Table of Contents
Always hold the tool and screwdriver bit in a straight line
x
with the screw.
When screwing in wood, it is recommended to drill a pilot
x
hole with a depth equal to the length of the screw. A pilot
hole guides the screw and prevents splintering or
distortion of the wood. For the optimum size of the pilot
hole, refer to the table below.
When screwing in hardwood, also drill a clearance hole
x
with a depth equal to half the length of the screw. For the
optimum size of the clearance hole, refer to the table
below.
Screw size
Pilot hole ø
(softwood)
No. 6 (3.5 mm)
2 mm
No. 8 (4 mm)
3.2 mm
No. 10 (6 mm)
3.5 mm
Accessories
The performance of your tool depends on the accessory used.
Black & Decker and Piranha accessories are engineered to
high quality standards and designed to enhance the performance
of your tool. By using these accessories you will get the very
best from your tool.
This tool uses screwdriver bits and drill bits with a 1/4" (6.35 mm)
hexagonal shank. Piranha Super-lok accessories are designed
for use with this tool.
Maintenance
Your tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
Regularly clean the ventilation slots in your tool using a
x
soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth.
x
Do not use any abrasive or solvent-based cleaner.
Protecting the environment
Tools
Black & Decker provides a facility for recycling
Black & Decker products once they have reached the
end of their working life. This service is provided
free of charge. To take advantage of this service
please return your product to any authorised repair
agent who will collect them on our behalf.
Pilot hole ø
Clearance
(hardwood)
hole
2.5 mm
4 mm
3.5 mm
5.0 mm
4.0 mm
5.7 mm
You can check the location of your nearest authorised repair
agent by contacting your local Black & Decker office at the
address indicated in this manual. Alternatively, a list of
authorised Black & Decker repair agents and full details of our
after-sales service and contacts are available on the Internet
at: www.2helpU.com.
Battery (fig. E)
If you want to dispose of the tool yourself, the
battery must be removed as described below and
Cd
disposed of in accordance with local regulations.
Do not short-circuit the battery terminals. Do not use
tools to remove the battery; only use your fingers.
If possible, operate the tool to run the battery down
x
completely.
Use a screwdriver to remove the clip (8).
x
Pull the front part off the tool.
x
Loosen and remove the screws on the handle clamshells.
x
Lift the batteries out of the tool.
x
Disconnect the wires from the battery terminals.
x
Place the battery in a suitable packaging to ensure that
x
the terminals cannot be short-circuited. Take the battery
to your service agent or a local recycling station. Collected
batteries will be recycled or disposed of properly.
Technical data
Voltage
No-load speed
Max. torque
Bit holder
Weight
Charger
Input voltage
Approx. charging time
EC declaration of conformity
Black & Decker declares that these products conform to:
98/37/EC, 89/336/EEC, 73/23/EEC, EN 50260, EN 55014,
EN 60335, EN 61000
L
(sound pressure): 70 dB(A), L
pA
hand/arm weighted vibration < 2.5 m/s
KC9024
KC36
V
2.4
3.6
DC
-1
min
150
180
Nm 2.4
3.4
6.35 mm hex
6.35 mm hex
kg 0.30
0.34
V
230
AC
h 12
(acoustic power) 85 dB(A),
WA
2
Colin Wills, Director of Engineering
BDCI, 4/F, 2 Dai Wang Street
Tai Po Industrial Estate
Tai Po NT, Hong Kong
5
Hide quick links:
Table of Contents
