for required behavior of the system. These parameters are explained subsequently. Renewal of User Card A smart card has a default expiry date. Once the smart card is expired it is not useful for verification.
Page 331 MorphoAccess® SIGMA Series - Administrator Guide Terminal Configuration through Webserver 2. Click on user and Terminal will open a new window “Edit Type” 3. Select Card Only to Renew the Card 4. Now terminal open a new page to renew the card for the user 5.
Page 332 MorphoAccess® SIGMA Series - Administrator Guide Terminal Configuration through Webserver Smart Card Read Profile The administrator can set the type of card that MorphoAccess® SIGMA Family terminal will be able to read, using this functionality. It means these cards can be used for authentication purpose only.
Page 333 MorphoAccess® SIGMA Series - Administrator Guide Terminal Configuration through Webserver Smart Card Encode Profile The administrator can set the type of card that MorphoAccess® SIGMA Family terminal will be able to encode, using this functionality. It means these cards can be used to store user’s profile and used for user authentication.
Page 334 MorphoAccess® SIGMA Series - Administrator Guide Terminal Configuration through Webserver No. of Blocks and Start Block for MIFARE® Cards It is possible to define the location of the access control data on the contactless card, by specifying the number of the first block and total number of blocks to read on the card. By default, the 1st block to read is block # 4 and total number of blocks is #31.
Page 335 MorphoAccess® SIGMA Series - Administrator Guide Terminal Configuration through Webserver Select Keyset for Reading MIFARE® Cards The administrator can select a key set that is used by terminal for authentication and reading MIFARE® cards, using this functionality. The below key set values can be configured: ...
Page 336 MorphoAccess® SIGMA Series - Administrator Guide Terminal Configuration through Webserver Select Enroll ID Format The administrator can set the User ID format to be encoded on card, using this functionality. Access Path Webserver > Control Configuration > Contactless Card > General Parameters > Enroll User ID Screens &...
Page 337 MorphoAccess® SIGMA Series - Administrator Guide Terminal Configuration through Webserver Step 2: If (MIFARE) // 4 Byte CSN card //generate decimal from 4 Byte CSN. Else if (DESFire) // OR any 7 BYTE CSN card //Add 0 in beginning of CSN //reverse the first 4-bytes and reverse the next 4-bytes.
Page 338 MorphoAccess® SIGMA Series - Administrator Guide Terminal Configuration through Webserver Configure Partial CSN The administrator can set the value of start bit and length of bit i.e. total number of bit, to be used for Enroll and Verify, using this functionality. Access Path Webserver >...
Page 339 MorphoAccess® SIGMA Series - Administrator Guide Terminal Configuration through Webserver Defining Application ID and File ID for DESFIRE® Cards The administrator can specify the value of Application ID and File ID for reading DESFire® cards, using this functionality. When the DESFire® card is presented to the reader during authentication, the application ID is read from the configured location from where the active File ID is fetched which further contains the user data.
Page 340 MorphoAccess® SIGMA Series - Administrator Guide Terminal Configuration through Webserver Defining Offset for Reading iCLASS® Cards The administrator can configure the offset to read the data from 2APP iCLASS® cards, using this functionality. When the iCLASS® card is presented to the reader, the application area 2 is read after the card is authenticated with the key 2.
Page 341 MorphoAccess® SIGMA Series - Administrator Guide Terminal Configuration through Webserver Defining Active Pages for Reading iCLASS® Cards The administrator can configure the active page for reading data from 16APP iCLASS® cards, using this functionality. When the iCLASS® card is presented to the reader, the application area 2 is read after the card is authenticated with the key 2.
Page 342 MorphoAccess® SIGMA Series - Administrator Guide Terminal Configuration through Webserver Reset Card The administrator can reset a contactless card. The user data stored in the card is erased, using this functionality. Terminal will also overwrite the current site key on the card with default. Access Path Webserver >...
Page 343: Section 9 : Usb Scripts
MorphoAccess® SIGMA Series - Administrator Guide USB Scripts Section 9 : USB Scripts 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 344: Usb Scripts
MorphoAccess® SIGMA Series - Administrator Guide USB Scripts USB Scripts MorphoAccess® SIGMA Family terminal can be configured using encrypted USB scripts. These scripts can be created from MorphoBioToolbox. When user connects the USB drive which contains the USB scripts to the terminal, the intended operations will be performed and corresponding results will be written into the USB drive.
Page 345: Access Control
MorphoAccess® SIGMA Series - Administrator Guide Access Control Section 10 : Access Control 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 346: Access Control Presentation
MorphoAccess® SIGMA Series - Administrator Guide Access Control Access control presentation Typical architecture of an access control system Typical access control system architecture includes:  One MorphoAccess® terminal per area for access control.  A user management or administration menu. ...
Page 347: Typical Access Control Process
MorphoAccess® SIGMA Series - Administrator Guide Access Control Typical access control process 1. The administrator must enroll all the authorized users. This means that a record is created for each user, containing a unique identifier and biometric data for two of his fingers.
Page 348: Preliminary: Adding A Biometric Template In Local Database
MorphoAccess® SIGMA Series - Administrator Guide Access Control Preliminary: adding a biometric template in local database Access point Access Path SIGMA Series SIGMA Lite Series SIGMA Extreme Series ✔ ✖ User Menu Terminal Menu > User Menu ✔ ✔ User Webserver >...
Page 349: Morphoaccess® Sigma Family Terminal Operating Modes
MorphoAccess® SIGMA Series - Administrator Guide Access Control MorphoAccess® SIGMA Family terminal operating modes Standalone mode or Slave mode Modes of Operation SIGMA Series SIGMA Lite Series SIGMA Extreme Series ✔ ✔ Standalone Mode ✔ ✔ Slave Mode/Proxy Mode The MorphoAccess® SIGMA Family terminal supports two exclusive operating modes: ...
Page 350: Access Control Process In Identification Mode
MorphoAccess® SIGMA Series - Administrator Guide Access Control Access Control Process in Identification Mode Figure 320: Access Control Flow Diagram when Terminal is in Identification Mode 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 351: Access Control Process In Authentication Mode
MorphoAccess® SIGMA Series - Administrator Guide Access Control Access Control Process in Authentication Mode 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 352: Access Control Process For Vip Users
MorphoAccess® SIGMA Series - Administrator Guide Access Control Figure 321: Access Control Flow Diagram in Authentication Mode Note: Face detection applies only for MorphoAccess® SIGMA and SIGMA Extreme Series terminal. Access Control Process for VIP Users If the administrator lists a user as VIP, the access control flow for that user will differ from the general access control flow.
Page 353: Access Control Result
MorphoAccess® SIGMA Series - Administrator Guide Access Control Access Control Result Information for the User The MorphoAccess® SIGMA Family terminal communicates the result of the access right check by a local audible and visible signal. These signals are described in the “Audio Man Machine Interface”...
Page 354: Access Granted
MorphoAccess® SIGMA Series - Administrator Guide Access Control Access Granted Figure 322: Access Granted Diagram for MorphoAccess® SIGMA Family Access Denied Figure 323: Access Denied diagram for MorphoAccess® SIGMA Family 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 355: Section 11 : Access Control By Identification
MorphoAccess® SIGMA Series - Administrator Guide Access Control by Identification Section 11 : Access Control by Identification 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 356: Identification Mode Description
MorphoAccess® SIGMA Series - Administrator Guide Access Control by Identification Identification Mode Description Identification Process The identification process consists in retrieving the identity of an unknown person, by comparing the data (presented by the unknown person) with a database that contains similar type of personal data of known persons.
Page 357: Compatibility With Access Control Systems
MorphoAccess® SIGMA Series - Administrator Guide Access Control by Identification biometric data of two fingers per user record is stored. The maximum database capacity can be extended by installing specific licenses. For more details on supported licenses, please refer to “Terminal License Management”...
Page 358: User Interface
MorphoAccess® SIGMA Series - Administrator Guide Access Control by Identification User Interface In this mode, the MorphoAccess® SIGMA Family terminal waits for the placement of a finger on the biometric sensor. This state is displayed to the user by a specific signal, as described in “Terminal States”...
Page 359: Section 12 : Access Control By Authentication
MorphoAccess® SIGMA Series - Administrator Guide Access Control by Authentication Section 12 : Access Control by Authentication 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 360: Authentication Process
MorphoAccess® SIGMA Series - Administrator Guide Access Control by Authentication Authentication Process Introduction The MorphoAccess® SIGMA Family terminal offers an authentication mode designed to work with contactless smart cards. These contactless smart cards are used as personal cards. Then this section relates only to terminals equipped with a contactless smartcard reader (see section Scope of the document).
Page 361: Contactless Smart Card
MorphoAccess® SIGMA Series - Administrator Guide Access Control by Authentication The user’s card must contain the user’s identifier and optionally his biometric data. The terminal performs the required identity checks using the data read on the user’s card, and if required, data stored in the internal database. When the ‘biometric check’...
Page 362 MorphoAccess® SIGMA Series - Administrator Guide Access Control by Authentication iCLASS SE® Card HID MODELS Morpho readers Standard for contactless card description PVC Techn Composite MA SIGMA communications ology Technology MA SIGMA Lite 3000 3050 2k bit (256 Bytes) card ISO 15693/14443B Limited support * 16k bit (2k Bytes) card with...
Page 363: Authentication Process Options
MorphoAccess® SIGMA Series - Administrator Guide Access Control by Authentication Authentication Process Options The MorphoAccess® SIGMA Family terminal offers several authentication methods depending on the reference biometric data location of a user and the level of security required. The user’s reference biometric data can be located: ...
Page 364 MorphoAccess® SIGMA Series - Administrator Guide Access Control by Authentication Because of above change in access rule workflow, to achieve L1 use case of disabling BIO check for certain user, follow below procedure  Disable the terminal biometric check  Enable BIO check in user rule for all the users ...
Page 365: Automatic Bypass Of Biometric Control
MorphoAccess® SIGMA Series - Administrator Guide Access Control by Authentication Automatic bypass of biometric control The MorphoAccess® SIGMA Family terminal offers an authentication mode which depends on the content of the user’s ‘card’. The terminal searches the user card for data to ascertain if biometric control is mandatory or not.
Page 366: Selection Of User's Contactless Card Type (Mifare® And/Or Desfire®)
MorphoAccess® SIGMA Series - Administrator Guide Access Control by Authentication Selection of user’s contactless card type (MIFARE® and/or DESFire®) Contactless Card type Since the MorphoAccess® SIGMA Family terminals are equipped with a contactless smartcard reader that is compatible with MIFARE® and DESFire® cards, the administrator can specify the type of card to be supported by the terminal..
Page 367 MorphoAccess® SIGMA Series - Administrator Guide Access Control by Authentication Compatibility with “Authentication” modes Using a binary value read on the card as user’s identifier is allowed only with MIFARE® smart cards, and when the “sc.encode_profile” configuration key is set to 0 (zero). All other values of this configuration keys requires TLV formatted data, as described in the MorphoAccess®...
Page 368: Biometric Check, Biometric Data On User's Card
MorphoAccess® SIGMA Series - Administrator Guide Access Control by Authentication Biometric check, biometric data on user's card Description In this mode, each user's card contains an identifier and the biometric data of two different fingers of the user. The terminal compares the biometric data of the finger placed on the biometric sensor, with the reference biometric data of the two user's fingers read on the card.
Page 369: User Interface
MorphoAccess® SIGMA Series - Administrator Guide Access Control by Authentication User Interface The authentication process starts when the user presents his contactless card in front of the terminal (where the antenna of the contactless card reader is located). If it is compatible (same authentication keys, and mandatory data present on card), the user will be invited to place his finger on the biometric sensor, for biometric authentication.
Page 370: Pin Verification - Pin Stored On Card
MorphoAccess® SIGMA Series - Administrator Guide Access Control by Authentication PIN verification - PIN stored on card Description In this mode, each user's card contains a User ID, unique PIN Code and the biometric data of two different fingers of the user. The terminal detects the user by means of the User ID on his ‘card’.
Page 371: Activation Key
MorphoAccess® SIGMA Series - Administrator Guide Access Control by Authentication Activation key  The administrator must select a ‘card’ type that can accommodate at least “User ID + PIN” or “User ID + Biometric + PIN”. This needs to be done at user enrolment time. ...
Page 372: User Interface
MorphoAccess® SIGMA Series - Administrator Guide Access Control by Authentication User Interface The authentication process starts when the user presents his contactless card in front of the terminal (where the antenna of the contactless card reader is located). If it is compatible (same authentication keys, and mandatory data present on card), the user is invited to enter the PIN, for PIN Verification.
Page 373: Biopin Verification - Biopin Stored On Card
MorphoAccess® SIGMA Series - Administrator Guide Access Control by Authentication BIOPIN verification - BIOPIN stored on card Description In this mode the card should contain a Biometric PIN (BIOPIN). The goal of this mode is to substitute fingerprint based authentication by BIOPIN based authentication. This is useful when the fingerprints of the user are not available during enrolment for some reason.
Page 374: User Interface
MorphoAccess® SIGMA Series - Administrator Guide Access Control by Authentication  The administrator needs to correctly configure the User Record Reference parameter value to enable authentication using smart card, from the Terminal Menu or Webserver application. Please refer to “User Enrolment in Database”...
Page 375: Biometric Check And Biometric Data In Local Database
MorphoAccess® SIGMA Series - Administrator Guide Access Control by Authentication Biometric check and biometric data in local database Description In this mode, only the User ID is read from the card. The biometric data of two fingers of the user are stored in the internal database, with the same User ID as the one on the user’s card. The terminal compares the biometric data of the finger placed on the biometric sensor, with the user’s biometric data found in the database (in user's record).
Page 376: Activation Key
MorphoAccess® SIGMA Series - Administrator Guide Access Control by Authentication Activation key  The administrator must select a Card Type that can accommodate User ID.  The Trigger event corresponding to ‘Card’ must be set to ON  The administrator needs to configure the User Record Reference parameter value to Card for authentication using terminal database, by using Terminal Menu or Webserver.
Page 377: Authentication With Local Database: User Id Entered From Keyboard
MorphoAccess® SIGMA Series - Administrator Guide Access Control by Authentication Authentication with local database: User ID entered from keyboard Description In this mode, the User ID is entered using the MorphoAccess® SIGMA Family terminal keyboard. If the User ID exists in the database, the terminal performs an authentication using the biometric templates associated to this User ID.
Page 378: Authentication With Local Database: Id Input From Wiegand Or Clock & Data
MorphoAccess® SIGMA Series - Administrator Guide Access Control by Authentication Authentication with local database: ID input from Wiegand or Clock & Data Description This mode requires an external card reader that will send the User ID to authenticate to the MorphoAccess®...
Page 379 MorphoAccess® SIGMA Series - Administrator Guide Access Control by Authentication Parameter name Value Description  Set ‘0’ to never send data using Wiegand Port  Set ‘1’ to always send data using Wiegand Port (default)  Set ‘2’ to send data only when verification is initiated from Wiegand source wiegand.external_port_output_type...
Page 380: Wiegand Frame Configuration
MorphoAccess® SIGMA Series - Administrator Guide Access Control by Authentication Wiegand Frame Configuration When set up to communicate with Wiegand protocol, the MorphoAccess® SIGMA Family terminal can handle several data formats for reading Wiegand string; refer to “Wiegand Format and Associated Values”. The default format of Wiegand string is Standard 26 Bits.
Page 381: Site-Code Propagation
MorphoAccess® SIGMA Series - Administrator Guide Access Control by Authentication Site-code Propagation Site code propagation allows the usage of site code received from Wiegand input frame and apply same output Wiegand frame. Configuration “wiegand.site_code_propagation” is used to enable site code propagation 0 - Disable site code propagation (Default) 1 - Enable site code propagation Site code is stored each time, authentication happens.
Page 382: No Biometric Check, No User Id Check
MorphoAccess® SIGMA Series - Administrator Guide Access Control by Authentication No biometric check, no User ID check Description This authentication mode is a version of the “Biometric check, biometric data on user's card” authentication mode, such that the biometric check is disabled. When the administrator enables this mode, the terminal searches only for the User ID on the user’s card.
Page 383: Activation Key
MorphoAccess® SIGMA Series - Administrator Guide Access Control by Authentication Activation key  The administrator needs to select the Card Type, such that it can accommodate User ID. This must be ensured at the time of user enrolment.  The administrator needs to correctly configure the User Record Reference parameter by using Terminal Menu or Webserver.
Page 384: No Biometric Check, User Identifier In The Database
MorphoAccess® SIGMA Series - Administrator Guide Access Control by Authentication No biometric check, User Identifier in the database Description This authentication mode is the version of the “Biometric check and biometric data in local database” authentication mode, when biometric check is disabled. The user’s identifier is the only data read on user’s card.
Page 385: Activation Key
MorphoAccess® SIGMA Series - Administrator Guide Access Control by Authentication Activation key  The administrator needs to select Card Type at the time of User Enrolment, such that it can accommodate User ID.  The administrator needs to correctly configure the User Record Reference parameter by using Terminal Menu or Webserver.
Page 386: User Interface
MorphoAccess® SIGMA Series - Administrator Guide Access Control by Authentication User Interface The authentication process starts when the user presents his contactless card in front of the terminal (where the antenna of the contactless smartcard reader is located). Database Figure 332: Authentication without biometric control, and with the user login The User ID is read on the user’s card and searched in the local database.
Page 387: Authentication Process Specified By User's Card
MorphoAccess® SIGMA Series - Administrator Guide Access Control by Authentication Authentication process specified by User's card Description  When the administrator enables this mode, the conditions for allowing access are specified by a dedicated data on the user’s card. This implies that different authentication checks can be performed on the same terminal for different users, based on a ‘specific’...
Page 388: Activation Key
MorphoAccess® SIGMA Series - Administrator Guide Access Control by Authentication  If PIN check is required, the user's PIN must be on user's card.  All other data is ignored.  The required data must be stored according to TLV format. The user’s card format (and the TLV format) is described in the MorphoAccess®...
Page 389 MorphoAccess® SIGMA Series - Administrator Guide Access Control by Authentication Once the authentication process is completed, the terminal automatically loops back and waits for another user’s card presentation, irrespective of the outcome of the authentication process (pass/fail). PIN check disabled, Biometric check mandatory When the administrator enables this mode, the terminal requires the user to place a finger on the biometric sensor.
Page 390: Allowed Format For User's Identifier
MorphoAccess® SIGMA Series - Administrator Guide Access Control by Authentication Allowed format for User's identifier TLV structured data The User ID (user’s identifier) is stored in ASCII characters within a TLV structure. This is the default configuration of the MorphoAccess® SIGMA Family terminal: the related parameters are listed in the table below for each type of card: Parameter Name Parameter Value...
Page 391 MorphoAccess® SIGMA Series - Administrator Guide Access Control by Authentication The administrator can refer to the document: MorphoAccess® terminals Contactless Card Specification. This is a dedicated document that describes the logical structure of the contactless smartcard. 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 392: Binary Data
MorphoAccess® SIGMA Series - Administrator Guide Access Control by Authentication Binary Data Description The MorphoAccess® SIGMA Family terminal is able to use a binary value to read on specific location on user’s card, as user’s identifier. The terminal in legacy modes can also write smart card in binary data format.
Page 393 MorphoAccess® SIGMA Series - Administrator Guide Access Control by Authentication User Identifier to be read in binary format sc_binary_read.data_format = 1 Binary format sc_tlv_mifare.start_block [4 - 215] First block to read on card sc_binary_read.data_length_num_bytes User ID length in bytes and additional bits limited to 8 bytes (i.e.
Page 394 MorphoAccess® SIGMA Series - Administrator Guide Access Control by Authentication Example: 32 bits user’s identifier within a 37-bits Wiegand frame The user’s card contains, at the first block of sector 15 a full 37 bits Wiegand frame (which includes start and stop bits, the site code of the sender, and user’s identifier). The first block in sector 15 is block 46.
Page 395: Section 13 : Multifactor Access Control Mode
MorphoAccess® SIGMA Series - Administrator Guide Multifactor Access Control Mode Section 13 : Multifactor Access Control Mode 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 396: Multi-Factor Mode
MorphoAccess® SIGMA Series - Administrator Guide Multifactor Access Control Mode Multi-factor Mode Description The MorphoAccess® SIGMA Family terminal authorizes simultaneous activation of the access control mode by identification and one of the access control modes by authentication. This is the first user action which automatically selects the access right control process to be executed.
Page 397: Activation Keys
MorphoAccess® SIGMA Series - Administrator Guide Multifactor Access Control Mode Activation keys  The administrator needs to enable the Trigger event through Biometric, Contactless Card, Keypad and External Database. 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 398: Section 14 : Tamper Settings For Terminal Security
MorphoAccess® SIGMA Series - Administrator Guide Tamper Settings for Terminal Security Section 14 : Tamper Settings for Terminal Security 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 399: Tamper Setting For Terminal Security
MorphoAccess® SIGMA Series - Administrator Guide Tamper Settings for Terminal Security Tamper Setting for Terminal Security The MorphoAccess® SIGMA Family terminal can detect two intrusion attempt types:  Someone tries to steal the complete terminal,  Someone tries to open the terminal Besides Webserver, these configurations are possible via MorphoBioToolbox and distant commands also.
Page 400: Section 15 : Wiegand Configurations
MorphoAccess® SIGMA Series - Administrator Guide Section 15 : Wiegand Configurations 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 401: Wiegand Parameters Settings
MorphoAccess® SIGMA Series - Administrator Guide Wiegand Parameters Settings MorphoAccess® SIGMA Family terminals can communicate with distant systems, using Wiegand interface. The protocol used for communicating on Wiegand channel is called Wiegand protocol. It is required to configure Wiegand input and output string format that is understood by terminal and distant system.
Page 402: Wiegand Parameters Configuration Through Webserver
MorphoAccess® SIGMA Series - Administrator Guide Wiegand Parameters Configuration through Webserver Access Path Webserver > Terminal Settings > Wiegand Pre-requisites  MA_PAC license should be uploaded on terminal  Terminal has factory default settings Screens & Steps Figure 336: Wiegand Settings through Webserver 1.
Page 403 MorphoAccess® SIGMA Series - Administrator Guide Auto-Detect can be configured for Prox Port input format/HID Card Number Format and External Port Input Format. Please refer to MA SIGMA - Application note - Wiegand formats for more information. Kindly follow the notes for Auto-Detect. 1.
Page 404 MorphoAccess® SIGMA Series - Administrator Guide The last received input Wiegand frame format can be applied on the output Wiegand format, as defined in “Complete control configuration”. This can be activated by applying the value, “Wiegand Last Format Input” to “Wiegand event Verification fail” or “Wiegand event Verification pass”...
Page 405: Section 16 : Threat Level Configurations
MorphoAccess® SIGMA Series - Administrator Guide Threat Level Configurations Section 16 : Threat Level Configurations 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 406: Threat Level Configuration
MorphoAccess® SIGMA Series - Administrator Guide Threat Level Configurations Threat Level Configuration This feature allows an administrator to set threat levels using the TTL input lines. When enabled, the TTL signals can define the level of security and also can be used to compel users to use a specific authentication method.
Page 407 MorphoAccess® SIGMA Series - Administrator Guide Threat Level Configurations 2. User can change the default settings of GPI to Threat Level Mapping. Select the threat level corresponding to GPI line 1 and GPI line 0 3. Click on Save Figure 338: Configuring Command Based Threat Level 4.
Page 408: Section 17 : Time And Attendance Configuration
MorphoAccess® SIGMA Series - Administrator Guide Section 17 : Time and Attendance Configuration 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 409: Time And Attendance Synoptic
MorphoAccess® SIGMA Series - Administrator Guide Time and Attendance Synoptic MorphoAccess® SIGMA Family terminals can be configured to work in Time and Attendance (T&A) mode. When T&A mode is enabled, each terminal event logged would have some attendance information (such as entry time, exit time, etc.). When the time and attendance feature is activated, the home screen of the terminal displays certain function keys or a bitmap file.
Page 410 MorphoAccess® SIGMA Series - Administrator Guide Parameter Configuration Time and Attendance Mode Activation time_and_attendance.tna_mode If an administrator selects parameter value as 0, the T&A mode is disabled. If an administrator selects parameter value as 1, the T&A mode is enabled. When T&A is enabled, it will show 2 F-keys for MorphoAccess®...
Page 411: T&A Mode In Morphoaccess® Sigma Lite+ Series
MorphoAccess® SIGMA Series - Administrator Guide T&A Mode in MorphoAccess® SIGMA Lite+ Series There are 2 function keys that can be associated with T&A action and displayed to the user. When T&A data is required from the user, the terminal displays the Time and Attendance screen below: Figure 339: Two Function Key Mode for MALite In the above sample screen, the IN function is associated to”...
Page 412 MorphoAccess® SIGMA Series - Administrator Guide Figure 340: Time and Attendance Screen in Normal Mode In the above sample screen, the IN function is associated to F1 key, OUT function is associated to F2 key, IN Duty is to F3 and OUT Duty is to F4. A user can select any of the Function Key to input required T&A action.
Page 413 MorphoAccess® SIGMA Series - Administrator Guide Extended Mode In extended mode, there are 16 function keys that can be configured and displayed to the user. When T&A data is required from the user, the terminal displays the Time and Attendance screen below: Figure 341: Time and Attendance Screen in Extended Mode 1x16 Figure 342: Time and Attendance Screen in Extended Mode 2x8...
Page 414 MorphoAccess® SIGMA Series - Administrator Guide The selected function is written in the access request record, stored in the log file, and included in the "User Identifier" message sent to a distant system. After selection, the MorphoAccess® SIGMA Family terminal switches in biometric mode (identification or authentication).
Page 415: T&A Mode Mandatory Or Optional Scenarios
MorphoAccess® SIGMA Series - Administrator Guide T&A Mode Mandatory or Optional Scenarios  Mandatory: An administrator can set T&A Mode as Mandatory. It means it is mandatory for the user to input T&A action by selecting function key, in order to get access. There are three possible scenarios when T&A is in normal mandatory mode and user initiates an access request.
Page 416: Time And Attendance Configuration Through Webserver
MorphoAccess® SIGMA Series - Administrator Guide Time and Attendance configuration through Webserver Access Path Webserver > Terminal Settings > Time and Attendance Screens & Steps Figure 343: Normal Time and Attendance mode 1. Click on Enable Time and Attendance, for enabling this mode Click on Mandatory Use of Function Keys.
Page 417 MorphoAccess® SIGMA Series - Administrator Guide NOTE: Icon mode display is not applicable for T&A extended mode. Text mode is not available for MorphoAccess® SIGMA Lite+ Series. If an administrator requires T&A in Normal mode, then do not select Extended T&A mode check box.
Page 418: T&A - Mandatory Mode Work Flow Diagram
MorphoAccess® SIGMA Series - Administrator Guide T&A - Mandatory Mode Work Flow Diagram Figure 344: Time and Attendance in Mandatory Mode Workflow Diagram 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 419: T&A - Non Mandatory Mode Work Flow Diagram
MorphoAccess® SIGMA Series - Administrator Guide T&A - Non Mandatory Mode Work Flow Diagram Figure 345: Time and Attendance in Non-Mandatory Mode Workflow Diagram 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 420: Section 18 : Configuring Schedules
MorphoAccess® SIGMA Series - Administrator Guide Section 18 : Configuring Schedules 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 421: Configuring Schedules
MorphoAccess® SIGMA Series - Administrator Guide Configuring Schedules Define Access Schedule Access Schedules is used to define a time slot, during which access is allowed, for example during working hours of working days. Before and after the selected timings, the access is denied to the user, even if authenticated successfully.
Page 422 MorphoAccess® SIGMA Series - Administrator Guide Adding a New Access Schedule through Webserver Access Path Webserver > Schedules > Access Schedules Screens & Steps Figure 346: Adding Access Schedule 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 423 MorphoAccess® SIGMA Series - Administrator Guide 1. The list of default access schedules is displayed. No Access and All Access are by default created and not editable. An administrator can add new schedules as per requirement 2. Click on Add a Schedule to create a new access schedule 3.
Page 424 MorphoAccess® SIGMA Series - Administrator Guide Editing Access Schedule through Webserver Figure 347: Editing Access Schedule 1. Select an access schedule from the list 2. Click on Edit the Selected Schedule tab NOTE: The default access schedules cannot be modified. 3.
Page 425: Define Holiday Schedule
MorphoAccess® SIGMA Series - Administrator Guide 6. The Administrator can delete access schedule by clicking on the Delete the Selected Schedule Define Holiday Schedule Using holiday schedule, an administrator can control access of users on holidays. Holiday Schedule can be defined for the public holidays of entire Year. When user tries to access, terminal will authenticate user and on successful authentication, terminal will check if Holiday Schedule is to be considered.
Page 426 MorphoAccess® SIGMA Series - Administrator Guide Screens & Steps Figure 348: Creating a Holiday Schedule 1. Enter Schedule Name, usually the name of the holiday (such as "Christmas") 2. Select Start Date and End Date of the holiday, by default the date format is YYYY-MM- DD.
Page 427 MorphoAccess® SIGMA Series - Administrator Guide Door Open Schedule Configuration The Door Open Schedule option allows terminal to keep the Door Unlocked for a specific period of time. Using Webserver interface, the Door Open Schedule can be defined. During this period, access is granted without any access rights check.
Page 428 MorphoAccess® SIGMA Series - Administrator Guide Results As per the Door Open Schedule, terminal will send signal to door control panel to open the door at a start time of the schedule. The door is opened (or unlocked) till the end time of the schedule.
Page 429: Section 19 : Controller Feedback
MorphoAccess® SIGMA Series - Administrator Guide Section 19 : Controller Feedback 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 430: Controller Feedback
MorphoAccess® SIGMA Series - Administrator Guide Controller Feedback The administrator can configure parameters that enable the Access Controller to send feedback messages on every event reported by the terminal. Besides Webserver, these configurations are possible via distant commands also. Access Path Webserver >...
Page 431 MorphoAccess® SIGMA Series - Administrator Guide d. Feedback over TTL: Select Feedback over TTL, if controller feedback is to be received on Wiegand String. The following parameters need to be configured, only if Wiegand channel is used. 2. Select Feedback Lines, it means the number of lines in which access controller will send feedback to terminal.
Page 432 MorphoAccess® SIGMA Series - Administrator Guide 6. Consider Timeout as Reject: This function is valid for Access Denied feedback only. If it is enabled, then on timeout the LCD text specified for Access Rejected will be displayed on terminal LCD. If ‘Consider timeout as Reject’ is unchecked, “Timeout” message will be displayed on LCD.
Page 433 MorphoAccess® SIGMA Series - Administrator Guide 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 434: Section 20 : Osdp Protocol Support
MorphoAccess® SIGMA Series - Administrator Guide OSDP Protocol Support Section 20 : OSDP Protocol Support 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 435: Description
MorphoAccess® SIGMA Series - Administrator Guide OSDP Protocol Support Description MorphoAccess® SIGMA Family terminals can be configured to communicate with external Control Panel (CP) using OSDP (Open Supervised Device Protocol). OSDP is a communication protocol that allows Peripheral Devices (PD) such as MorphoAccess® SIGMA Family terminals to interface with Control Panels (CP) or other security management systems.
Page 436: Osdp Commands And Responses
MorphoAccess® SIGMA Series - Administrator Guide OSDP Protocol Support OSDP Commands and Responses The following are the OSDP commands supported by MorphoAccess® SIGMA Family terminals that are sent from the CP to the PD. For more information on OSDP commands and its responses, please refer to Open Supervised Device Protocol (OSDP) Version 2.1.7 on SIA Website https://www.securityindustry.org/Pages/Standards/OSDP.aspx...
Page 437 Syntax: osdp_TEXT (Reader Number, Text Command, Temp of a command) Text time, Row, Column, Text Length, String) Example: osdp_TEXT (0, 2, 0, 1, 1, 64, “HELLO WELCOME TO SAFRAN!!) PD -> CP (Response to a osdp_ACK in case of Success else osdp_NACK for failure command) Example: osdp_ACK CP ->...
Page 438 (Start/Request of a time, Row, Column, Text Length, String) command) Example: osdp_TEXT (0, 2, 0, 1, 1, 64, “HELLO WELCOME TO SAFRAN!!) PD -> CP (Response osdp_ACK in case of Success else osdp_NACK for failure to a command) Example: osdp_ACK CP ->...
Page 439 MorphoAccess® SIGMA Series - Administrator Guide OSDP Protocol Support The MorphoAccess® SIGMA Lite+ terminal has a dedicated, full-screen OSDP display, in addition to its home display (as opposed to the MorphAccess® SIGMA terminal, for which the OSDP display is integrated in the home display). The OSDP screen displays LED and the text as requested by the CP through OSDP commands like osdp_LED and osdp_TEXT.
Page 440 MorphoAccess® SIGMA Series - Administrator Guide OSDP Protocol Support osdp_POLL command This command is used as general inquiry by the panel. The following are the possible responses for osdp_POLL command. 1. osdp_RAW: Terminal responds with this command when it completes the authentication process of smart card/external port/prox card/ identification.
Page 441: Section 21 : User Control Configurations
MorphoAccess® SIGMA Series - Administrator Guide Section 21 : User Control Configurations 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 442: User Control Configurations
MorphoAccess® SIGMA Series - Administrator Guide User Control Configurations User Control configurations consists the list of parameters which terminal should check for authenticating and granting access to the user. An administrator can enable or disable these parameters. Besides Webserver, these configurations are possible via MorphoBioToolbox and distantcommands also.
Page 443 Keyboard or External trigger source). Only the controls intended to validate a user's identity are suppressed. Note: Face capture is still performed if configured for MorphoAccess SIGMA Series terminal. Other checks such as access schedule, holiday schedule, banned card, authorized list, expiry date, trigger check, reference check, etc. are still performed normally.
Page 444 MorphoAccess® SIGMA Series - Administrator Guide 10. Enable external database: If enabled, the polling mode of the terminal will be activated, in that case user’s data will be checked with the data stored in external database. Refer “Polling Mode” for understanding polling mode. 11.
Page 445 MorphoAccess® SIGMA Series - Administrator Guide b. If set to “Trigger Event”, then user rules are retrieved based on user control trigger source i.e. user rule retrieved from smartcard for smartcard triggered user control operation and user rule retrieved from terminal database for other trigger source.
Page 446: Section 22 : Event Configurations
MorphoAccess® SIGMA Series - Administrator Guide Section 22 : Event Configurations 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 447: Event Configurations
MorphoAccess® SIGMA Series - Administrator Guide Event Configurations Events which can be monitored in MorphoAccess® SIGMA Family terminal are listed in ‘Event’ screen of Webserver. An administrator can enable or disable the monitoring and reporting events that can be triggered on terminal. An administrator can also configure which events are to be sent to access controller, GPO TTL lines and its data clock id.
Page 448 MorphoAccess® SIGMA Series - Administrator Guide Figure 354: Events Monitoring Configuration 1. Enable the monitoring of Events by selecting the checkboxes corresponding the event 2. An administrator can also select the events which are required to be Reported to Controller 3.
Page 449: Section 23 : Mmi (Man-Machine Interface) Configurations
MorphoAccess® SIGMA Series - Administrator Guide MMI (Man-Machine Interface) Configurations Section 23 : MMI (Man- Machine Interface) Configurations 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 450: Mmi (Man-Machine Interface) Menu
MorphoAccess® SIGMA Series - Administrator Guide MMI (Man-Machine Interface) Configurations MMI (Man-Machine Interface) Menu This section provides various configurations that an administrator can make to the terminal LCD. Besides Webserver, these configurations are possible via MorphoBioToolbox and distant commands also. MMI Features/Function name SIGMA Series SIGMA Lite+ Series...
Page 451 MorphoAccess® SIGMA Series - Administrator Guide MMI (Man-Machine Interface) Configurations ✔ ✖ Audio for Tamper ✔ ✔ Display User ID on Access Granted ✔ ✔ Display Time Stamp on Access Granted ✔ ✖ Log-in Option ✔ ✖ Idle Video Timeout ✔...
Page 452: Section 24 : Proxy Mode
MorphoAccess® SIGMA Series - Administrator Guide Section 24 : Proxy Mode 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 453: Presentation Of Proxy (Or Slave) Mode
MorphoAccess® SIGMA Series - Administrator Guide Presentation of Proxy (or slave) mode Process The administrator can configure the MorphoAccess® SIGMA Family terminal in the proxy mode. This operating mode allows controlling the MorphoAccess® SIGMA Family terminal remotely via IP link or RS422 (Applicable to MorphoAccess® SIGMA Series only). This is achieved by using a set of biometric and databases management commands.
Page 454: Local Signals
MorphoAccess® SIGMA Series - Administrator Guide Local signals When the terminal is waiting for a command from the distant system, there is no local signal (biometric sensor backlight off, status light off). But when a command is in progress the terminal emits the signals related to the function. This implies that: ...
Page 455: Proxy Mode Use Sample
MorphoAccess® SIGMA Series - Administrator Guide Proxy mode use sample When terminal is in proxy mode, then the administrator can control several functions of the terminal, by using distant commands. For example, if it is required to take the backup of terminal database, the administrator can activate proxy mode of the terminal and take a backup.
Page 456: Section 25 : Polling Mode
MorphoAccess® SIGMA Series - Administrator Guide Polling Mode Section 25 : Polling Mode 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 457: Presentation Of Polling Mode
MorphoAccess® SIGMA Series - Administrator Guide Polling Mode Presentation of Polling mode If the administrator enables the polling mode, the MorphoAccess® SIGMA Family terminal does not verify user template in its local database. This mode is useful when the user templates are stored in external database.
Page 458: Polling Mode Activation
MorphoAccess® SIGMA Series - Administrator Guide Polling Mode Polling mode activation The administrator can activate the Polling mode through Webserver > Complete Configuration. This is done by setting the parameter “ucc.enable_external_database” to ‘1’. Please refer to MorphoAccess SIGMA &and SIGMA Lite Series Parameters User Guide to know as to how to set this parameter.
Page 459: Section 26 : Messages Sending
MorphoAccess® SIGMA Series - Administrator Guide Messages Sending Section 26 : Messages Sending 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 460: Principle
MorphoAccess® SIGMA Series - Administrator Guide Messages Sending Principle The administrator can configure the MorphoAccess® SIGMA Family terminal, to generate and send messages to another physical entity, upon the occurrence of specific events during the access control process. The events that lead to generation and sending of messages sending are, as follows. ...
Page 461: Events
MorphoAccess® SIGMA Series - Administrator Guide Messages Sending Events The MorphoAccess® SIGMA Family terminal allows the administrator to select one or more events on which messages can be sent to the external controller. An administrator can enable or disable events using Webserver or distant command. Please refer to “Event Configuration”...
Page 462: Sending Interfaces
MorphoAccess® SIGMA Series - Administrator Guide Messages Sending Sending Interfaces The administrator can choose the interfaces that will be available for the messages sending process. By default, no interface is available. The administrator needs to set the parameters mentioned below for activating remote sending message: Number of available interfaces ...
Page 463: Section 27 : Compatibility With An Access Control System
MorphoAccess® SIGMA Series - Administrator Guide Compatibility with an Access Control System Section 27 : Compatibility with an Access Control System 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 464: Internal Relay Activation On Access Granted Result
MorphoAccess® SIGMA Series - Administrator Guide Compatibility with an Access Control System Internal Relay activation on Access Granted result Description If the result of the access rights check is successful, the internal relay may be optionally activated, for example, to directly trigger a door switch. The duration of the activation of the internal relay can be modified by a specific configuration key.
Page 465: Activation Key
MorphoAccess® SIGMA Series - Administrator Guide Compatibility with an Access Control System Activation key The administrator can configure the following parameters. These parameters are related to internal relay activation, in the event of an access being granted. Parameters SIGMA Series SIGMA Lite Series SIGMA Extreme Series ✔...
Page 466: Configuration Key
MorphoAccess® SIGMA Series - Administrator Guide Compatibility with an Access Control System Select “2” to enable SDAC mode Configuration key Parameter name Value Description gpio.sdac_door_unlock_dur 2 - 60 sec. The administrator can configure this parameter to set the duration for which SDAC door should (10-Default) be opened after access is granted.
Page 467: External Activation Of The Internal Relay
MorphoAccess® SIGMA Series - Administrator Guide Compatibility with an Access Control System External activation of the internal relay Description The administrator can enable this function to allow the activation of the terminal internal relay via a push button connected between the LED1 and the GND wires. When this function has been enabled, the internal relay is activated in two cases: when the terminal authorizes the access after access rights check, and when a contact is closed between the LED1 and GND terminals.
Page 468: Activation Key
MorphoAccess® SIGMA Series - Administrator Guide Compatibility with an Access Control System Activation key A specific configuration key enables this feature. Parameter name Value Description The administrator can set an exit mode in SDAC, gpio.sdac_rte_mode 0, 1 by using this parameter. Following values can be configured: ...
Page 469: Access Request Result Log File
MorphoAccess® SIGMA Series - Administrator Guide Compatibility with an Access Control System Access Request Result Log File Description The administrator can enable this functionality so that, the terminal creates a record for each access request in a local log file. Each record includes: ...
Page 470: Activation Key
MorphoAccess® SIGMA Series - Administrator Guide Compatibility with an Access Control System The format of the “Log File Full Warning” message is described in the MorphoAccess® 5G Series – Remote Message Specification document. Activation key The administrator can enable or disable the creation of a record for each access request, by using only one configuration key.
Page 471: Sending An Access Control Result Message
MorphoAccess® SIGMA Series - Administrator Guide Compatibility with an Access Control System Sending an Access Control Result Message Presentation The administrator can configure the MorphoAccess® SIGMA Family terminal to send a message which contains the result of the access control, to a distant terminal. It can send the access control result using different channels and different protocols.
Page 472: Serial Port (Output Only)
MorphoAccess® SIGMA Series - Administrator Guide Compatibility with an Access Control System Serial Port (Output only) Feature/Function name SIGMA Series SIGMA Lite Series ✔ ✔ Wiegand or Clock & Data protocols (For Serial Communication) ✔ ✔ RS485 (Serial Protocol) ✔ ✖...
Page 473 MorphoAccess® SIGMA Series - Administrator Guide Compatibility with an Access Control System Clock & Data protocol The description provided for Wiegand protocol (see previous section) applies to Clock & Data protocol as well. The sending of the message is conditioned to only one configuration key. Parameter name Value Description...
Page 474: Ethernet Port
MorphoAccess® SIGMA Series - Administrator Guide Compatibility with an Access Control System Ethernet port Protocol selection The administrator can configure the terminal to send the access control result messages via an Ethernet link. The protocol could be one of UDP/TCP and TLS/SSL. MorphoAccess®...
Page 475: Note About Terminal Clock Deviation
MorphoAccess® SIGMA Series - Administrator Guide Compatibility with an Access Control System Note about Terminal Clock Deviation The message sent through IP and RS422 or RS485 protocols includes the date/time of access control result. Please refer to “Date / Time synchronization”...
Page 476: Section 28 : Terminal User Interface
MorphoAccess® SIGMA Series - Administrator Guide Terminal User Interface Section 28 : Terminal User Interface 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 477: Audio Man Machine Interface
MorphoAccess® SIGMA Series - Administrator Guide Terminal User Interface Audio Man Machine Interface Audible signal The administrator can tune the volume of the audible signal by tweaking the following configuration key. The terminal can be configured to emit an audio signal, in the event of access being granted or denied or the terminal being tampered, for an instance.
Page 478: Terminal States
MorphoAccess® SIGMA Series - Administrator Guide Terminal User Interface Terminal States Identification, Authentication or Multi-factor mode: waiting for a finger or a card  In identification mode, the terminal is waiting for a finger to be placed on the biometric sensor.
Page 479 MorphoAccess® SIGMA Series - Administrator Guide Terminal User Interface Biometric Sensor start up error The terminal fails to start the biometric sensor. If the trouble persists after restarting the terminal, please contact our customer service. Maintenance: terminal configuration in process This signal indicates that a configuration operation is in process, whether by TCP or by USB mass storage key.
Page 480 MorphoAccess® SIGMA Series - Administrator Guide Terminal User Interface Change Key Not OK This signal is emitted when the Card is encoded and it is detected as an Admin Card. However, the corresponding keys on the card are incorrectly written. Maintenance: USB mass storage key can be removed This signal is emitted when the USB Mass Storage key, used to configure the terminal, can be safely removed from the USB port.
Page 481: Enrolment
MorphoAccess® SIGMA Series - Administrator Guide Terminal User Interface Finger removed too early The terminal emits this signal when the finger is removed before the end of biometric data acquisition. Enrolment Waiting for a finger The enrolment sequence is launched and the terminal is waiting for a user to place a finger on the biometric sensor.
Page 482 MorphoAccess® SIGMA Series - Administrator Guide Terminal User Interface The enrolment sequence has completed successfully. Depending on how long the biometric data registration process has taken, the terminal may emit the signal Enrolment complete – Registration of biometric data in process. Enrolment Error The enrolment sequence has not completed successfully.
Page 483: Led - Buzzer Sequence
MorphoAccess® SIGMA Series - Administrator Guide Terminal User Interface LED – Buzzer Sequence For MA SIGMA / SIGMA Extreme Series Biometric Status LED Terminal States Sensor Buzzer (On top of the terminal) backlight Identification, Authentication or Multi-factor mode: waiting for a finger or a card Authentication mode, after presentation of a card, waiting for a finger or biometric data...
Page 484 MorphoAccess® SIGMA Series - Administrator Guide Terminal User Interface Biometric Status LED Terminal States Sensor Buzzer (On top of the terminal) backlight Identification second Insignificant Authentication - Access denied pitched notes Timeout while waiting for second Insignificant finger on the sensor pitched notes Finger removed too early Waiting for a finger...
Page 485 MorphoAccess® SIGMA Series - Administrator Guide Terminal User Interface Action Buzzer Green Blue Yellow Purple Cyan USB Key Detected √ USB Script In Progress √ (Blink) USB Script Successful √ √ USB Script Error √ √ Change Key OK √ √...
Page 486: Section 29 : Compatibility Accessories, Software Licenses And Software
MorphoAccess® SIGMA Series - Administrator Guide Compatibility Accessories, Software Licenses and Software Applications Section 29 : Compatibility Accessories, Software Licenses and Software Applications 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 487: Compatible Accessories & Software Licenses
MorphoAccess® SIGMA Series - Administrator Guide Compatibility Accessories, Software Licenses and Software Applications Compatible Accessories & Software Licenses The following items can be ordered directly from Morpho or from an official distributor, in order to leverage all the benefits of being a MorphoAccess® SIGMA Family terminal administrator. ...
Page 488: Compatible Software Applications
MorphoAccess® SIGMA Series - Administrator Guide Compatibility Accessories, Software Licenses and Software Applications Compatible software applications MorphoAccess® SIGMA Family terminals are fully compatible with:  The low level protocol using thrift commands, for more information, please refer to “Host System Interface Guide” ...
Page 489: Section 30 : Recommendations
MorphoAccess® SIGMA Series - Administrator Guide Recommendations Section 30 : Recommendations 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 490: Warning
MorphoAccess® SIGMA Series - Administrator Guide Recommendations Warning The manufacturer cannot be held responsible in case of non-compliance with the following recommendations or incorrect use of the terminal. General precautions  Do not attempt to repair the MorphoAccess® SIGMA Family terminal by yourself. The manufacturer cannot be held responsible for any damage/accident that may result from attempts to repair components.
Page 491: Sd Card
MorphoAccess® SIGMA Series - Administrator Guide Recommendations SD card Feature/Function name SIGMA Series SIGMA Lite Series SIGMA Extreme Series ✔ ✖ SD card support  Even if the SD card is provided with the terminal, the administrator is advised to use branded ones such as Verbatim.
Page 492: Recommended Conditions For Face Detection
MorphoAccess® SIGMA Series - Administrator Guide Recommendations Recommended Conditions for Face Detection User Face Position  The user should face toward the terminal while identification/authentication  The user should stand at the distance where terminal can recognize face (not too far or too close) ...
Page 493: Annex 1 : Finger Placement Recommendation
MorphoAccess® SIGMA Series - Administrator Guide Recommendations Annex 1 : Finger Placement Recommendation 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 494 MorphoAccess® SIGMA Series - Administrator Guide Recommendations Most Useful Areas for Biometric Data The terminal is designed to capture the area containing the most useful biometric data. In fingerprints, this is usually at the center of the first phalanx. This is illustrated in the figure below: Area containing the maximum information...
Page 495 MorphoAccess® SIGMA Series - Administrator Guide Recommendations Position of Finger Finger Height Figure 360: Finger Height Incorrect Position:  Do not place the finger tip on the top of the fingertip guide  Do not place the finger tip on the surface of the sensor Correct Position: ...
Page 496 MorphoAccess® SIGMA Series - Administrator Guide Recommendations Finger Angle IDEAL POSITION Figure 361: Finger Angle Incorrect Position:  Do not tilt the finger on right or left side of the sensor Correct Position:  The finger must be parallel to the sides of the sensor 2017_2000025464-v03 This document and the information therein are the property of Morpho.
Page 497 MorphoAccess® SIGMA Series - Administrator Guide Recommendations Finger Inclination IDEAL POSITION Figure 362: Finger Inclination Incorrect Position:  Do not leave the finger in the air  Do not bend finger upward or downward Correct Position:  Finger must be parallel to the sensor surface 2017_2000025464-v03 This document and the information therein are the property of Morpho.
Page 498 MorphoAccess® SIGMA Series - Administrator Guide Recommendations Finger rotation IDEAL POSITION Figure 363: Finger Rotation Incorrect Position:  Do not roll finger Correct Position:  Finger must be parallel to the sensor surface 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 499 MorphoAccess® SIGMA Series - Administrator Guide Recommendations Finger Condition When finger biometric data acquisition is difficult, please follow the recommendations listed below:  The finger is cold  Solution: warm up the finger  The finger is wet  Solution: wipe the finger ...
Page 500: Annex 2 : Comparison Of Authentication Mode With Contactless Card
MorphoAccess® SIGMA Series - Administrator Guide Recommendations Annex 2 : Comparison of Authentication mode with Contactless Card 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 501 MorphoAccess® SIGMA Series - Administrator Guide Recommendations Contactless Modes Table Operation Actions Performed by Terminal Authentication with biometric  Read ID on contactless card. templates in database  Retrieve corresponding templates from the database.  Biometric authentication using these templates. ...
Page 502 MorphoAccess® SIGMA Series - Administrator Guide Recommendations Required Tags on Contactless Card Operation CARD Templat Templa BIOPI MODE te 2 Authentication with templates database Authentication with templates on card Card mode authentication (ID_ONLY) Card mode authentication (PKS) Authentication with templates database –...
Page 503: Annex 3 : Bibliography
MorphoAccess® SIGMA Series - Administrator Guide Recommendations Annex 3 : Bibliography 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 504 MorphoAccess® SIGMA Series - Administrator Guide Recommendations How to get latest version of the documents The last version of the documents is available on a CD/ROM package from our factory, or can be downloaded from our web site at the address below: www.biometric-terminals.com (Login and password required).
Page 505 MorphoAccess® SIGMA Series - Administrator Guide Recommendations Documents concerning the MorphoAccess® SIGMA Family terminals Document about installing the terminal MorphoAccess® 5G Series – Recommendations for Secure Installation, ref. 2015_2000012312 - MorphoAccess® 5G Series – Recommendations for Secure Installation This document describes how to secure your installation. This document is in English. ref.
Page 506 MorphoAccess® SIGMA Series - Administrator Guide Recommendations Documents for Developer MorphoAccess® SIGMA Family – Parameters Guide, ref. 2017_2000024583 - MorphoAccess® SIGMA Family Parameters Guide This document contains the full description of all the configuration parameters for MorphoAccess® SIGMA Family terminals. This document is in English. MorphoAccess®...
Page 507 MorphoAccess® SIGMA Series - Administrator Guide Recommendations Documents concerning the MorphoAccess® SIGMA Series terminal Document about installing the terminal MorphoAccess® SIGMA Series Installation Guide, ref. 2014_0000000606 - MA SIGMA - Installation Guide This document describes terminal physical mounting procedure, electrical interfaces and connection procedures.
Page 508 MorphoAccess® SIGMA Series - Administrator Guide Recommendations MorphoAccess® 5G Series – UpgradeProcessEnhancement, ref. 2016_2000021771 - MorphoAccess® 5G Series - ApplicationNotes - UpgradeProcessEnhancement This document describes how to use the new upgrade mechanism with MorphoAccess® SIGMA Series terminal. This document is in English. MorphoAccess®...
Page 509 MorphoAccess® SIGMA Series - Administrator Guide Recommendations Documents concerning the MorphoAccess® SIGMA Lite Series terminal Document about installing the terminal MorphoAccess® SIGMA Lite Series Installation Guide, ref. 2015_2000007248 - MA SIGMA Lite - Installation Guide This document describes terminal physical mounting procedure, electrical interfaces and connection procedures.
Page 510 MorphoAccess® SIGMA Series - Administrator Guide Recommendations Documents concerning the MorphoAccess® SIGMA Extreme Series terminal Document about installing the terminal MorphoAccess® SIGMA Extreme Series Installation Guide, ref. 2017_2000024418 - MorphoAccess® SIGMA Extreme Series - Installation Guide This document describes terminal physical mounting procedure, electrical interfaces and connection procedures.
Page 511: Annex 4 : Glossary, Acronyms And Abbreviation
MorphoAccess® SIGMA Series - Administrator Guide Recommendations Annex 4 : Glossary, Acronyms and Abbreviation 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 512 MorphoAccess® SIGMA Series - Administrator Guide Recommendations GLOSSARY  Access Controller/Controller: This term is used for centralized access controller. Terminal communicates with controller for decisions regarding access, to the user.  Terminal: This term is used for MorphoAccess® SIGMA Family terminal, unless explicitly specified.
Page 513 MorphoAccess® SIGMA Series - Administrator Guide Recommendations  Template: A term used to describe the data that is stored during the enrolment process. The data is a mathematical representation of the ridge pattern of the enrolled finger scan.  Primary Template: This is the template that resides in the first template slot on the smart card.
Page 514 MorphoAccess® SIGMA Series - Administrator Guide Recommendations Acronyms and Abbreviations  AUX: Auxiliary  LCD: Liquid Crystal Display  LED: Light Emitting Diode  MAC (address): Media Access Control, a unique identifier assigned to network interfaces for communications on the physical network segment ...
Page 515: Annex 5 : Support
MorphoAccess® SIGMA Series - Administrator Guide Recommendations Annex 5 : Support 2017_2000025464-v03 This document and the information therein are the property of Morpho. They must not be copied or communicated to a third party without the prior authorization of Morpho July 17...
Page 516 MorphoAccess® SIGMA Series - Administrator Guide Recommendations Troubleshooting Customer service Morpho SAV Terminaux Biométriques Boulevard Lénine - BP428 76805 Saint Etienne du Rouvray FRANCE Phone: +33 2 35 64 53 52 Hotline Morpho Support Terminaux Biométriques 18, Chaussée Jules César 95520 Osny FRANCE [email protected]...
Page 517 July 17 Registered Office: Morpho 11, boulevard Gallieni 92130 Issy-les-Moulineaux – France www.safran-identity-security.com...

This manual is also suitable for:

Morphoaccess sigma wr Morphoaccess sigmaMorphoaccess sigma multiMorphoaccess sigma multi wrMorphoaccess sigma prox Morphoaccess sigma prox wr ... Show all

Safran MorphoAccess SIGMA Series Administration Manual

Warning

Revision History

Section 1 : Introduction

Morphoaccess® SIGMA Family Series Terminal

Scope of the Document

About Biometrics

Section 2 : Connecting the Terminal to a Pc

General

Point to Point Ethernet Connection

Connection through Only One Ethernet Switch

Connection through a LAN

Wi-Fi™ Network Configuration

Section 3 : Terminal Configuration and Administration

Understanding Morphoaccess® Configuration

Configuring a Networked Morphoaccess

Morphoaccess® Terminal Database Management

Morphoaccess® Terminal License Management

Terminal Firmware Upgrade

Morphoaccess® SIGMA Family Modes

Section 4 : Morphoaccess® Terminal First Boot Assistant

Assistant Initialization

Date & Time Configuration

Trigger Event

Language Configuration

Show/Hide Language Icon

Ethernet Interface Settings

Wi-Fi™ Configuration

Protocol Configuration

Password Configuration

First Boot Assistance at Next Boot Configuration

Recover Corrupted Components

Section 5 : Morphoaccess® Terminal Administration Menu

Access to Administration Menu

User Menu

Multimedia Menu

System Menu

Communication Menu

Security Menu

USB Menu

Information Menu

Reboot Terminal

Section 6 : Morphoaccess® Terminal : Videophone Facility

Introduction to Videophone

Configure Video Phone Server

Viewing Video Phone Server Details

Delete Video Phone Server

How User Can Make Video Call

Section 7 : Terminal Menu for Morphoaccess® Sigma Lite+ Series

Morphoaccess® SIGMA Lite+ Series Terminal Screens

Steps to Setup Wallpaper

Recover Corrupted Components

Display Screens and Actions

Section 8 : Terminal Configuration through Webserver

Access to Administration Menu through Webserver

Section 9 : Usb Scripts

USB Scripts

Access Control

Access Control Presentation

Preliminary: Adding a Biometric Template in Local Database

Morphoaccess® SIGMA Family Terminal Operating Modes

Access Control Result

Section 11 : Access Control by Identification

Identification Mode Description

Section 12 : Access Control by Authentication

Authentication Process

Biometric Check, Biometric Data on User's Card

PIN Verification - PIN Stored on Card

BIOPIN Verification - BIOPIN Stored on Card

Biometric Check and Biometric Data in Local Database

Authentication with Local Database: User ID Entered from Keyboard

Authentication with Local Database: ID Input from Wiegand or Clock & Data

No Biometric Check, no User ID Check

No Biometric Check, User Identifier in the Database

Authentication Process Specified by User's Card

Allowed Format for User's Identifier

Section 13 : Multifactor Access Control Mode

Multi-Factor Mode

Section 14 : Tamper Settings for Terminal Security

Tamper Setting for Terminal Security