Page 3
DX410/DX440 or ETERNUS DX8100/DX8400/DX8700 Disk storage system, server, OS, iSCSI HBAs, LAN cards, and drivers. Refer to "FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- Notations" for the notations used in this manual such as product trademarks and product names.
Setting CHAP Authentication ......................... 13 OS Specific Settings ......................14 2.2.1 Setting the CA Reset Groups .......................... 14 2.2.2 Setting the Sub System Parameters (for HP-UX only) ..................15 FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- Copyright 2014 FUJITSU LIMITED P3AM-3972-08ENZ0...
Page 5
Data Transfer Timer setting for VMware ESX....................11 Table 2.12 Inquiry Standard Data Version setting for VMware ESX................11 Table 2.13 Sense Data Conversion setting for Oracle VM Server..................12 FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- Copyright 2014 FUJITSU LIMITED P3AM-3972-08ENZ0...
Page 6
Chapter 1 Workflow This manual is used when performing the setup procedures described in the "Setting up the ETERNUS DX" section of the "FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (iSCSI)" for each OS. Workflow Setting the CA Parameters Set the to-server connection type.
Page 7
Refer "2.2.1 Setting the CA Reset Groups" (page 14) After completing all the required procedures in this manual, follow the procedures in "FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (iSCSI)" for each OS. FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection-...
OFF (Default value): When not using Affinity Mode Affinity Mode ON: When using Affinity Mode Host Affinity Host Response Not available ( When "Host Affinity" is set to "ON") FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- Copyright 2014 FUJITSU LIMITED P3AM-3972-08ENZ0...
For HP-UX, set the [Host Specific Mode] to [HP-UX Mode (SCC)]. Table 2.4 Host Specific Mode setting for HP-UX [Host Specific Mode] setting HP-UX HP-UX Mode (SCC) FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- Copyright 2014 FUJITSU LIMITED P3AM-3972-08ENZ0...
Table 2.7 Sense Data Conversion Pattern setting for Linux ETERNUS Multipath Driver Not used Red Hat Enterprise Linux Linux Recommended SUSE Linux Enterprise Server (When not using GRMPD) FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- Copyright 2014 FUJITSU LIMITED P3AM-3972-08ENZ0...
LUN0 and continuing in ascending order. The server cannot recognize the ETERNUS DX LUNs unless they are assigned in this order. This restriction does not apply when the server is running a Solaris OS. FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- Copyright 2014 FUJITSU LIMITED P3AM-3972-08ENZ0...
If an iSNS server with the server iSCSI name registered does not exist in the network, [Add New iSCSI Host] cannot be used. When the iSNS server does not exist, enter the server iSCSI information manually. FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- Copyright 2014 FUJITSU LIMITED P3AM-3972-08ENZ0...
When multiple ESX servers share ETERNUS DX LUNs, any ETERNUS DX iSCSI port that connects a shared LUN to an ESX server must be assigned to the same reset group, whether multi-paths are used for the ESX servers or not. FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- Copyright 2014 FUJITSU LIMITED...
For HP-UX server, improper logs may be recorded unless sense response is restricted. Therefore, [Disable Load Balance] should be disabled. (Sense response should be restricted.) Note that changing the [Disable Load Balance] setting does not affect on non-HP-UX servers. FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- Copyright 2014 FUJITSU LIMITED P3AM-3972-08ENZ0...
Page 16
However, Fujitsu shall assume no responsibility for any operational problems as the result of errors, omissions, or the use of information in this manual. • Fujitsu assumes no liability for damages to third party copyrights or other rights arising from the use of any information in this manual.