Table of Contents
Available languages
Available languages
FUNCTIONAL
DESCRIPTION- JS500,
JS510G, JS590TP, JS4000
1. Variable speed switch
2. Lock-on button
3. Saw blade locking lever
4. Saw blade support roller
5. Saw blade
6. Shoe plate
7. Shoe plate locking knob
8. Saw blade storage compartment
9. Dust blower
10. Dust extraction adaptor
(available on select models -
check packaging for inclusion)
11. Rip fence (available on select
models - check packaging for
inclusion)
FUNCTIONAL
DESCRIPTION - JS600,
JS610G
1. On/off switch
2. Lock-on button
3. Variable speed control knob
4. Orbital action"Turbo" selector
5. Saw blade locking lever
6. Saw blade support roller
7. Saw blade
8. Shoe plate
9. Shoe plate locking knob
10. Saw blade storage compartment
11. Dust blower
12. Dust extraction adaptor
(available on select models -
check packaging for inclusion)
13. Rip fence (available on select
models - check packaging for
inclusion)
Illustrations A, B for Model JS500, JS510G, JS590TP, JS4000
5
10
3
Ills. C, D, E, F for Model JS500, JS510G, JS590TP, JS4000 - Cont.
14
14
9
C
12
12
13
14
E
7
6
7
1
2
B
7
5
D
11 9
F
Illustrations G, H, I,J, K for Model JS600, JS610G
G
7
12
5
I
13 11
K
M
4
7
USE OF EXTENSION CORDS
Make sure the extension cord is in good condition before using. Always use the proper size
extension cords with the tool – that is, proper wire size for various lengths of cord and heavy
enough to carry the current the tool will draw. Use of an undersized cord will cause a drop in
line voltage resulting in loss of power and overheating. For proper size cords see chart
below.
15
MOTOR
Be sure your power supply agrees with nameplate marking. 120 Volts AC only means your
tool will operate on standard 60 Hz household power. Do not operate AC tools on DC. A
16
rating of 120 volts AC/DC means that you tool will operate on standard 60 Hz AC or DC
power. This information is printed on the nameplate. Lower voltage will cause loss of power
and can result in over-heating. All Black & Decker tools are factory-tested; if this tool does
not operate, check the power supply.
ASSEMBLY - JS500, JS510G, JS590TP, JS4000
WARNING: Before attempting any of the following operations, make sure that the tool is
switched off and unplugged and that the saw blade has stopped. Used saw blades can be
hot.
Fitting the saw blade (fig. A)
- Hold the saw blade (5) as shown, with teeth facing forward.
- Push the lever (3) downwards.
- Insert the shank of the saw blade into the blade holder (10) as far as it will go.
- Release the lever.
- Adjust the blade support roller as described below.
Adjusting the blade support roller (fig. B)
After fitting the blade, you need to adjust the blade support roller (4).
- Turn the locking knob (7) in direction A.
H
J
17
L
18
Minimum Gage for Cord Sets
Volts
Total Length of Cord in Feet
120V
0-25
26-50
51-100
(0-7,6m) (7,6-15,2m) (15,2-30,4m) (30,4-45,7m)
240V
0-50
51-100
101-200
(0-15,2m) (15,2-30,4m) (30,4-60,9m) (60,9-91,4m)
Ampere Rating
More
Not more
American Wire Gage
Than
Than
0
-
6
18
16
16
6
-
10
18
16
14
10
-
12
16
16
14
12
-
16
14
12
Not Recommended
SAVE THESE INSTRUCTIONS
16
16
11
14
14
15
16
9
8
9
101-150
201-300
14
12
12
Hide quick links:
Table of Contents
