REPLACING THE BATTERY
The LED will not flash during transmission if the battery is low. Replace
the battery as follows.
1. Remove the screw from the case back, then remove the case back.
2. Insert the blade of a small screwdriver under the battery as shown.
3. Twist the screwdriver to release the battery.
4. With the Positive (+) end of a new battery facing UP, insert the battery
as shown, sliding it under the gold tab, then pressing down to snap into
place.
IMPORTANT: Positive (+) end must face up.
Use Maxell CR2032 or Duracell DL2032 lithium battery only.
5. Replace the case back and replace the screw to secure the case.
• Improper installation will result in damage to the
battery.
• Do not remove the printed circuit board.
Failure of Replaceable Batteries
This wireless key has been designed to provide several years of battery
life under normal conditions. The expected battery life is a function of the
device environment, usage and type. Ambient conditions such as high
humidity, high or low temperatures, or large temperature fluctuations may
reduce the expected battery life.
If the batteries need to be replaced, this device reports a low battery
condition to the control panel as a trouble condition when a button is
pressed. In addition the LED will not flash when a button is pressed.
However, if the device is unused for a long period of time, it may fail to
operate as expected. Regular testing and maintenance will keep the
system in good operating condition for the lifetime of the product.
IMPORTANT! This wireless key is intended as a convenience to the
user and should not be considered as a life safety device. If life
safety is important, please select a supervised wireless key (e.g.
type 5802MN).
SPECIFICATIONS
Unit Dimensions:
2.25" x 1.25" x 0.5"
(57mm x 31.75mm x 12.7mm)
Battery: 3V, 210mAh, Maxell CR2032, Duracell DL2032
IC MODEL No. 5834
WARRANTY INFORMATION
For the latest warranty information, please go to:
http://www.security.honeywell.com/hsc/resources/wa/index.html
REFER TO THE INSTALLATION INSTRUCTIONS FOR THE
CONTROL WITH WHICH THIS DEVICE IS USED FOR
LIMITATIONS OF THE ENTIRE ALARM SYSTEM.
Ê800-05637V1ZŠ
800-05637V1 11/10 Rev. A
Removing the Battery
GOLD
TAB
REMOVE
SCREW
TO OPEN
CASE
BATTERY
TO REMOVE BATTERY,
GENTLY SLIDE SCREWDRIVER
BLADE UNDER BATTERY HERE
5834-004-V0
Installing the Battery
INSTALL WITH POSITIVE (+)
INSTALL UNDER
SIDE UP. SLIP BATTERY
GOLD TAB
UNDER GOLD TAB THEN
THEN PRESS
PRESS DOWN
DOWN
IMPORTANT
POSITIVE (+)
SIDE MUST
FACE UP
5834-005-V0
FEDERAL COMMUNICATIONS COMMISSION
STATEMENTS:
The user shall not make any changes or modifications to
the equipment unless authorized by the installation
Instructions or User's Manual. Unauthorized changes or
modifications could void the user's authority to operate the
equipment.
FCC NOTICE
This device complies with Part 15 of FCC Rules, and RSS
210 of IC. Operation is subject to the following two
conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any
interference received, including interference that may
cause undesired operation.
Cet appareil est conforme à la partie 15 des règles de la
FCC & de RSS 210 des industries Canada. Son
fonctionnement est soumis aux conditions suivantes: (1)
Cet appareil ne doit pas causer d'interferences nuisibles.
(2) Cet appareil doit accepter toute interference reçue y
compris les interferences causant une reception
indesirable.
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
Copyright © 2010 Honeywell International Inc.
www.honeywell.com/security
- Quick Links:
- Programming
- Specifications
- Replacing the Battery
Hide quick links:
