Fujitsu ETERNUS DX200 S3 Configuration Manual
  1. Manuals
  2. Brands
  3. Fujitsu Manuals
  4. Storage
  5. ETERNUS DX200 S3
  6. Configuration manual

Fujitsu ETERNUS DX200 S3 Configuration Manual

Disk storage system
Hide thumbs Also See for ETERNUS DX200 S3:
Table of Contents

Quick Links

See also: Basic Operation Manual, Operating Manual
P3AM-7652-02ENZ0
FUJITSU Storage
ETERNUS DX100 S3/DX200 S3
Disk storage system
Configuration Guide (Basic)
Table of Contents
loading

Related Manuals for Fujitsu ETERNUS DX200 S3

Summary of Contents for Fujitsu ETERNUS DX200 S3

  • Page 1 P3AM-7652-02ENZ0 FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic)
  • Page 2 This page is intentionally left blank.

  • Page 3: About This Manual

    This manual describes all the procedures that are required to start operation of the FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system. This manual is intended for use of FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system in re- gions other than Japan.

  • Page 4: Naming Conventions

    This chapter describes the settings required to operate Advanced Copy. • "Chapter 10 System Status Check" (page 168) This chapter describes the status check for the FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system after system configuration. "Chapter 11 Solution Configuration" (page 174) •...
  • Page 5 "ETERNUS DX100 S3" refers to the FUJITSU Storage ETERNUS DX100 S3 Disk storage system and "ETERNUS • DX200 S3" refers to the FUJITSU Storage ETERNUS DX200 S3 Disk storage system. "ETERNUS DX Disk storage system" refers to the ETERNUS DX100 S3 and ETERNUS DX200 S3 Disk storage • systems.
  • Page 6 The black "Must Do..." circle indicates actions that must be taken. The required ac- tion is both illustrated inside the black disk and written above it (e.g. Unplug). FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
  • Page 7 - Do not use alcohol or other solvents to clean the ETERNUS DX Disk storage system. Warning layout ribbon FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 8 Manufacturer’s label The model name and the serial number are listed. Device ID label The model name and the serial number are listed. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 9 Preface Drive Enclosures • 2.5" type drive enclosure 3.5" type drive enclosure • FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 10 Preface High-density drive enclosure • FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 11 • Power distribution unit for DX100 S3/DX200 S3 (AC200-240V, 2U) Manufacturer’s label Information such as the model name and serial number is indicated. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 12: Table Of Contents

    3.4 LAN Connection Preparation for Operation Management.............. 51 3.4.1 Completing and Attaching the Network Settings Label..................51 3.4.2 LAN Related Specifications...........................52 Chapter 4 Connecting Cables FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 13 6.3 Remote Support Setup......................... 112 6.3.1 Remote Support (by AIS Connect) Setup ......................113 6.3.2 Remote Support (by REMCS) Setup ........................114 FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 14 10.2 RAID Group Check........................169 10.3 Volume Check..........................170 10.4 Checking Copy Sessions ......................171 10.5 Checking LUNs........................... 171 FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 15 11.4.1 Oracle VM Linkage ............................180 11.4.2 VMware Linkage ..............................181 11.4.3 Microsoft Linkage ............................183 11.5 Security ............................. 184 FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 16 Solution — Cloud Platform (Oracle VM Linkage)..................180 Figure 11.5 Solution — Cloud Platform (VMware Linkage) ..................181 Figure 11.6 Solution — Cloud Platform (Microsoft Linkage) ..................183 FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 17 Table 7.1 ETERNUS DX Disk Storage System Operation According to the Settings of the Auto Power Function and the Power Resume Function........................121 FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 18: Chapter 1 Component Names

    This section provides the names of the components in the front of a controller enclosure. ■ 2.5" Type Figure 1.1 Front View of a 2.5" Type Controller Enclosure Operation panel 2.5" drive Flange cover FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 19: Rear

    Host interface (CA#0) Drive interface (OUT) port LAN (RMT) port Host interface (CA#1) LAN (MNT) port Power supply unit (PSU#0) 10. Power supply unit (PSU#1) FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 20: Figure 1.4 Rear Views Of A Controller Enclosure (When Two Controllers Are Installed)

    10. Power supply unit (PSU#1) Controller (CM#0) Controller (CM#1) PWC port Host interface (CA#0) Drive interface (OUT) port LAN (RMT) port Host interface (CA#1) LAN (MNT) port FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 21: Drive Enclosures

    2.5" drive Flange cover ■ 3.5" Type Figure 1.6 Front View of a 3.5" Type Drive Enclosure Operation panel 3.5" drive Flange cover FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 22: Rear

    Figure 1.8 Rear Views of a Drive Enclosure (When Only One I/O Module is Installed) I/O module (IOM#0) Cover Drive interface (IN) port Drive interface (OUT) port Power supply unit (PSU#0) Power supply unit (PSU#1) FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 23: Figure 1.9 Rear Views Of A Drive Enclosure (When Two I/O Modules Are Installed)

    Drive interface (IN) port Drive interface (OUT) port Power supply unit (PSU#0) Power supply unit (PSU#1) Power supply unit (PSU#2) Power supply unit (PSU#3) FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 24: Power Distribution Units (For Regions Other Than Emea&I)

    Power distribution unit for DX100 S3/DX200 S3 (AC200-240V, 2U, 12Outlets) There are 12 outlets. Figure 1.12 Power distribution unit for DX100 S3/DX200 S3 (AC200-240V, 2U, 12Outlets) Main line switch Outlet (OUTPUT) FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 25: Figure 1.13 Power Distribution Unit For Dx100 S3/Dx200 S3 (Ac200-240V, 2U, 16Outlets)

    Power distribution unit for DX100 S3/DX200 S3 (AC200-240V, 2U, 16Outlets) There are 16 outlets. Figure 1.13 Power distribution unit for DX100 S3/DX200 S3 (AC200-240V, 2U, 16Outlets) Main line switch Outlet (OUTPUT) FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 26: Chapter 2 Rack Installation

    Contact your sales representative or maintenance engineer if drives that are instal- led by default need to be uninstalled or moved to another slot. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...

  • Page 27: Installing Power Distribution Unit (For Regions Other Than Emea&I)

    This section describes how to install the power distribution unit in a rack. Do Not • Do not connect any devices other than the ETERNUS DX Disk storage system to the power distribution unit. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 28: Installing Power Distribution Unit (1U)

    3rd hole (M6 screw) (M6 screw) Power distribution unit 1st hole 1st hole (M6 screw) (M6 screw) Power distribution unit base line Bracket FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 29 The blank panel should be attached at the same height as the power distribution unit. Blank panel (Rack pillar: front) Power distribution unit (Rack pillar: rear) FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 30: Installing Power Distribution Unit (2U)

    Attachment procedure Clip the M5 cage nut tabs into the desired hole from the inside. Side view M5 cage nut Rack pillar (square hole) FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 31 The blank panel should be attached at the same height as the power distribution unit. Blank panel Power distribution unit (Rack pillar: front) (Rack pillar: rear) FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 32: Controller Enclosure Installation (For Regions Other Than Emea&I)

    Use the two plates to fasten the rack rails to the front rack pillars. Use the four washers to fasten the rack rails to the rear rack pillars. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
  • Page 33 (M5 screw) (M5 screw) Controller enclosure base line Rack rail Tighten the M4 screws of the rack rails that were slightly unscrewed in Step FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 34 Fasten the controller enclosure in the rack. Use three M5 screws to fasten it in the rack pillar. M5 screw M5 screws Attach the flange cover. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 35: 3.5" Type Drive Enclosure Installation (For Regions Other Than Emea&I)

    An "L" mark is on the inner side. [Left] (Rack pillar: front) Rack rail (right) An "R" mark is on the inner side. [Right] FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 36 (M5 screw) Bottom position of drive enclosure Rack rail Tighten the M4 screws of the rack rails that were slightly unscrewed in Step FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 37 Fasten the drive enclosure in the rack. Use four M5 screws to fasten it in the rack. M5 screws M5 screws Attach the flange cover. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 38: High-Density Drive Enclosure Installation (For Regions Other Than Emea&I)

    Rack rail (left) "Left" is on the exterior [Right] Rack rail (right) "Right" is on the exterior (Rack pillar: front) (Rack pillar: rear) FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 39 M4 screw (right) (Rack pillar: front) The M4 screw positions for the rack rails are determined by the high-density drive enclosure base line. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 40 Insert the M5 screws in the seventh holes above the base line to fasten the stopper brackets. High-density drive enclosure Front [Left] [Right] 7th hole 7th hole (M5 screw) (M5 screw) High-density drive enclosure base line Rack rail FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 41 Install the high-density drive enclosure in the rack. To keep it safe and stable, use a lifter to install or remove high-density drive • enclosures in racks. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 42 To attach the cable management arm, place the arm in the bracket on the rear of the high-density drive enclosure. After placing the arm in the bracket, firmly attach the arm with the pin. Cable management arm FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 43 Chapter 2 Rack Installation High-density Drive Enclosure Installation (for Regions Other than EMEA&I) Attach the front cover. Front cover FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 44: Chapter 3 Checking The Configuration Environment

    Multipath iSCSI SAN Remote support center LAN for Operation Management SNMP manager PC for Operation Management/ PC for setup Mail server Syslog server FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 45: Server Connection Preparation

    ETERNUS DX Disk storage system. If the server is connected, shut down the server, remove the cable, and then restart the server. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...

  • Page 46: Driver Installation

    To change the installation directory, click the [Browse] button and select the directory to install. To leave the settings unchanged, click the [Next] button. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...

  • Page 47: Iscsi Initiator Parameter Settings

    For the first startup, the dialog box that are shown below appears. If there is no problem with service startup settings, click the [Yes] button. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
  • Page 48 Chapter 3 Checking the Configuration Environment Server Connection Preparation On the [iSCSI Initiator Properties] screen, click the [Configuration] tab. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 49 To use the default initiator name, also click the [Change] button. This allows you to continue to use this initiator name even after changing the "server name". FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...

  • Page 50: Preparing The Pc Terminal For Setup

    IP address: 192.168.1.2 Subnet mask: 255.255.255.0 Check the settings of the Web browser. For details on the required settings, refer to "Configuration Guide (Web GUI)". FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 51: Lan Connection Preparation For Operation Management

    Enter the IP address for the RMT port of the ETERNUS DX Disk storage system. The RMT port is a LAN port that is used during initial setup and to connect to the remote support center. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...

  • Page 52: Lan Related Specifications

    — ´ ´ KMIP (key manage- 5696 ¡ (*2) ¡ (*2) — ment ) (*3) ¡: Possible △: Partially possible ´: Not possible FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 53 The default LAN operation mode is "Auto Negotiation" which allows the ETERNUS DX Disk storage system to automatically recognize 1000Base-T/100Base-TX/10Base-T and Full/Half-Duplex connections. However, some devices may require that a fixed communication mode be set. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 54: Chapter 4 Connecting Cables

    This section uses a controller enclosure with two controllers as an example to explain the connection pro- cedure. When one controller is installed, only Controller 0 (CM#0) has to be installed. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...

  • Page 55: Drive Enclosure Connection

    The last ports nearest to the edge are the DI (OUT) port of I/O module 0 in the drive enclosure of the largest DE-ID and the DI (OUT) port of I/O module 1 in the drive enclosure of the smallest DE-ID. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...

  • Page 56: Figure 4.1 Connecting Cables Between Enclosures (When Only One Controller Is Installed)

    Connection configuration between Connection configuration between Controller 0 and the I/O module line 0 Controller 1 and the I/O module line 1 FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 57 Clamp belts Flap bracket Clamp belts Cable management arm FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 58 1 and connecting drive enclosure 1 to drive enclosure 2. • When only one controller is installed Drive enclosure 2 Drive enclosure 1 Controller enclosure FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 59 Carefully check the connection origin and connection destination, and then attach the destination labels. Drive enclosure number IOM (I/O module) number DE01 0 CM (controller) number C M 0 0 FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 60 Connect the DI (OUT) port of I/O module 0 (IOM#0) in drive enclosure 1 to the DI (IN) port of I/O module 0 (IOM#0) in drive enclosure 2 with the cable between enclosures. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
  • Page 61 Connect the DI (OUT) port of I/O module 1 (IOM#1) in drive enclosure 2 to the DI (IN) port of I/O module 1 (IOM#1) in drive enclosure 1 with the cable between enclosures. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...

  • Page 62: Power Synchronized Unit Connection

    The high-density drive enclosure has four power supply units (PSU#0, PSU#1, PSU#2, and PSU#3). Make sure that power cords are connected to all power supply units. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...

  • Page 63: When No Power Distribution Units Are Installed

    Connect the power cord to the ETERNUS DX Disk storage system. Connect the power cord plugs to the power inlets of the power supply units. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...

  • Page 64: When 1U Power Distribution Unit Is Installed (For Regions Other Than Emea&I)

    To help with power cord management and prevent incorrect connections, attach labels to the power cords and make a note of connection origins and destinations. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
  • Page 65 Power distribution unit Use the power cord clamps to prevent the power plugs from coming unplugged. Attach the power cord clamps removed in Step FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 66: When 2U Power Distribution Unit Is Installed (For Regions Other Than Emea&I)

    The procedures to connect the power supply unit is same as Step 1 "4.4.1 When No Power Distribu- tion Units are Installed" (page 63). FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 67 : Connect OUTPUT#0-n of the power distribution unit to the PSU#0 inlet of the ETERNUS DX Disk storage system. : Connect OUTPUT#1-n of the Power distribution unit to the PSU#1 inlet of the ETERNUS DX Disk storage system. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
  • Page 68 : Connect OUTPUT#1-n of the Power distribution unit to the PSU#1 inlet of the ETERNUS DX Disk storage system. Use the power cord clamps to prevent the power plugs from coming unplugged. Attach the power cord clamps removed in Step FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 69 #0 side and the power distribution unit #1 side to different power sources. AC input cables Power distribution unit#1 Power distribution unit#0 Connect to power outlets. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 70: Chapter 5 General Settings

    Perform the basic settings to use the Advanced Copy function. For details on these settings and performing SnapOPC+, refer to "Chapter 9 Advanced Copy Settings" (page 157). FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 71: Figure 5.1 Example Of Differential Backup Settings With Snapopc

    Sunday data ETERNUS DX Disk storage system SnapOPC+ By mounting the copy destination volumes, the past data is recognized as drives by the server FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 72: Pc Terminal Connection

    LAN cable (for operation management). For the setup information of the PC terminal, refer to "3.3 Preparing the PC Terminal for Setup" (page 50). FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 73: Powering On

    ● For 1U Figure 5.4 ON Position (Marked "|") of the Main Line Switches on a 1U Power Distribution Unit Main line switch FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 74: Switching On And Off The Psu Switch On The Power Supply Unit

    Power supply unit (PSU#1) AC power is supplied to an enclosure. For the controller enclosure, the POWER LED on the power supply unit blinks green. • FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 75: Powering On

    Controller enclosure The POWER LED ( ) of the controller enclosure and the POWER LEDs ( ) of the drive enclosures are turned on. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 76: Eternus Web Gui Startup

    To change the language, click the [Option] button and select [English] or [Japanese] in [Language]. Enter the User ID and Password. User ID: root FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 77: Storage Management (Initial Setup 1)

    • Change User Password • Set Thin Provisioning • Register Advanced Copy License • Register SED Authentication Key • Set Network Environment • FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 78 The information that is set here is used for network management by SNMP. The name of the ETER- NUS DX Disk storage system is displayed in the login and operation screens of ETERNUS Web GUI. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
  • Page 79 The [Change User Password] screen appears. Change the user password. Change the user password. Set the required items and click the [Next >>] button. A confirmation screen appears. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 80 Click the [OK] button. The Thin Provisioning is set and the change completion screen appears. Click the [Done] button. The [Register Advanced Copy License] screen appears. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 81 Register the SED authentication key. When Self Encrypting Drives (SEDs) are installed in the ETERNUS DX Disk storage system, register the SED authentication key. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 82 Reboot the ETERNUS DX Disk storage system according to the dis- played message. Set the network environment. Set the ETERNUS DX Disk storage system environment for network communication. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 83 Click the [OK] button. The network environment setting is applied and the setting completion screen appears. Click the [Done] button. The [Logout] screen appears. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 84: Lan Cable Connection (For Operation Management)

    Disable the STP function of the LAN switch port only for the ETERNUS DX Disk storage system connection or perform the Port-Fast setting. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 85 Connect the LAN cables of the MNT port to the network of the customer. If the RMT port is used for remote support, connect the LAN cable of the RMT port to the network for remote support. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...

  • Page 86: Firewall Settings

    Click the [System] tab on the navigation of the ETERNUS Web GUI screen. In [Category], click [Network]. The [Network] screen appears. Select the port to be set. In [Action], click [Firewall Setting]. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 87 ETERNUS DX Discovery Change the setting to "Disable". Click the [Set] button. In the confirmation screen, click the [OK] button. The firewall settings are applied. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 88: Raid Configuration Settings

    600GB SAS disk ´ 5 Operation RAID Manual RAID5 group (copy source) Backup RAID group Manual RAID5 2TB Nearline SAS disk ´ 3 (copy destination) FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 89 The [Create RAID Group] screen appears. Enter the name of the RAID group that is to be registered. Select "Manual" for "Create Mode". FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 90 The RAID group is registered and the registration completion screen appears. Click the [Done] button. The screen display returns to the [RAID Group] screen. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 91: Figure 5.8 Raid Group Information After Creation

    The following screen shows the RAID group information that is displayed after the RAID group is created. Figure 5.8 RAID Group Information After Creation FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...

  • Page 92: Operation Volume Creation

    Click the [Volume] tab on the navigation of the ETERNUS Web GUI screen. The [Volumes] screen appears. In [Action], click [Create]. The [Create Volume] screen appears. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 93 Then, create SDV and SDPV in the backup RAID group (RG1). For the creation procedure, refer to "5.7.3 Generation Management Volume (SDV) Creation" (page 94) "5.7.4 Temporary Work Volume (SDPV) Creation" (page 95). FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 94: Generation Management Volume (Sdv) Creation

    RAID Group / TPP Selection: Manual Manual Setting: RG1 Number of Volumes: 7 (*2) *1: Enter the capacity of the copy source volume during creation of SDV. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 95: Temporary Work Volume (Sdpv) Creation

    88). Figure 5.11 Temporary Work Volume (SDPV) Creation Backup RAID group (RG1) Temporary work volume 500GB sdpv (Snap Data Pool Volume) RAID5 (2+1) FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 96 Click the [OK] button. The volume is created and the registration completion screen appears. Click the [Done] button. The screen display returns to the [Volumes] screen. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 97: Hot Spare Registration

    This is only available to a specified RAID group. For a RAID group that contains important data, assign "Dedicated Hot Spare" in order to preferentially use the hot spare. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 98 Select the drive that is to be registered as the Global Hot Spare and click [Assign Global HS] in [Action]. A confirmation screen appears. Click the [OK] button. The Global Hot Spare is registered and the registration completion screen appears. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 99 Select the drive that is to be registered as the Dedicated Hot Spare and click [Assign Dedicated HS] in [Action]. The [Assign Dedicated Hot Spare] screen appears. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 100 The Dedicated Hot Spare is registered and the registration completion screen appears. Click the [Done] button. The screen display returns to the [Drives] screen. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 101: Chapter 6 Monitoring Settings

    In the [Setting based on Severity] tab screen, select the required items. On the screens that are displayed by clicking each level tab, select the required items. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...

  • Page 102: Various Notification Settings

    Gateway IP address and the Allowable IP address (IP address of the monitoring server or the network address to which the monitoring server belongs) on the [Setup Network Environment] screen of ETERNUS Web GUI. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 103 Select [Enable] for [SNMP Function], set the required items, and click the [Set] button. Select the LAN port that was set up in Step 1 for "LAN Port used for SNMP". A confirmation screen appears. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 104 The SNMP Manager settings are applied. Check the setting completion message and click the [Done] button. The screen display returns to the [Network] screen. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 105 The screen display returns to the [Network] screen. User setup In [Action], click [Setup SNMP User]. The [Setup SNMP Agent User] screen appears. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 106 In [Action], click [Setup SNMP Trap]. The [Setup SNMP Agent Trap] screen appears. In the trap list of the [Setup SNMP Agent Trap] screen, click the [Add] button. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 107 Download the MIB file that is registered in the ETERNUS DX Disk storage system. In [Action], click [Download MIB File]. The [Download MIB File] screen appears. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 108 The MIB file is saved. Check the setting completion message and click the [Done] button. The screen display returns to the [Network] screen. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 109: E-Mail Setup

    In the [Notification E-Mail] tab screen, set the required items. • Select "Yes" for "Notification E-Mail". • Enter the destination e-mail address or addresses for the Destination E-Mail Address fields. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 110 This item does not need to be changed from the default value for normal operation. Click the [Set] button to apply the specified settings. A confirmation screen appears. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 111: Syslog Setup

    To send messages in RFC5424 format to a target syslog server that supports RFC5424, select "on (RFC5424)". If this is not the case, select "on (RFC3164)". FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...

  • Page 112: Remote Support Setup

    REMCS is not specified or is stopped. When REMCS is used, suspend the REMCS function, and then ena- ble the AIS Connect function. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 113: Remote Support (By Ais Connect) Setup

    (Country Code : Country Name)". Perform the other additional settings that are required. Click the [Set] button. A confirmation screen appears. Click the [OK] button. The AIS Connect settings are applied. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 114: Remote Support (By Remcs) Setup

    On the navigation of the ETERNUS Web GUI screen, click [System]. The [System] screen appears. In [Category], click [REMCS] in [Remote Support]. The [Support Information] tab screen of the [Remote Support] screen appears. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 115 Disk storage system and the remote support center is checked. The connection check result is sent to the e-mail address that is set in "Result notification information". FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...

  • Page 116: Audit Log Setup

    To send messages in RFC5424 format to a target syslog server that supports RFC5424, select "on (RFC5424)". If this is not the case, select "on (RFC3164)". FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...

  • Page 117: Monitoring Server (Snmp Manager) Settings

    Register the file that was downloaded in "Download the MIB file" (Step 6) in "6.2.1 SNMP Trap Setup" (page 102) as the MIB definition file for the monitoring software. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 118: Transmission Test Execution

    In the [Send SNMP Trap Test] screen, click the [Send] button. A confirmation screen appears. Click the [OK] button. The test transmission of the SNMP Trap is performed. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 119: Send Test Mail

    The [System] screen appears. In [Category], click [Network]. The [Network] screen appears. In [Action], click [Setup E-Mail Notification]. The [Setup E-Mail Notification] screen appears. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 120 Check that the test mail is sent to the e-mail addresses that are set. For details on the event code and message of the test mail, refer to "Message List". FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...

  • Page 121: Chapter 7 Power Control Setup

    Power Resume function is enabled The ETERNUS DX Disk storage system is automatically turned on when power is restored after a power failure. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 122 The Auto Power function and/or the Power Resume function setting is applied. Check the setting completion message and click the [Done] button. The screen display returns to the [System Settings] screen. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 123: Connection Setup For Power Synchronized Unit

    To control power supply with servers in a network to which the ETERNUS DX Disk storage system does • not belong, set "Gateway" and specify the server IP address or the network address in "Allowable IP Address". FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 124 The network environment settings are applied. Check the setting completion message and click the [Done] button. The screen display returns to the [System Settings] screen. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 125: Chapter 8 San Connection Settings

    Click the [Connectivity] tab on the navigation of the ETERNUS Web GUI screen. On the [Connectivity] screen, click [Host Response] in [Category]. In [Action], click [Add Host Response]. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 126: Host Affinity Settings

    For the settings for connection using other interfaces, refer to "Configuration Guide (Web GUI)". Also refer to "Configuration Guide -Server Connection-" as required. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 127 The iSCSI host group is added and the registration completion screen appears. Click the [Done] button. The screen display returns to the [Host Group] screen. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 128 • Specify [ON] to use unidirectional CHAP authentication or bidirectional CHAP authentication for the target port and [OFF] to use neither of them. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 129 The port parameter is set and the setting completion screen appears. Click the [Done] button. The screen display returns to the [iSCSI Port Group] screen. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 130 The CA port group is created and the setting completion screen appears. Click the [Done] button. The screen display returns to the [CA Port Group] screen. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 131 Enter the number for the first LUN and number of LUNs to allocate to the LUN group in [LUN Setting], select the number for the first volume to be allocated, and click the [OK] button. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
  • Page 132 Select the "Host Group", the "CA Port Group", and the "LUN Group" that are to be associated. Click the [Browse] button in [Host Group]. A screen to select the host group appears. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 133 [Host — CA Port Connection], and click the [Create] button. A confirmation screen appears. Click the [OK] button. The host affinity is created and the registration completion screen appears. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 134: Ca Reset Group Settings

    Set the CA reset group member ports and click the [Set] button. In the confirmation screen, click the [OK] button. Click the [Done] button to return to the [CA Reset Group] screen. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 135: Server Connection Setup

    After confirming that the ETERNUS DX Disk storage sys- tem is in READY status, turn on the server. On the [iSCSI Initiator Properties] screen, click the [Discovery] tab. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 136 When setting access restrictions, the settings related to CHAP authentication is required. For details on CHAP authentication, refer to "Configuration Guide -Server Connection-". FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 137 To enable mutual authentication, select [Perform mutual authentication]. Click the [OK] button. The screen display returns to the [Discover Target Portal] screen. Click the [OK] button. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 138 On the [iSCSI Initiator Properties] screen, click the [Targets] tab. Confirm that the specified settings are correctly reflected to [The system will look for Targets on follow- ing portals]. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 139 On the [iSCSI Initiator Properties] screen, click the [Targets] tab. Confirm whether the specified contents in [The system will look for Targets on following portals] have been applied correctly before checking connection. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 140 On the [Advanced Settings] screen, specify the following items under [Connect using] and click the [OK] button. Local adapter: Microsoft iSCSI Initiator Initiator IP: IP address of the server (A in Figure 8.1) FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 141 Target portal IP: IP address of the ETERNUS DX Disk storage system (C in Figure 8.1) Confirm that the [Add this connection to the list of Favorite Targets.] checkbox is selected and click the [OK] button. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 142 Initiator IP: IP address of the server (B in Figure 8.1) Target portal IP: IP address of the ETERNUS DX Disk storage system (D in Figure 8.1) FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 143 Chapter 8 SAN Connection Settings Server Connection Setup Confirm that [Status] of the two targets has changed to [Connected] and click the [OK] button. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 144: Lun Recognition Check

    The following procedure explains how to check LUN using the Windows Device Manager. Open [Device Manager] and expand [Disk drives]. Confirm that the same number of "FUJITSU..." items are displayed as the number of LUNs that are set. If the example is used, eight "FUJITSU..." items are displayed.
  • Page 145 CM#0 CA#1 Port#0 g CAID = 20 CM#1 CA#1 Port#0 g CAID = 22 CM#0 CA#1 Port#1 g CAID = 21 CM#1 CA#1 Port#1 g CAID = 23 FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 146: Disk Partition Settings

    If the [Initialize Disk] screen appears, confirm that all the disks are selected and click the [OK] button. Then proceed to Step Select the checkbox for eight disks in this example. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 147 The LUNs that are set with the ETERNUS DX Disk storage system are recognized as [Offline]. Right-click all the disks displayed as offline, and select [Online]. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
  • Page 148 SAN Connection Settings Server Connection Setup [Offline] changes to [Not initialized]. Right-click all the disks to be changed to online, and select [Initialize Disk]. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 149 When the [Initialize Disk] screen appears, confirm that all the disks are selected and click the [OK] but- ton. Confirm that the initialized disks are displayed as [Online]. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 150: Disk Settings

    The following procedure explains how to set up the operation disk. Select [Disk Management] from [Computer Management]. On the [New Simple Volume Wizard] screen, click the [Next] button. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 151 Perform the settings as shown below. File system Volume Drive that is to be Volume No. Type Capacity name created NTFS main Standard FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 152 [Format Partition] appears. Click the [Next] button. [Completing the New Simple Volume Wizard] appears. Click the [Finish] button. Check that the specified settings are displayed correctly. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 153 Set up the disk created in [Snap Data Volume]. During volume creation, right-click the disk created in [Snap Data Volume] and select [New Simple Vol- ume]. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 154 Without changing the default settings of [Specify Volume Size], click the [Next] button. Assign a drive letter in [Assign Drive Letter or Path] and click the [Next] button. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
  • Page 155 *1: The capacity that is displayed in "( )" is the copy source capacity. Select [Do not format this volume], and click the [Next] button. [Completing the New Simple Volume Wizard] appears. Click the [Finish] button. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 156 Step 7 for all the disks created in [Snap Data Volume]. In this case, seven disks are created as [Drive Letter: Assigned, RAW]. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 157: Chapter 9 Advanced Copy Settings

    Low Priority mode. • Low Priority This mode reduces the effect on host access. Select this mode when using EC and/or OPC during operation. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 158 EC/OPC priority setting starts. In the setting completion screen, click the [Done] button. The screen display returns to the [Setting (Advanced Copy)] screen. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 159: Copy Table Size Settings

    Specify the copy table size. Specify "512 (MB)" in this example. • Table Size Threshold Select the threshold for the table size usage rate. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 160 Copy table size setting starts. In the setting completion screen, click the [Done] button. The screen display returns to the [Setting (Advanced Copy)] screen. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 161: Copy Parameter Settings

    In [Action] on the [Setting] screen, click [Modify Copy Parameter]. Set the required items and click the [Set] button. In the confirmation screen, click the [OK] button. Copy table size setting starts. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 162: Performing A Copy (Snapopc+)

    On the navigation of the ETERNUS Web GUI screen, click the [Advanced Copy] tab. In [Action], click [Create SnapOPC+]. Click the [Browse] button of the copy source volume. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 163 Select the "No.: 0, Name: main" volume. In the same way as the copy source volume, click the [Browse] button of the copy destination volume. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
  • Page 164 In the confirmation screen, click the [OK] button. The SnapOPC+ session starts. Click the [Done] button to return to the [Advanced Copy] screen. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 165 In this case, the copy source volume number is "0" and the copy destination volume numbers are from "1" through to "7". Open [Disk Management] from [Computer Management]. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 166 Check if the file that was created in Step 8 "■ Operation Disk Settings" (page 150) "8.2.3.2 Disk Settings" (page 150) is displayed for the copy source drive. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 167 Old data can be restored by simply copying and pasting the data files that are to be restored from the server. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 168: Chapter 10 System Status Check

    ETERNUS DX Disk storage system. Check the status of each component on the [Storage] screen. If there is a component in Warning or Error status, contact your sales representative or maintenance engi- neer. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 169: Raid Group Check

    GUI screen. In the [RAID Group (Basic Information)] screen that appears, select which RAID group to check the information for and click the No. or name of this RAID group. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...

  • Page 170: Volume Check

    In the [Volume (Basic Information)] screen that appears, select which volume to check the informa- tion for and click the No. or name of this volume. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...

  • Page 171: Checking Copy Sessions

    Click the [Start] button for Windows, expand [ETERNUS Multipath Driver] from [All Programs], and open [ETERNUS Multipath Manager]. Check that the LUN status is normal (that the signal icon is blue). FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...

  • Page 172: Powering Off

    Press and hold the Power switch of the controller enclosure for four seconds or more. Power switch Controller enclosure The READY LED ( ) on the controller enclosure is turned off. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 173 When a Power Synchronized Unit is Used If the server is turned off, the ETERNUS DX Disk storage system is also turned off. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 174: Chapter 11 Solution Configuration

    (ACM Manager). REC related settings and connection path settings must be performed in the ETERNUS DX Disk storage sys- tem. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 175 Register the replication source volumes and the replication destination volumes. For more details on the settings for ETERNUS SF AdvancedCopy Manager, refer to "ETERNUS SF AdvancedCopy Manager Operation Guide". FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 176: Performance/Tuning

    Storage Cruiser responses for prioritized operations Volumes for Server A Volumes for Server C Volumes for Server B ETERNUS DX Disk storage system FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 177: Configuration Procedure

    Specify the target performance value for each volume. For more details on the settings for ETERNUS SF Storage Cruiser, refer to "ETERNUS SF Storage Cruiser Opera- tion Guide". FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 178: Green

    Business drives Backup drives ETERNUS DX Disk storage system Server Collects power consumption and temperature data for each storage system ETERNUS SF Storage Cruiser FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 179 (ETERNUS SF Storage Cruiser). For more details on the settings for ETERNUS SF Storage Cruiser, refer to "ETERNUS SF Storage Cruiser Opera- tion Guide". FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 180: Cloud Platform

    RAID group and Thin Provisioning Pool creation Settings of a LAN for operation management (such as the firewall settings and the SSH connection set- tings) FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 181: Vmware Linkage

    Install ETERNUS vCenter Plug-in in a Windows server where VMware Web Client Server is installed. Server-side settings • Install ETERNUS vCenter Plug-in and then register the ETERNUS DX Disk storage system as a management target device. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
  • Page 182 For more details on the settings for ETERNUS SF Storage Cruiser, refer to "ETERNUS SF Web Console Manual" and "ETERNUS SF Storage Cruiser Operation Guide". FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...

  • Page 183: Microsoft Linkage

    Create ODX volumes after enabling the ODX settings for the Advanced Copy function in the ETERNUS DX Disk storage system with ETERNUS Web GUI. For details on the SCVMM2012 settings, refer to the manual of the SCVMM2012. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...

  • Page 184: Security

    A Syslog sever is required for the destination for the transmission of the audit log that is collected. Note that ETERNUS SF KM is required when linking with the key management server. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
  • Page 185 Specify the group name that is registered in the ETERNUS DX Disk storage system and the name (ma- chine ID) of the ETERNUS DX Disk storage system that is set for key management. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
  • Page 186 ETERNUS DX Disk storage system. For details on the setting procedures and setting items, refer to "ETERNUS SF KM Installation Guide". FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
  • Page 187 However, Fujitsu shall assume no responsibility for any operational problems as the result of errors, omissions, or the use of information in this manual. Fujitsu assumes no liability for damages to third party copyrights or other rights arising from the use of any information •...

This manual is also suitable for:

Eternus dx100 s3

Table of Contents